top of page

Ashutosh Kumar

Polar Light Technologies

* All members of the platform can watch the entire presentation.

 

Please register to become a member.

Ashutosh Kumar | Polar Light Technologies: How does template-assisted bottom-up pyramidal growth eliminate etching damage and achieve sub-Lambertian microLED emission?

05:25 - 07:53

Other snippets from this talk

Summary of the clip:

How does template-assisted bottom-up pyramidal growth eliminate etching damage and achieve sub-Lambertian microLED emission?

The approach grows InGaN/GaN LED structures as bottom-up pyramids using template-assisted selective-area growth. The template defines pyramid positions, so the layout can adapt to commercially available CMOS backplanes; for a 12-micron-pitch backplane, the growth mask places microLEDs at 12-micron separation. Because pyramids are grown on side planes, no etching is involved, leaving the material system inherently damage-free and improving optical performance.

All work uses standard MOCVD, so any pilot line or fab with MOCVD can reproduce these microLED structures. The pyramid geometry produces focused, narrow light emission, described as a sub-Lambertian lobe. This matters for microdisplays: conventional planar LEDs lose many photons, while the pyramid’s narrow lobe concentrates useful light. Calculations at 520 nm, close to green, showed about 50% of light within ±20%.

Conventional LEDs generate many photons that are not useful and become heat and power dissipation. The narrow pyramidal emission reduces that problem to a large extent. The narrow emission is also cited as 58% within ±20%, compared with the earlier 50% figure at 520 nm. The key claim is that geometry improves extracted useful photons without etching damage.

In this short video, you can learn:
* Template-assisted selective-area growth aligns pyramid microLEDs to CMOS backplane pitch, e.g. 12 microns, without etching.
* Standard MOCVD can reproduce the InGaN/GaN pyramidal microLED structures in pilot lines or fabs.
* Pyramid geometry yields a narrow sub-Lambertian lobe, with cited 50% at 520 nm and 58% within ±20%, reducing heat and power dissipation.

📋 **Clip Abstract** This clip describes InGaN/GaN bottom-up pyramidal microLEDs grown by template-assisted selective-area growth, allowing mask pitch to match CMOS backplanes such as 12 microns. It reports that avoiding etching leaves the material inherently damage-free, that standard MOCVD enables reproducible fab/pilot-line growth, and that the pyramid geometry gives focused sub-Lambertian emission with cited 50% at 520 nm and 58% within ±20%, reducing wasted photons, heat and power dissipation.

About the speaker:
* Speaker: Ashutosh Kumar
* Company: Polar Light Technologies
* Event: nnovation Festival: Additive, Printed, Sustainable Electronics, MicroLEDs and AR/VR Displays, Perovskites | July 2026
* Location: Online Platform

Annual access to our onsite event(s), all online events and a library featuring over 1800 presentations (recordings + PDF) across all our onsite and onsite events and technology areas. Join us and over 2000 members from around the world now.
Explore and join now --> https://www.techblick.com/

#InGaNGaN, #TemplateAssistedGrowth, #MOCVD, #SubLambertianEmission, #MicroLEDDisplays, #ARDisplays

This is a highlight of the presentation:

Pyramidal microLEDs in the same material system paving the way for RGB emission in micro displays

Innovation Festival: Additive, Printed, Sustainable Electronics

Innovation Festival: MicroLEDs and AR/VR Displays

46213

Online Platform

Organised By:

TechBlick

TechBlick and MicroLED Industry Association

More Highlights from the same talk.

12:32 - 14:26

Can sub-micron LEDs reach 460 nm, and what limits their CMOS backplane integration?

Can sub-micron LEDs reach 460 nm, and what limits their CMOS backplane integration?

Last year’s result was a proof of concept: sub-micron micro LEDs within 500 nanometer, called nano LEDs, with devices produced down to 460 nanometer. That established that the solution is not limited to micron sizes and can reach sub-micron dimensions. Integration depends on finding a CMOS backplane that can handle those small sizes.

The driver for smaller sub-pixels is better resolution and cost control. The transcript notes a need to go with smaller sub-pixels. If a suitable CMOS backplane becomes available, the LEDs can be integrated. Until then, availability of the CMOS backplane is the limiting factor for scaling into sub-micron arrays.

A dual-color display project with Finetech is now public, funded under Eurostar. The collaboration uses the micro LED platform on the front side; Finetech helps with flip-chip bonding. The aim is a dual-color integrable display on a CMOS backplane by the end of next year.

In this short video, you can learn:
* Sub-micron micro LEDs were produced down to 460 nanometer as a proof of concept, called nano LEDs.
* CMOS backplane availability is the limiting factor for integrating sub-micron LEDs.
* A Eurostar-funded project with Finetech aims for a dual-color integrable display on CMOS by the end of next year.

📋 **Clip Abstract** Sub-micron nano LEDs produced down to 460 nanometer show micro LED scaling beyond micron sizes, but CMOS backplane availability limits integration. A dual-color display collaboration with Finetech, funded under Eurostar, targets flip-chip bonding and an integrable display on CMOS by the end of next year.

About the speaker:
* Speaker: Ashutosh Kumar
* Company: Polar Light Technologies
* Event: nnovation Festival: Additive, Printed, Sustainable Electronics, MicroLEDs and AR/VR Displays, Perovskites | July 2026
* Location: Online Platform

Annual access to our onsite event(s), all online events and a library featuring over 1800 presentations (recordings + PDF) across all our onsite and onsite events and technology areas. Join us and over 2000 members from around the world now.
Explore and join now --> https://www.techblick.com/

#SubMicronNanoLED, #CMOSBackplane, #FlipChipBonding, #DualColorDisplay, #MicroLEDDisplays, #NanoLEDArrays


About this talk

→ Pyramidal microLEDs in the same material system paving the way for RGB emission in micro displays · Ashutosh Kumar · TechBlick Innovations Festival July 2026

More Snippets
CONTACT US

KGH Concepts GmbH

Mergenthalerallee 73-75, 65760, Eschborn

+49 17661704139

admin@techblick.com

TechBlick is owned and operated by KGH Concepts GmbH

Registration number HRB 121362

VAT number: DE 337022439

  • LinkedIn
  • YouTube

Sign up for our newsletter to receive updates on our latest speakers and events AND to receive analyst-written summaries of the key talks and happenings in our events.

Thanks for submitting!

© 2026 by KGH Concepts GmbH

bottom of page