Blake Martin | Sofab Inks: Can a C60-free ETL hold efficiency and lifetime at 900 cm² module scale?
08:01 - 10:21
Other snippets from this talk
Summary of the clip:
Can a C60-free ETL hold efficiency and lifetime at 900 cm² module scale?
Spin coating has been a relative challenge for these metal oxide ETLs, attributed to the high vapor pressure of the systems, which makes uniform coatings over wider areas difficult. Yet the spin-coating gap is misleading: as module areas grow and the process controls and equipment used become more robust and more industry-standard, the efficiency delta between C60 and these materials narrows.
At scale the headline result is 22.2% in a 900 cm² module, positioned as evidence that the technique and materials hold up beyond the spin-coating stage gate routinely used to judge viability. Work with industry partners such as APS is framed as de-risking the route to scale.
Durability is where the case is made: in 85/85 dark testing the metal oxide modules retain 87% of efficiency at 500 hours against 74% for a C60 control, and dark heat testing shows 81% retention over 10,000 hours. Light-heat stability remains the ongoing development target.
In this short video, you can learn:
* 22.2% efficiency was demonstrated in a 900 cm² module, narrowing the gap to C60 as area and process robustness increase.
* In 85/85 dark testing the materials retained 87% efficiency at 500 hours versus 74% for the C60 control.
* Dark heat testing reached 81% retention over 10,000 hours, with light-heat stability still under development.
📋 **Clip Abstract** Metal oxide ETLs struggle in spin coating because of high vapor pressure, so the meaningful comparison sits at module scale, where a 900 cm² device reached 22.2%. Durability carries the fullerene-free case — 87% versus 74% at 500 hours in 85/85 dark and 81% over 10,000 hours dark heat — while light-heat stability remains under development.
About the speaker:
* Speaker: Blake Martin
* Company: Sofab Inks
* Event: Perovskite Connect 2026 | Berlin
* Location: Estrel, Berlin
Save the date: Perovskite Connect 2027 | 20 and 21 OCT 2027 | Berlin
Co-located with the Future of Electronics RESHAPED conference and exhibition
Learn more: https://www.techblick.com/perovskiteconnect
Intestered in exhibiting: learn more here: https://www.techblick.com/perovskiteconnect
#MetalOxideETL, #FullereneFreeETL, #900cm2Module, #DampHeatTesting, #PerovskitePhotovoltaics, #SolarModuleReliability
This is a highlight of the presentation:
A Fullerene-Free Future: Advances In Metal Oxide ETLs
21 and 22 OCT 2026
Estrel, Berlin
Organised By:
More Highlights from the same talk.
04:05 - 06:09
What are the real per-watt price floors perovskite modules face in US versus global markets?
What are the real per-watt price floors perovskite modules face in US versus global markets?
The global spot floor for perovskite modules sits at around $0.10 per watt, but that is below cash cost for many producers. Overcapacity in the broader solar market keeps prices low. Shutting down a line costs more than running through the trough, so lines keep running until some silicon manufacturers ultimately go belly up.
Around $0.15 to $0.20 per watt is what many speculate is the sustainable margin band, where stable production volumes exist and where crystalline silicon likely has a stable floor to manufacture at. That remains a speculative number to date.
The US or domestic envelope is higher: a medium module price for a US procured module is about $0.28 per watt once delivered to the US. Fully US-made cells sit around $0.46 per watt. That premium largely exists for tariffs, financial incentives, and cost savings with robust supply chains. Buyers weigh system level costs, not just module per dollars.
In this short video, you can learn:
* The global spot floor of about $0.10 per watt is below cash cost for many producers, sustained by overcapacity and the fact that shutting a line costs more than running through the trough.
* Many speculate a sustainable margin band of $0.15 to $0.20 per watt, tied to stable production volumes and a likely crystalline silicon manufacturing floor.
* US delivered medium module prices reach about $0.28 per watt, while fully US-made cells sit around $0.46 per watt; buyers weigh system level costs, not module dollars alone.
📋 **Clip Abstract** Perovskite modules face a landscape of price points, not one number to beat, dictated by where you sell and for what application. The global spot floor sits near $0.10 per watt, a speculative sustainable margin band is $0.15 to $0.20 per watt, and US delivered modules reach about $0.28 per watt versus $0.46 per watt for fully US-made cells.
About the speaker:
* Speaker: Blake Martin
* Company: Sofab Inks Inc.
* Event: nnovation Festival: Additive, Printed, Sustainable Electronics, MicroLEDs and AR/VR Displays, Perovskites | July 2026
* Location: Online Platform
Annual access to our onsite event(s), all online events and a library featuring over 1800 presentations (recordings + PDF) across all our onsite and onsite events and technology areas. Join us and over 2000 members from around the world now.
Explore and join now --> https://www.techblick.com/
#PerovskitePricing, #GlobalSpotFloor, #USModulePremium, #SiliconOvercapacity, #SolarManufacturing, #PVEconomics
02:25 - 04:08
What makes C60 the weak interface, and how can a printable tin oxide replace it?
What makes C60 the weak interface, and how can a printable tin oxide replace it?
C60 is described as the weakest interface in a perovskite cell, and the goal is to remove it from modules. That is technically challenging because the replacement is coated directly on top of perovskite. Perovskite is thermally unstable and sensitive to different solvents and deposition techniques, which filters out many viable materials for this interface.
The layer underneath the perovskite has its own instability issues, spanning the whole transport layer. Nickel oxide SAM layers with HTL are noted as popular in the community. Under thermal stresses, some anchoring molecules can loosen and introduce instability in the module, so the underlayer is not a passive constraint on the C60 replacement.
The C60 replacement is tin oxide nanoparticle material. The surface of tin oxide nanoparticles is functionalized to make them soluble in solvents that enable solution-phase coating directly on top of the perovskite film. These are alcohol-based systems with low-temperature anneals and scalable coating techniques compatible primarily with blade coating and slot-die coating.
In this short video, you can learn:
* C60 is attributed as the weakest interface in a perovskite cell, motivating its removal from modules.
* Coating directly onto perovskite is constrained by thermal instability and sensitivity to solvents and deposition techniques.
* Functionalized tin oxide nanoparticles are soluble in alcohol-based systems, allow low-temperature anneals, and are compatible with blade and slot-die coating.
📋 **Clip Abstract** The talk frames C60 as the weakest interface in a perovskite cell and explains why replacing it is difficult: the replacement must be coated directly onto thermally unstable perovskite that is sensitive to solvents and deposition techniques. It presents functionalized tin oxide nanoparticles in alcohol-based systems for solution-phase coating directly on perovskite, with low-temperature anneals and compatibility with blade and slot-die coating.
About the speaker:
* Speaker: Blake Martin
* Company: Sofab Inks
* Event: Perovskite Connect 2026 | Berlin
* Location: Estrel, Berlin
Save the date: Perovskite Connect 2027 | 20 and 21 OCT 2027 | Berlin
Co-located with the Future of Electronics RESHAPED conference and exhibition
Learn more: https://www.techblick.com/perovskiteconnect
Intestered in exhibiting: learn more here: https://www.techblick.com/perovskiteconnect
#TinOxideNanoparticles, #C60Replacement, #SolutionPhaseCoating, #SlotDieCoating, #PerovskiteSolarCells, #MetalOxideETL
12:17 - 14:17
Which two ETL layers drive 60% of perovskite subcell cost, and can solution processing cut it?
Which two ETL layers drive 60% of perovskite subcell cost, and can solution processing cut it?
The electron transport layer carries the bulk of perovskite cost, dominated by C60 and ALD tin oxide. Those two layers alone account for roughly 60% of perovskite subcell cost. The vacuum route for these two steps contributes almost three cents per watt; substituting solution-coated replacements can reduce manufacturing cost to less than one cent per watt, assuming three gigawatts of capacity.
Because the baseline is three gigawatts, the savings are magnified under the subscale assumptions being examined. Eliminating those two problematic materials is where the business positions itself in the ecosystem, targeting the processing levers and material selections that move module cost most.
A solution-processable tin oxide electron transport layer has demonstrated 22.3% at a 30 by 30 centimetre squared module area, approaching a world record at the time, with certification underway. In accelerated thermal stability tests it maintains 80% efficiency over 10,000 hours, roughly ten times the rate at which C60 degraded. It replaces the evaporated C60 step.
In this short video, you can learn:
* C60 and ALD tin oxide account for roughly 60% of perovskite subcell cost.
* Solution-coated replacements cut the vacuum route's almost three cents per watt below one cent per watt at three gigawatts.
* Solution-processable tin oxide hit 22.3% at 30 by 30 cm² and held 80% efficiency over 10,000 hours.
📋 **Clip Abstract** C60 and ALD tin oxide account for roughly 60% of perovskite subcell cost, with the vacuum route adding nearly three cents per watt. Solution-coated replacements drop that below one cent per watt at three gigawatts, while a solution-processable tin oxide module reached 22.3% at 30 by 30 cm².
About the speaker:
* Speaker: Blake Martin
* Company: Sofab Inks Inc.
* Event: nnovation Festival: Additive, Printed, Sustainable Electronics, MicroLEDs and AR/VR Displays, Perovskites | July 2026
* Location: Online Platform
Annual access to our onsite event(s), all online events and a library featuring over 1800 presentations (recordings + PDF) across all our onsite and onsite events and technology areas. Join us and over 2000 members from around the world now.
Explore and join now --> https://www.techblick.com/
#C60Replacement, #TinOxideETL, #SolutionProcessedETL, #PerovskiteThermalStability, #PerovskiteSolarCells, #Photovoltaics
About this talk
→ A Fullerene-Free Future: Advances In Metal Oxide ETLs · Blake Martin · Perovskite Connect 2026
Other talks by Blake Martin
- What will perovskite modules actually cost? Pricing pressure, sensitivity, and levers that matter · TechBlick Innovations Festival July 2026
- Novel materials for next-generation perovskite solar panel production processes · The Future of Electronics RESHAPED 2025
More highlights from Blake Martin
- ▶ What are the real per-watt price floors perovskite modules face in US versus global markets? · Innovation Festival: Additive, Printed, Sustainable Electronics
- ▶ Which two ETL layers drive 60% of perovskite subcell cost, and can solution processing cut it? · Innovation Festival: Additive, Printed, Sustainable Electronics
- ▶ Why does a mere 5-year drop in perovskite solar cell lifetime completely destroy its economic viability? · Perovskite Connect 2025
- ▶ Can functionalized metal oxide nanoparticles eliminate the open-circuit voltage pinning that plagues fullerene-based perovskites? · Perovskite Connect 2025
- ▶ How do we stop perovskite solar modules from physically delaminating along laser scribe lines during thermal stress? · Perovskite Connect 2025


