Benjamin King & Jon Harwell | University of Glasgow | REACT Centre: Can printed zinc circuits on paper dissolve in vinegar, recover components, and beat alternatives in life-cycle assessment?
02:46 - 04:41
Other snippets from this talk
Summary of the clip:
Can printed zinc circuits on paper dissolve in vinegar, recover components, and beat alternatives in life-cycle assessment?
The ultra-disposable project targeted circuits that are as biodegradable as possible, accepting that biodegradable construction restricts the materials available. Elemental zinc was chosen as the conductor, and the process prints zinc with high conductivity onto paper, polycaprolactone and even chocolate. Resolution reached the low microns, showing the approach can pattern fine features on substrates ranging from biodegradable polymer to paper.
A paper-based device with mounted components was placed in 2% acetic acid, essentially vinegar, and disintegrated over a few minutes. The components were recovered and remained totally fine, with no measurable performance change after recycling. This demonstrates a disposable format where the circuit substrate breaks down while functional parts are retrieved for reuse.
Life cycle assessment showed the paper-based device comes out better, with a particular end-of-life advantage when used as compost. In that compost route, the net impact can become negative. The discussion then moves toward slightly higher-end performance work, distinguishing the ultra-disposable biodegradable circuit approach from the next performance tier.
In this short video, you can learn:
* Elemental zinc can be printed with high conductivity on paper, polycaprolactone and chocolate, reaching low-micron resolution.
* A paper device disintegrates in 2% acetic acid within minutes, after which mounted components are recovered with no measurable performance change.
* Life cycle assessment favors the paper-based device and shows negative net impact when it is composted at end of life.
π **Clip Abstract** The ultra-disposable circuit work uses printed elemental zinc on biodegradable substrates such as paper and polycaprolactone, reaching low-micron resolution. A paper-based device disintegrates in 2% acetic acid so components can be recovered unchanged, and life cycle assessment shows a better outcome with negative net impact under composting.
About the speakers:
* Speakers: Benjamin King, Jon Harwell
* Company: University of Glasgow | REACT Centre
* Event: Sustainable Electronics RESHAPED 2026 | Berlin
* Location: Estrel, Berlin
Sustainable Electronics RESHAPED | Berlin
π
Save the date: 20 and 21 October 2027
π Berlin, Germany
π Info: https://www.techblick.com/sustainableelectronicsreshaped
#PrintedZinc, #BiodegradablePolycaprolactone, #PaperSubstrates, #ComponentRecovery, #SustainableElectronics, #LifeCycleAssessment
This is a highlight of the presentation:
Sustainable Electronic Materials for Wireless: Advanced Packaging to E-Textiles
More Highlights from the same talk.
01:25 - 02:50
Can a hemp-fibre PCB be recycled in boiling water without sacrificing RF performance below 1 GHz?
Can a hemp-fibre PCB be recycled in boiling water without sacrificing RF performance below 1 GHz?
The recycling premise starts with boards designed for recovery rather than disposal. Jiva Materials replaces FR4βa fibreglass composite that produces a hazardous end productβwith hemp-fibre circuit boards. Placed in boiling water, the hemp-fibre board slowly decomposes and falls apart, making component recovery much easier. The demonstration shows the board under boiling water, then separating, which simplifies reclaiming parts.
FR4 is widely used partly for high-frequency performance, and the team has RF testing expertise for these alternatives. Hemp-fibre materials contain quite a lot of water by nature, so they are not as good as FR4 at ultra-high frequency. Still, their performance and loss tangent are acceptable as long as operation stays below the gigahertz regime.
Most applications do not need ultra-high-frequency capability, but people remain interested in it. For those cases, the trade-off is explicit: design for recycling can recover components while staying within acceptable performance and loss tangent below the gigahertz regime. The work moves from design for recycling toward materials that degrade without causing an end-of-life catastrophe when recycling is not realistic.
In this short video, you can learn:
* Jiva Materials' hemp-fibre boards decompose in boiling water so components are easier to recover.
* FR4 is a fibreglass composite that produces a hazardous end product.
* Hemp-fibre boards are not as good as FR4 at ultra-high frequency but acceptable below the gigahertz regime.
π **Clip Abstract** Hemp-fibre circuit boards designed for recycling decompose in boiling water, making component recovery easier than with FR4 fibreglass composites. RF testing shows higher water content limits ultra-high-frequency performance, yet loss tangent and performance remain acceptable below the gigahertz regime.
About the speakers:
* Speakers: Benjamin King, Jon Harwell
* Company: University of Glasgow | REACT Centre
* Event: Sustainable Electronics RESHAPED 2026 | Berlin
* Location: Estrel, Berlin
Sustainable Electronics RESHAPED | Berlin
π
Save the date: 20 and 21 October 2027
π Berlin, Germany
π Info: https://www.techblick.com/sustainableelectronicsreshaped
#HempFibrePCB, #BoilingWaterRecycling, #LossTangent, #FR4Replacement, #RFMaterials, #SustainableElectronics
06:34 - 08:16
Can liquid-metal e-textile antennas be recycled over 95% and redeployed from 400 MHz to 2.4 GHz?
Can liquid-metal e-textile antennas be recycled over 95% and redeployed from 400 MHz to 2.4 GHz?
The electronic-textile work uses liquid metals: small tubes are filled with liquid metal, plugged, and incorporated into antennas for high-frequency communications. The liquid-metal tracks can be stitched directly into wearable devices. This gives a route to high-frequency textile antennas while keeping the metal track as a removable component at end of life.
At end of life, the tracks are removed and placed in a lightly alkaline solution, which removes the liquid metal from the tubes. This allows recovery of the tracks and, eventually, recovery of the liquid metals. A colleague, Jiaxuan, ran recycling experiments on these liquid-metal antennas and found that over 95% of the liquid-metal tracks could be recycled.
The recovered materials were redeployed in a range of different antennas operating between 400 MHz and 2.4 GHz, demonstrating circularity and reuse. Antenna-performance results for reused and redeployed devices showed negligible performance losses from recycling the antennas for different designs. The team then moved away from liquid metal to examine other materials.
In this short video, you can learn:
* Liquid-metal tracks can be stitched into wearable antennas and later removed at end of life.
* A lightly alkaline solution strips liquid metal from tubes, enabling track and metal recovery.
* Over 95% of liquid-metal tracks were recycled, and recovered materials were redeployed in 400 MHzβ2.4 GHz antennas with negligible performance loss.
π **Clip Abstract** Liquid-metal tubes are plugged and incorporated into high-frequency e-textile antennas that can be stitched into wearables and removed at end of life. A lightly alkaline solution enables recovery of over 95% of the tracks, and recovered materials were redeployed in 400 MHzβ2.4 GHz antennas with negligible performance loss.
About the speakers:
* Speakers: Benjamin King, Jon Harwell
* Company: University of Glasgow | REACT Centre
* Event: Sustainable Electronics RESHAPED 2026 | Berlin
* Location: Estrel, Berlin
Sustainable Electronics RESHAPED | Berlin
π
Save the date: 20 and 21 October 2027
π Berlin, Germany
π Info: https://www.techblick.com/sustainableelectronicsreshaped
#LiquidMetalAntennas, #ETextileRecycling, #AlkalineMetalRecovery, #RedeployedAntennas, #SustainableElectronics, #WearableWireless
04:41 - 06:01
Can additive copper deliver 13 Β΅m RF lines and void-free 25:1 through-glass vias without vacuum?
Can additive copper deliver 13 Β΅m RF lines and void-free 25:1 through-glass vias without vacuum?
The work moves from biodegradability to additively manufactured high-performance components, specifically copper transmission lines. A 13-micron resolution is achieved, which is enough for a βfancyβ RF transmission line. The process can run on any substrate; in polyimide, the tracks are embedded inside the polymer, making them very scratch-resistant and durable while delivering very good attenuation loss.
The same techniques feed through-glass via fabrication. Glass substrates are being pursued for very large panels that can incorporate dyes, and vias through the glass are needed to connect solder balls on the other side. Historically these vias are filled with copper or another metal, and void-free filling has been very difficult, normally requiring high-impact methods such as ultra-high vacuum.
A low-impact, solution-based process has been developed instead. It achieves void-free filling on devices with a 25-to-one aspect ratio, avoiding the ultra-high-vacuum route. The approach is framed as a way to fill through-glass vias for large glass panels, connecting solder balls on the other side without the historical high-impact, void-free filling difficulty.
In this short video, you can learn:
* Copper transmission lines were additively made at 13-micron resolution and embedded in polyimide for scratch resistance, durability and very good attenuation loss.
* Through-glass vias for large glass panels must be void-free filled to connect solder balls, which historically required copper or metal filling and ultra-high-vacuum methods.
* A low-impact, solution-based process achieved void-free filling at a 25-to-one aspect ratio.
π **Clip Abstract** Additive copper transmission lines reach 13-micron resolution on any substrate, with tracks embedded in polyimide for durability and very good attenuation loss. The same techniques support through-glass via fabrication, where a low-impact, solution-based process achieves void-free filling at a 25-to-one aspect ratio, unlike historical ultra-high-vacuum metal-filling methods.
About the speakers:
* Speakers: Benjamin King, Jon Harwell
* Company: University of Glasgow | REACT Centre
* Event: Sustainable Electronics RESHAPED 2026 | Berlin
* Location: Estrel, Berlin
Sustainable Electronics RESHAPED | Berlin
π
Save the date: 20 and 21 October 2027
π Berlin, Germany
π Info: https://www.techblick.com/sustainableelectronicsreshaped
#AdditiveCopperTransmissionLines, #ThroughGlassViaFilling, #EmbeddedPolyimideTracks, #VoidFree25To1, #AdvancedPackaging, #AdditiveElectronics
Links to this speaker's talk page and other highlights appear here.


