Alexander Görk | Hamamatsu: What reliability evidence exists for laser soldering on low-temperature substrates?
19:53 - 21:09
Other snippets from this talk
Summary of the clip:
What reliability evidence exists for laser soldering on low-temperature substrates?
Asked directly how solder-free assembly proves reliable, the answer is collaboration: end users and material suppliers working closely together. There has to be a certain project and industry partner to do all the things. Reliability evidence is therefore built inside partnered projects rather than from a standalone qualification campaign.
Their experience with low-temperature substrates is the core argument: soldering time is very long, and sometimes too long for ramping up. Oven speeds are too long, so lines cannot ramp up. That is why the need is seen to change to laser soldering or other technologies, and why this is the big argument.
The reliability answer is incremental: these are feasibility studies where each project teaches something. With end users and material suppliers tied closely together and an industry partner in place, the evidence grows project by project on low-temperature substrates, where long soldering times and slow oven speeds cannot support ramp-up.
In this short video, you can learn:
* Reliability work on solder-free assembly runs through joint projects with end users, material suppliers and an industry partner.
* On low-temperature substrates, soldering time is very long and sometimes too long for ramping up.
* Slow oven speeds are the stated reason to change to laser soldering or other technologies.
📋 **Clip Abstract** The clip addresses how solder-free interconnection reliability is demonstrated: through close collaboration with end users and material suppliers inside partnered projects, each one a feasibility study. The technical driver is that low-temperature substrates need very long soldering times, sometimes too long for ramping up, which is the stated argument for laser soldering or other technologies.
About the speaker:
* Speaker: Alexander Görk
* Company: Hamamatsu
* Event: Electronics RESHAPED 2026 | Berlin
* Location: Estrel, Berlin
USA: The Future of Electronics RESHAPED | USA
📅 Save the date: 9 and 10 June 2027
📍 Mountain View, California (Silicon Valley)
📋 Info: https://www.techblick.com/electronicsreshapedusa
Europe
The Future of Electronics RESHAPED | Berlin
📅 Save the date: 20 and 21 October 2027
📍 Berlin, Germany
📋 Info: https://www.techblick.com/electronicsreshaped
#LaserSoldering, #LowTemperatureSubstrates, #SolderReflow, #FeasibilityStudies, #PrintedElectronics, #AdditiveElectronics
This is a highlight of the presentation:
Laser Soldering in Printed Electronics
More Highlights from the same talk.
04:52 - 06:39
How can a laser measure solder-joint temperature without an external pyrometer?
How can a laser measure solder-joint temperature without an external pyrometer?
The lasers carry a special feature inside: they measure the temperature generated directly by the laser process on the sample. That heat is very informative, because it is a direct feedback signal for process quality. Conventionally an external pyrometer is mounted on the laser head itself or used as a separate device at a certain angle, which introduces a problem when the system is not 100% coaxial and misalignment appears.
The alternative is a fiber feedback loop that collects the thermal information, specifically the near-infrared light coming from the heat generated by the laser process, and feeds it back into the system for direct measurement. That signal is a direct indicator of process quality, and it matters especially in laser soldering, where temperature profiles decide whether you reach the required temperature or exceed it.
In soldering it is critical to know whether the target temperature is achieved, because difficult changes in the material, such as shifts in absorption or unforeseen conditions, are not visible at the beginning. That is why measuring matters, and it is possible with the laser alone, with no external device. Selling the laser is not enough, though; the process behind it has to be understood.
In this short video, you can learn:
* The laser collects near-infrared light from process-generated heat through a fiber feedback loop and measures it internally, without an external pyrometer.
* External pyrometers mounted on the head or at an angle suffer misalignment when the system is not 100% coaxial.
* In laser soldering the thermal signal shows whether the required temperature is reached or exceeded, catching absorption changes and unforeseen conditions early.
📋 **Clip Abstract** An internal fiber feedback loop captures near-infrared light from the heat generated by the laser process and returns it to the system as a direct measure of process quality, removing the misalignment risk of an external pyrometer. In laser soldering this thermal signal verifies whether the target temperature profile is reached or exceeded, including when absorption changes or unforeseen conditions are invisible at the start.
About the speaker:
* Speaker: Alexander Görk
* Company: Hamamatsu
* Event: Electronics RESHAPED 2026 | Berlin
* Location: Estrel, Berlin
USA: The Future of Electronics RESHAPED | USA
📅 Save the date: 9 and 10 June 2027
📍 Mountain View, California (Silicon Valley)
📋 Info: https://www.techblick.com/electronicsreshapedusa
Europe
The Future of Electronics RESHAPED | Berlin
📅 Save the date: 20 and 21 October 2027
📍 Berlin, Germany
📋 Info: https://www.techblick.com/electronicsreshaped
#LaserSoldering, #FiberFeedbackLoop, #NearInfraredThermometry, #TemperatureProfileControl, #PrintedElectronics, #RollToRollProcessing
13:23 - 14:53
How fast is single-spot SMD soldering, and how does galvo scanning use temperature feedback?
How fast is single-spot SMD soldering, and how does galvo scanning use temperature feedback?
For single-spot SMD soldering, the demonstrated processing time is 0.4 seconds — 400 milliseconds — for one spot. That shot is not the limit: the approach can be scaled up. The machine concept always uses dispensed solder paste, in parallel with other laser soldering machine builders.
With a galvo scanner there is more freedom. In the collaboration with Rayles, the temperature signal is routed through the scanner into the laser. Rayles contributes software features, camera alignment and well-designed scanning parameters; the laser side contributes its temperature feedback loop. Galvo scanning is shown slowed down step by step, but it can be much faster — instantaneously and simultaneously.
The galvo demonstration uses the same laser parameters, though the spot size differs slightly for the galvo scanner system. Even with that difference, the process window is quite large. The comparison contrasts one-spot SMD soldering at 400 milliseconds with a scanner path that can be scaled to faster, simultaneous processing.
In this short video, you can learn:
* Single-spot SMD soldering achieved 0.4 seconds, or 400 milliseconds, processing time for one spot and can be scaled up.
* The galvo scanner approach passes the temperature signal through the scanner into the laser, enabling use of the temperature feedback loop.
* Rayles adds software features, camera alignment and well-designed scanning parameters, while the galvo process window remains quite large despite a slightly different spot size.
📋 **Clip Abstract** Single-spot SMD soldering is demonstrated at 0.4 seconds, or 400 milliseconds, per spot and can be scaled up, using dispensed solder paste. A galvo scanner collaboration with Rayles routes the temperature signal through the scanner into the laser, combining camera alignment and scanning software with a temperature feedback loop; the process window is quite large, and scanning can be much faster, even instantaneous and simultaneous.
About the speaker:
* Speaker: Alexander Görk
* Company: Hamamatsu
* Event: Electronics RESHAPED 2026 | Berlin
* Location: Estrel, Berlin
USA: The Future of Electronics RESHAPED | USA
📅 Save the date: 9 and 10 June 2027
📍 Mountain View, California (Silicon Valley)
📋 Info: https://www.techblick.com/electronicsreshapedusa
Europe
The Future of Electronics RESHAPED | Berlin
📅 Save the date: 20 and 21 October 2027
📍 Berlin, Germany
📋 Info: https://www.techblick.com/electronicsreshaped
#LaserSoldering, #GalvoScanner, #SMDSoldering, #TemperatureFeedbackLoop, #PrintedElectronics, #AdditiveElectronics
10:43 - 12:46
Why use low-temperature solder paste and non-absorbing substrates for laser soldering?
Why use low-temperature solder paste and non-absorbing substrates for laser soldering?
Standard solder paste generates a heat effect that is dramatically high for sensitive substrates, which is why low-temperature pastes are preferred — Eversolt from Ishikawa was designed for laser soldering and worked well in many applications. SAC305 remains widely used in SMD and hybrid electronics; it can be soldered, but the heat effect is higher and more laser input is needed.
The limit is not laser power but what comes next: whether the substrate is strong enough to resist the heat generated by the solder paste itself. Rigid PCBs are no problem. For flexible circuits, substrates that do not absorb the laser power are preferred — PET, PN, PC or Kapton — giving more freedom in designing the process.
Process design offers different approaches. On one hand, irradiation with a single spot; 3D printing is one of them. On the other, a galvo scanner with the laser is widely used. With both — single spot and galvo scan — thermal information measured in the laser can be used, which is very important for laser soldering.
In this short video, you can learn:
* Low-temperature solder paste is selected because the heat effect of standard paste is dramatically high on sensitive substrates, not because the joint cannot be heated at all.
* SAC305 can be laser soldered in SMD and hybrid electronics, but it demands more laser input and shifts the question to the substrate's heat resistance.
* PET, PN, PC and Kapton substrates that do not absorb the laser power allow more freedom in designing the soldering process.
📋 **Clip Abstract** Laser soldering on flexible substrates depends less on laser power than on the heat the solder paste injects into the substrate, which is why low-temperature pastes designed for laser soldering are preferred over SAC305. Non-absorbing PET, PN, PC and Kapton substrates, combined with single-spot or galvo-scan irradiation and in-laser thermal measurement, widen the process window.
About the speaker:
* Speaker: Alexander Görk
* Company: Hamamatsu
* Event: Electronics RESHAPED 2026 | Berlin
* Location: Estrel, Berlin
USA: The Future of Electronics RESHAPED | USA
📅 Save the date: 9 and 10 June 2027
📍 Mountain View, California (Silicon Valley)
📋 Info: https://www.techblick.com/electronicsreshapedusa
Europe
The Future of Electronics RESHAPED | Berlin
📅 Save the date: 20 and 21 October 2027
📍 Berlin, Germany
📋 Info: https://www.techblick.com/electronicsreshaped
#LowTemperatureSolderPaste, #LaserSoldering, #GalvoScanner, #KaptonSubstrate, #PrintedElectronics, #FlexibleHybridElectronics
About this talk
→ Laser Soldering in Printed Electronics · Alexander Görk · The Future of Electronics RESHAPED 2026 Berlin
Other talks by Alexander Görk
- Leveraging Laser Processing for Sustainable Printed Electronics – Laser Sintering, Encapsulation & Soldering · The Future of Electronics RESHAPED 2025


