top of page

Gordon Elger

​

Technische Hochschule Ingolstadt

​

* All members of the platform can watch the entire presentation.

 

Please register to become a member.

Additive manufacturing of Circular Flexible Electronics: Cu Particle-free Inks on Recyclable Biopolymers

Sustainable Electronics RESHAPED 2026 Berlin

The Future of Electronics RESHAPED 2026 Berlin

21 October 2026

Berlin, Germany

Estrel Berlin Hotel & Convention Center:
Sonnenallee 225, 12057 Berlin

This work presents a process-integrated approach for circular flexible electronics based on biodegradable polymer substrates and low-temperature additive copper metallization. The study evaluates Polyhydroxybutyrate (PHB) and bio-synthesized Polyamide‑4 (PA‑4) as thin-film substrates compatible for printed conductive trace formation and solvent-based end-of-life recovery, targeting a reduction in fossil-derived materials and subtractive fabrication steps typical of FR‑4 PCB technology. PA 4 is synthesized via metabolically engineered E. coli producing γ aminobutyric acid (GABA), which is converted to the Poly(2 pyrrolidone) precursor and subsequently polymerized. PHB, representing the Polyhydroxyalkanoate (PHA) family, is synthesized using established microbial production routes and combine functional performance with intrinsic biodegradability. Substrates are fabricated using drop-casting and spray-coating to obtain flexible films with thickness in the range of 25-35 µm, as measured by optical profilometry. Surface roughness and film uniformity are optimized to ensure reproducible ink wetting and line edge definition. Thermogravimetric analysis (TGA) defines the upper thermal process limit below the onset of polymer degradation, establishing a constrained sintering window for Cu metallization. For conductor formation, a copper complex ink based on copper formate tetrahydrate–amine chemistry is developed. Additives are incorporated to tune viscosity and surface tension for both dispensing and inkjet printing. Patterning is fully additive, eliminating subtractive etching and associated copper waste. Printed features are thermally decomposed and sintered at 150 °C for 30 min under N2 atmosphere to suppress oxidation and remain within the polymer thermal limits. Cross-sectional SEM analysis shows continuous copper layers with an average thickness of ~3 µm and good interfacial conformity to the polymer surface. The resulting films exhibit a bulk resistivity of 78 µΩ·cm, corresponding to ~45× bulk copper, which is consistent with low-temperature processed metal-organic decomposition inks. No macroscopic delamination is observed after sintering, confirming compatibility between the Cu-complex decomposition chemistry and the biopolymer substrates. To address end-of-life processing, printed samples are subjected to a solvent-based recycling protocol. Following isopropanol cleaning, substrates are dissolved using a selective depolymerization-assisted solvent system enabling separation of copper residues from the polymer fraction. The recovered polymer is recast at 75 °C for 30 min under ambient conditions to form second-generation films with comparable thickness and surface topography. This demonstrates that additive copper metallization is compatible with closed-loop substrate recovery without energy-intensive thermal reprocessing. The integration of biologically derived PHB and PA 4 substrates, low-temperature Cu-complex ink metallization, and solvent-assisted material recovery establishes a fabrication-relevant pathway toward circular microelectronic systems. The presented process chain is compatible with thin, flexible form factors and defines a reduced thermal and material budget compared to conventional PCB manufacturing, while maintaining electrically functional copper interconnects.

Watch the 5-minute excerpt from the talk

Read the summary

How does copper formate ink formulation compare to traditional inks, and what are the thermal limits of PHB versus PA4 biopolymers?

05:34 - 07:03

Read the summary

What resistivity does copper ink reach on PHB after 140 °C sintering, and how is the polymer separated for recycling?

12:05 - 13:47

Read the summary

At what temperature does complexed copper formate decompose to copper without exceeding PHB's 170°C processing limit?

08:31 - 10:20

Video highlights and other talks by this speaker appear here.

More presentations from
Technische Hochschule Ingolstadt

The Future of Electronics RESHAPED 2024 Berlin

23 October 2024

Particle Free Copper Inks

Gordon Elger

Estrel

Berlin, Germany

The TechBlick Platform: Why Join?

Onsite Admission

With your Hybrid Individual or Group Pass, you can attend one or more of our world-class conferences and exhibitions around the world, including Electronics RESHAPED USA or Europe, MicroLED Connect, AR/VR Connect, Perovskite Connect, Sustainable Electronics RESHAPED, and more…

CONTACT US

KGH Concepts GmbH

Mergenthalerallee 73-75, 65760, Eschborn

+49 17661704139

admin@techblick.com

TechBlick is owned and operated by KGH Concepts GmbH

Registration number HRB 121362

VAT number: DE 337022439

  • LinkedIn
  • YouTube

Sign up for our newsletter to receive updates on our latest speakers and events AND to receive analyst-written summaries of the key talks and happenings in our events.

Thanks for submitting!

© 2026 by KGH Concepts GmbH

bottom of page