top of page

Chantal Paquet

National Research Council Canada

* All members of the platform can watch the entire presentation.

 

Please register to become a member.

Chantal Paquet | National Research Council Canada: How does switching from a vat to a polymer coating enable 40-micron resolution in 3D printed electronics?

09:08 - 11:16

Other snippets from this talk

Summary of the clip:

How does switching from a vat to a polymer coating enable 40-micron resolution in 3D printed electronics?

The move away from a bulk resin vat, replacing it with a polymer coating, is the core process change. Higher concentration in the coating raises polymerization rate and suppresses blurring. Accuracy against the ideal print line improves across a wide range of feature sizes, reaching 40 microns β€” the pixel size. Sheet resistance lands at about 50 micro ohms per square, which is typical for electroplated material.

The infinity loop is the demonstration part: a complex geometry that would be difficult to print with nozzle-based techniques. Because the object rotates while light is projected onto it, there is no shadowing and no standoff distance. The finished loop carries a printed conductive circuit on its curved surface β€” the capability it was chosen to demonstrate.

Building up the circuit means repeating that cycle: functional polymer printed and plated, a dielectric layer added, then functional polymer and copper plating again, giving a metal-insulator-metal stack on a curved surface. Today's dielectric layers are still flat, and more complex dielectric geometry is the stated next step. That is the gap between a curved metal-insulator-metal stack and a fully three-dimensional multi-layer circuit.

In this short video, you can learn:
* Replacing the resin vat with a polymer coating allows a higher concentration that increases polymerization rate and minimizes blurring.
* Print accuracy now holds over a wide range of feature sizes down to 40 microns, the pixel size, with sheet resistance of about 50 micro ohms per square.
* Rotating the object during projection removes shadowing and standoff distance, letting conductive circuits, dielectric layers and metal-insulator-metal stacks be printed on curved surfaces.

πŸ“‹ **Clip Abstract** Dropping the resin vat for a polymer coating raises the concentration that drives polymerization, cutting blur and lifting print accuracy to 40-micron features with sheet resistance near 50 micro ohms per square. The same rotating-projection approach prints conductive and dielectric layers into a metal-insulator-metal stack on a curved infinity loop, with more complex dielectric geometry as the next step.

About the speaker:
* Speaker: Chantal Paquet
* Company: National Research Council Canada
* Event: The Future of Electronics RESHAPED 2025
* Location: Estrel, Berlin

πŸ—“οΈ Save the date for the next Future of Electronic RESHAPED conference and exhibition
USA | Mountain View | 9-10 June 2027 : https://www.techblick.com/electronicsreshapedusa
Europe | Berlin | 20-21 October 2027: https://www.techblick.com/electronicsreshaped

#PolymerCoatingPrinting, #MetalInsulatorMetalStack, #SheetResistance, #NozzleFreeDeposition, #PrintedElectronics, #AdditiveManufacturing

This is a highlight of the presentation:

3D electronics with volumetric additive manufacturing

The Future of Electronics RESHAPED 2025 | Berlin

​

22-23 October 2025

Estrel, Berlin

Organised By:

TechBlick

​

More Highlights from the same talk.

04:13 - 05:57

How does tomographic volumetric additive manufacturing (VAM) eliminate layer artifacts and print 3D objects in seconds?

How does tomographic volumetric additive manufacturing (VAM) eliminate layer artifacts and print 3D objects in seconds?

Standoff distance limits the shapes you could access; a good example is concave shapes. The approach here is different, based on tomographic additive manufacturing, also known as VAM. This method came out in May 2019. You use a light projector and project light patterns onto a rotating vial of photo resin. As the vial rotates and you project light, enough light dose accumulates in certain areas, allowing you to solidify, trigger polymerization and solidify your object.

This method has gained traction because it is extremely fast compared to other 3D printing techniques. You can print things in seconds. You don't need support structures. Because you're printing all at once, there's no layer artifact, so you have a very smooth finish. In real time, you'll see the object appear as you're seeing it right now.

During the real-time demonstration, the object appears as the rotating vial receives projected light patterns. The accumulated light dose in certain areas triggers polymerization, solidifying the object. A little benchy boat was fabricated in 16 seconds. We have been working on this since more or less the beginning of the introduction. This method is tomographic additive manufacturing, also known as VAM.

In this short video, you can learn:
* Tomographic additive manufacturing projects light patterns onto a rotating vial of photo resin, accumulating enough light dose in certain areas to trigger polymerization and solidify the object.
* Because the object is printed all at once, VAM avoids layer artifacts and support structures while producing a smooth finish and print times in seconds.
* A little benchy boat was fabricated in 16 seconds, and the method has been worked on since more or less the beginning of its introduction.

πŸ“‹ **Clip Abstract** Tomographic additive manufacturing, also known as VAM, projects light patterns onto a rotating vial of photo resin; accumulated light dose triggers polymerization and solidifies the object. It is extremely fast, needs no support structures, and because printing happens all at once, it avoids layer artifacts, yielding a smooth finish; a benchy boat was fabricated in 16 seconds.

About the speaker:
* Speaker: Chantal Paquet
* Company: National Research Council Canada
* Event: The Future of Electronics RESHAPED 2025
* Location: Estrel, Berlin

πŸ—“οΈ Save the date for the next Future of Electronic RESHAPED conference and exhibition
USA | Mountain View | 9-10 June 2027 : https://www.techblick.com/electronicsreshapedusa
Europe | Berlin | 20-21 October 2027: https://www.techblick.com/electronicsreshaped

#TomographicVAM, #PhotoResinVial, #LightDosePolymerization, #BenchyIn16Seconds, #AdditiveManufacturing, #3DPrinting

00:00:33 - 00:01:52

Can we completely eliminate support structures and layer lines in 3D printing?

Can we completely eliminate support structures and layer lines in 3D printing?

Tomographic Additive Manufacturing, often referred to as Volumetric Additive Manufacturing (VAM), represents a paradigm shift from traditional layer-by-layer 3D printing. By utilizing a digital light processing (DLP) projector to cast dynamic light patterns onto a rotating vial of photosensitive resin, the technique constructs entire 3D geometries simultaneously rather than sequentially. This parallel light exposure triggers localized polymerization only within specific voxels where the cumulative light dose crosses the threshold.

The primary advantages of this volumetric approach lie in speed, surface quality, and structural freedom. Because the entire object is printed concurrently within a self-supporting resin medium, there is no need for sacrificial support structures. This eliminates the tedious post-processing steps typical of stereolithography (SLA) or fused deposition modeling (FDM) methods.

Furthermore, the absence of discrete layering means the finished parts are free from staircase artifacts, resulting in exceptionally smooth surfaces. This makes the technology highly appealing for microfluidics, bioprinting, and optical components like lenses, where surface roughness directly impacts performance.

In this short video, you can learn:
* How dynamic light patterns and rotating vials achieve volumetric polymerization.
* Why volumetric printing eliminates the need for sacrificial support structures.
* The technical benefits of a layerless finish for optics and microfluidics.

πŸ“‹ **Clip Abstract** This clip introduces Tomographic Additive Manufacturing (VAM) and explains how projecting 3D light patterns into a rotating photo-resin vial allows for rapid, support-free printing. Chantal Paquet highlights its advantages, including the elimination of layer artifacts to produce ultra-smooth surface finishes.

#VolumetricAdditiveManufacturing, #Tomographic3DPrinting, #VolumetricPolymerization, #Layerless3DPrinting, #PrecisionOptics, #Microfluidics

07:15 - 09:08

How can volumetric additive manufacturing be used to create templates for copper plating on 3D objects?

How can volumetric additive manufacturing be used to create templates for copper plating on 3D objects?

The approach uses volumetric additive manufacturing to print a functional polymer onto a 3D object. That printed polymer acts as a template for copper plating. The resin is simple: a crosslinker and a functional monomer. After printing and processing, the functional monomer coordinates with silver. The silver is then reduced to silver nanoparticles, which seed copper plating. This links printed 3D geometry to metallization, making the functional polymer the key material for introducing electronics to 3D shapes.

In the first generation, the sample was simply placed in a large vial of photo resin and printed. This required low photo concentrations so light could penetrate the whole resin volume. Because those concentrations were low, polymerization rates were slow, causing diffusion and blurring of features. The team still succeeded: they printed a polymer template on a test pattern and then copper plated it. Compared with the target, the measured line width showed printing but not high accuracy, with about 400 microns line resolution.

After reviewing the results, the team realized they did not need a big vat of resin. This insight matters because the vat geometry and low photo concentration forced slow polymerization, which limited resolution. The target pattern, middle printed polymer, and copper-plated sample show the concept works, but the right-hand plot reveals deviation from perfect print accuracy. The measured line width versus target and the approximately 400-micron line resolution define the first-generation process window that volumetric additive manufacturing must improve.

In this short video, you can learn:
* A crosslinker and functional monomer photo resin can be volumetrically printed, processed to coordinate with silver, reduce silver to nanoparticles, and seed copper plating.
* Printing in a large vial of photo resin required low photo concentrations for light penetration, which slowed polymerization and caused diffusion and blurring, limiting feature accuracy.
* First-generation templates achieved about 400 microns line resolution; measured line width versus target showed printing was possible but not terribly accurate, prompting the realization that a big resin vat was unnecessary.

πŸ“‹ **Clip Abstract** Volumetric additive manufacturing can print a functional polymer template that coordinates with silver, reduces to silver nanoparticles, and seeds copper plating on 3D objects. First-generation printing in a large vial required low photo concentrations, causing slow polymerization and feature blurring, with about 400 microns line resolution and only moderate accuracy.

About the speaker:
* Speaker: Chantal Paquet
* Company: National Research Council Canada
* Event: The Future of Electronics RESHAPED 2025
* Location: Estrel, Berlin

πŸ—“οΈ Save the date for the next Future of Electronic RESHAPED conference and exhibition
USA | Mountain View | 9-10 June 2027 : https://www.techblick.com/electronicsreshapedusa
Europe | Berlin | 20-21 October 2027: https://www.techblick.com/electronicsreshaped

#VolumetricAdditiveManufacturing, #FunctionalPolymerTemplate, #SilverNanoparticleSeeding, #CopperPlating, #3DElectronics, #AdditiveElectronics


About this talk

β†’ 3D electronics with volumetric additive manufacturing Β· Chantal Paquet Β· The Future of Electronics RESHAPED 2025


Other talks by Chantal Paquet


More highlights from Chantal Paquet

More Snippets
CONTACT US

KGH Concepts GmbH

Mergenthalerallee 73-75, 65760, Eschborn

+49 17661704139

admin@techblick.com

TechBlick is owned and operated by KGH Concepts GmbH

Registration number HRB 121362

VAT number: DE 337022439

  • LinkedIn
  • YouTube

Sign up for our newsletter to receive updates on our latest speakers and events AND to receive analyst-written summaries of the key talks and happenings in our events.

Thanks for submitting!

© 2026 by KGH Concepts GmbH

bottom of page