top of page

Anaghim Nasri

BLACKLEAF

* All members of the platform can watch the entire presentation.

 

Please register to become a member.

Anaghim Nasri | BLACKLEAF: Why is printed film opacity a misleading indicator of electrothermal performance in graphene heating inks?

04:55 - 06:50

Other snippets from this talk

Summary of the clip:

Why is printed film opacity a misleading indicator of electrothermal performance in graphene heating inks?

A common challenge is that the ink has relatively low solid content and the printed film looks less opaque than a typical carbon film, raising the question of whether it really performs. For a heater, opacity is not the real indicator; percolation is, meaning a continuous conductive network from one electrode to another.

If particles form isolated clusters, current is forced through paths that overheat, creating cold zones and hot spotsβ€”even if the film looks dark and covered. The illustrated flakes are about six microns with one nanometer thickness, giving around 6,000 aspect ratio, a huge number compared with conventional carbon inks.

With such flakes, the network percolates at low loading and reaches heat resistance down to 24 ohm per square per mile, so current and heat spread evenly. The conclusion is that electrothermal response is set by ink microstructure, not empirical tuning: engineer for connectivity, not coverage.

In this short video, you can learn:
* Film opacity does not indicate heater performance; percolation and a continuous conductive network do.
* Isolated particle clusters force current through overheating paths, producing cold zones and hot spots.
* Six-micron, one-nanometer flakes provide around 6,000 aspect ratio and percolate at low loading, with heat resistance down to 24 ohm per square per mile.

πŸ“‹ **Clip Abstract** The clip explains why low solid content and less opaque printed films can still perform as heaters: opacity is not the indicator, percolation is. It contrasts isolated clusters that create hot spots with high-aspect-ratio flakes that percolate at low loading, spread current and heat evenly, and reach 24 ohm per square.

About the speaker:
* Speaker: Anaghim Nasri
* Company: BLACKLEAF
* Event: Electronics RESHAPED 2026 | Berlin
* Location: Estrel, Berlin

USA: The Future of Electronics RESHAPED | USA
πŸ“… Save the date: 9 and 10 June 2027
πŸ“ Mountain View, California (Silicon Valley)
πŸ“‹ Info: https://www.techblick.com/electronicsreshapedusa

Europe
The Future of Electronics RESHAPED | Berlin
πŸ“… Save the date: 20 and 21 October 2027
πŸ“ Berlin, Germany
πŸ“‹ Info: https://www.techblick.com/electronicsreshaped

#HighAspectRatioFlakes, #ConductivePercolation, #HotSpotFormation, #LowLoadingHeaterInk, #PrintedElectronics, #ElectrothermalInks

This is a highlight of the presentation:

Engineering Water-Based Graphene Inks for Scalable Printed Heating Systems

​

21 and 22 OCT 2026

Estrel, Berlin

Organised By:

TechBlick

​

More Highlights from the same talk.

02:53 - 05:00

How is water-based few-layer graphene ink engineered for reliable industrial printing and scalable printed heaters?

How is water-based few-layer graphene ink engineered for reliable industrial printing and scalable printed heaters?

The challenge is turning graphene into a printable, reliable ink. The NAI Black platform targets not maximum conductivity alone but a balance of dispersion stability, film formation, rheology and final device performance, so the ink prints reliably in industrial processes. That formulation work bridges advanced graphene material and graphene in a real product.

The approach starts from few-layer graphene produced from two up to five layers, with a lateral size of six microns, at industrial scale. It is incorporated into a water-based formulation with additives for stability and rheology. The inks are designed mainly for screen printing and can also work with spray or dip coating for high-volume production.

After printing and drying, conductive homogenous coatings are integrated directly into functional devices such as printed heaters. From mid-2027, production capacity will reach up to five tons per month, against estimated demand around 1,000 tons per year by 2030. The material is positioned as industrial supply, not lab material, ready for that demand.

In this short video, you can learn:
* NAI Black balances dispersion stability, film formation, rheology and device performance rather than only maximizing conductivity.
* The ink uses few-layer graphene of two to five layers and six-micron lateral size in a water-based formulation designed mainly for screen printing.
* Production capacity is planned to reach five tons per month from mid-2027 against around 1,000 tons per year demand by 2030.

πŸ“‹ **Clip Abstract** Water-based few-layer graphene inks are engineered by balancing dispersion stability, film formation, rheology and device performance for reliable industrial printing. The NAI Black platform uses two-to-five-layer, six-micron graphene in formulations mainly for screen printing, with capacity targeted at five tons per month from mid-2027 against estimated 1,000 tons per year demand by 2030.

About the speaker:
* Speaker: Anaghim Nasri
* Company: BLACKLEAF
* Event: Electronics RESHAPED 2026 | Berlin
* Location: Estrel, Berlin

USA: The Future of Electronics RESHAPED | USA
πŸ“… Save the date: 9 and 10 June 2027
πŸ“ Mountain View, California (Silicon Valley)
πŸ“‹ Info: https://www.techblick.com/electronicsreshapedusa

Europe
The Future of Electronics RESHAPED | Berlin
πŸ“… Save the date: 20 and 21 October 2027
πŸ“ Berlin, Germany
πŸ“‹ Info: https://www.techblick.com/electronicsreshaped

#GrapheneInk, #FewLayerGraphene, #ScreenPrinting, #PrintedHeaters, #PrintedElectronics, #ConductiveInks

14:18 - 16:13

Why does adding more printed layers of graphene ink eventually destroy electrical percolation instead of improving conductivity?

Why does adding more printed layers of graphene ink eventually destroy electrical percolation instead of improving conductivity?

A single graphene print step is described as enough to obtain uniform percolation, while a second print can be used to change sheet resistivity according to the final result. The comparison drawn is with carbon, which the questioner suggests may need two or three prints to reach even percolation.

There is a limit: the speaker warns that printing three graphene layers can create a paste-like texture and completely destroy percolation. Sheet resistivity then converts in the opposite way, so the intended final result is lost. Graphene is therefore described as not the easiest material to work with, although in their case it is the easiest.

The formulation uses a low solid content of graphene rather than approaching a high concentration or the percolation threshold. They report about 3% graphene inside the ink formulation. Compared with conventional carbon-based inks, this is described as really, really low, which is the opposite strategy to working at higher solid content.

In this short video, you can learn:
* One graphene print step was said to be sufficient for uniform percolation, with a second print available to adjust sheet resistivity.
* Printing three graphene layers can create a paste texture and completely destroy percolation, reversing the sheet-resistivity outcome.
* The ink formulation contains about 3% graphene solid content, described as very low versus conventional carbon-based inks.

πŸ“‹ **Clip Abstract** This clip examines how graphene ink layer count affects percolation and sheet resistivity in printed films. It contrasts a one-print uniform percolation with the failure mode at three layers and notes a low 3% graphene solid-content formulation.

About the speaker:
* Speaker: Anaghim Nasri
* Company: BLACKLEAF
* Event: Electronics RESHAPED 2026 | Berlin
* Location: Estrel, Berlin

USA: The Future of Electronics RESHAPED | USA
πŸ“… Save the date: 9 and 10 June 2027
πŸ“ Mountain View, California (Silicon Valley)
πŸ“‹ Info: https://www.techblick.com/electronicsreshapedusa

Europe
The Future of Electronics RESHAPED | Berlin
πŸ“… Save the date: 20 and 21 October 2027
πŸ“ Berlin, Germany
πŸ“‹ Info: https://www.techblick.com/electronicsreshaped

#GrapheneInk, #PercolationNetwork, #SheetResistivity, #PasteTexture, #PrintedElectronics, #ConductiveInks

07:04 - 09:08

What operating limits and manufacturing repeatability can flexible graphene printed heaters achieve across volume production?

What operating limits and manufacturing repeatability can flexible graphene printed heaters achieve across volume production?

The heater platform spans 3 to 480 volts, 0.01 to 6 watts per square centimetre and up to 200 degrees Celsius peak. Configuration happens at three levels: the ink, the printed pattern and the architecture. Substrates include PET, PU and polyamide textiles, with silver or copper electrodes plus additives and insulation layers. Each application gets a tailored stack rather than a catalogue part.

The first case study is an anti-icing heater, 300 by 300 millimetres, coated on PET at 48 volts, targeting sheet resistance of around 55 ohms per square. Infrared imaging measured three spots from corner to corner to confirm uniform heat distribution across the whole surface.

Across a large production batch of roughly 600 heaters at identical dimensions, every unit stayed within plus or minus five degrees Celsius of the target. Spot measurements landed within plus or minus two degrees Celsius of the initial value β€” a direct demonstration of electrical uniformity, and the repeatability industrial production actually requires.

In this short video, you can learn:
* Ink formulation, printed pattern and architecture are adjusted together to reach 3 to 480 volts, 0.01 to 6 watts per square centimetre and 200 degrees Celsius peak.
* A 300 by 300 millimetre anti-icing heater on PET ran at 48 volts against a sheet resistance target of around 55 ohms per square.
* Across about 600 production heaters, all units stayed within plus or minus five degrees Celsius of target, with infrared spot checks within plus or minus two degrees Celsius.

πŸ“‹ **Clip Abstract** Volume data from roughly 600 anti-icing heaters, 300 by 300 millimetres on PET at 48 volts with a 55 ohm per square target, shows every unit within plus or minus five degrees Celsius of target. Infrared checks at three corner-to-corner spots fell within plus or minus two degrees Celsius, demonstrating the electrical uniformity required for industrial repeatability.

About the speaker:
* Speaker: Anaghim Nasri
* Company: BLACKLEAF
* Event: Electronics RESHAPED 2026 | Berlin
* Location: Estrel, Berlin

USA: The Future of Electronics RESHAPED | USA
πŸ“… Save the date: 9 and 10 June 2027
πŸ“ Mountain View, California (Silicon Valley)
πŸ“‹ Info: https://www.techblick.com/electronicsreshapedusa

Europe
The Future of Electronics RESHAPED | Berlin
πŸ“… Save the date: 20 and 21 October 2027
πŸ“ Berlin, Germany
πŸ“‹ Info: https://www.techblick.com/electronicsreshaped

#GrapheneInk, #PrintedHeaters, #AntiIcingHeater, #SheetResistance, #PrintedElectronics, #FlexibleElectronics


About this talk

β†’ Engineering Water-Based Graphene Inks for Scalable Printed Heating Systems Β· Anaghim Nasri Β· The Future of Electronics RESHAPED 2026 Berlin


Other talks by Anaghim Nasri

More Snippets
CONTACT US

KGH Concepts GmbH

Mergenthalerallee 73-75, 65760, Eschborn

+49 17661704139

admin@techblick.com

TechBlick is owned and operated by KGH Concepts GmbH

Registration number HRB 121362

VAT number: DE 337022439

  • LinkedIn
  • YouTube

Sign up for our newsletter to receive updates on our latest speakers and events AND to receive analyst-written summaries of the key talks and happenings in our events.

Thanks for submitting!

© 2026 by KGH Concepts GmbH

bottom of page