Chris Booher | ChemCubed: How does an inkjet multilayer process create vias without drilling, etching, or lamination?
13:55 - 15:37
Other snippets from this talk
Summary of the clip:
How does an inkjet multilayer process create vias without drilling, etching, or lamination?
Traditional multilayer FR4 builds laminate cores, etch copper, relaminate core, and laminate foil with each layer. The inkjet route instead uses an inkjet printer and lets you select the substrate: rigid FR4 for printing on rigid components, flexible film, or Kapton polyimide, or even the board itself using dielectric ink. It starts with a grounding layer printed into the board substrate, demonstrated here on thin FR4.
The next layer would traditionally be a drill-hole layer. Here the process is reciprocal: dielectric is printed, with no print where the drill holes would be, so a no print becomes the via or drill-hole point. Then the next conductive layer is printed on top of the dielectric and printed through those vias to connect to the previous grounding layer or printed circuits underneath.
That produces a 2-layer circuit board. Solder mask can then be printed on top, or the board can go to a different solder-mask process. The example is a digitally printed custom 2-layer board. There is no limit to the number of layers; 20 layers have been done easily. This avoids the traditional drill, etch, and lamination sequence for vias and multilayer build-up.
In this short video, you can learn:
* A dielectric no-print replaces the drill-hole layer, so the absence of ink defines the via location.
* The next conductive layer prints through those vias to connect to the previous grounding layer or printed circuits.
* The demonstrated digitally printed custom board is 2 layers, with solder mask printable on top, and 20 layers have been done easily.
📋 **Clip Abstract** Inkjet multilayer printing selects rigid FR4, flexible film, Kapton polyimide, or a dielectric-printed board, starting with a grounding layer. It uses a reciprocal dielectric no-print as the via, then prints the next conductor through it, yielding a digitally printed custom 2-layer board with no layer-count limit demonstrated to 20 layers.
About the speaker:
* Speaker: Chris Booher
* Company: ChemCubed
* Event: Printed, Flexible, Hybrid & InMold Electronics 2021
* Location: Online
Join TechBlick - the home of printed electronics, additive electronics, hybrid electronics, sustainable electronics
https://www.techblick.com/
#InkJetMultilayer, #DielectricNoPrintVia, #PrintedGroundingLayer, #PrintedSolderMask, #AdditiveManufacturedElectronics, #PrintedElectronics
This is a highlight of the presentation:
Multi-material /Multi-layer Solutions for Additively Manufactured Electronics/ Printed Electronics (AME/PE)
More Highlights from the same talk.
02:11 - 03:03
How fast can a particle-free silver ink reach full conductivity at 80°C, and how does higher temperature change it?
How fast can a particle-free silver ink reach full conductivity at 80°C, and how does higher temperature change it?
The conductive inks described are particle-free silver inks, positioned as the highest-performing silver conductive ink in the market. Their best-in-class conductive performance is near bulk conductivity of silver. The same material also shows unmatched sintering efficiency: it can sinter as low as 80°C for full conductive performance in as little as 5 minutes.
Sintering efficiency also applies at higher temperatures. Anything upwards of 100°C is mainly a matter of seconds. At temperatures between 130°C and 160°C, sintering is virtually instantaneous. This gives a clear temperature ladder from the 80°C, five-minute full-conductivity result to second-scale and near-instantaneous outcomes, using the same particle-free silver conductive ink.
The materials are offered in several different formats for different inkjet capabilities, including the Electrojet brand. That format flexibility matters because the sintering claims are tied to particle-free silver conductive ink performance, not just a single printhead or process configuration. The clip frames the value as best-in-class conductivity near bulk silver plus sintering at 80°C in five minutes, then faster at higher temperatures.
In this short video, you can learn:
* The particle-free silver conductive ink is described as delivering best-in-class conductivity near bulk silver.
* It can sinter at 80°C to full conductive performance in as little as 5 minutes.
* At 100°C and above sintering is mainly seconds, and from 130°C to 160°C it is virtually instantaneous.
📋 **Clip Abstract** A particle-free silver conductive ink is presented as best-in-class, with conductivity near bulk silver and sintering at 80°C for full conductive performance in as little as 5 minutes. The same sintering efficiency scales to higher temperatures—seconds above 100°C and virtually instantaneous from 130°C to 160°C—with formats for different inkjet capabilities including Electrojet.
About the speaker:
* Speaker: Chris Booher
* Company: ChemCubed
* Event: Printed, Flexible, Hybrid & InMold Electronics 2021
* Location: Online
Join TechBlick - the home of printed electronics, additive electronics, hybrid electronics, sustainable electronics
https://www.techblick.com/
#ParticleFreeSilverInk, #LowTemperatureSintering, #BulkSilverConductivity, #ElectrojetInkjet, #PrintedElectronics, #AdditiveManufacturing
20:27 - 21:21
How thick is one silver layer, and how close is its resistivity to bulk silver?
How thick is one silver layer, and how close is its resistivity to bulk silver?
The first question asked for the thickness of one cured silver layer and its resistance. The answer is not a single fixed number: thickness depends on the printer technology and the deposition technology used. With this particular printer at standard resolution—among many available settings—one silver layer measures around 2 to 3 microns in the z-direction.
Resistivity also depends on the quality of the image being printed. The demonstrated result reaches as good as up to 2.0×10⁻⁸ ohm-meters of bulk resistivity with a very good, high-quality print. That figure is presented as the best achieved, not as a fixed value for every printed layer.
Both numbers therefore come with qualifications. The 2–3 micron thickness is specific to the printer and its standard-resolution settings, not a universal layer specification. The 2.0×10⁻⁸ ohm-meters result is tied to a high-quality image. For engineers, the practical takeaway is to treat silver layer thickness and resistivity as deposition- and print-quality-dependent parameters that must be measured for the chosen process.
In this short video, you can learn:
* One silver layer on the referenced printer is about 2 to 3 microns thick in the z-direction at standard resolution.
* Silver ink thickness is dependent on printer and deposition technology, with multiple settings available.
* A best-case bulk resistivity of up to 2.0×10⁻⁸ ohm-meters was demonstrated with a very good high-quality print.
📋 **Clip Abstract** The clip answers a direct materials question: one silver layer is around 2 to 3 microns thick in the z-direction on the referenced printer at standard resolution, though thickness depends on printer and deposition technology. It also reports resistivity dependent on image quality, with a demonstrated best result as good as up to 2.0×10⁻⁸ ohm-meters of bulk resistivity for a very good high-quality print.
About the speaker:
* Speaker: Chris Booher
* Company: ChemCubed
* Event: Printed, Flexible, Hybrid & InMold Electronics 2021
* Location: Online
Join TechBlick - the home of printed electronics, additive electronics, hybrid electronics, sustainable electronics
https://www.techblick.com/
#SilverConductiveInk, #ZDirectionalThickness, #BulkResistivity, #HighQualityPrint, #AdditiveManufacturingElectronics, #PrintedElectronics
16:23 - 18:07
Where does printed dielectric still fall short of FR4 in strength, reflow, and flexibility?
Where does printed dielectric still fall short of FR4 in strength, reflow, and flexibility?
On materials, the presenter flags structural limits: FR4 board is very strong structurally, and the dielectric ink has limitations at this time when replacing an FR4 board by printing one. High-temperature tolerance is the second gap — FR4 is flame resistant, and under high-temperature solder reflow the dielectric may not be a suitable solution, though low-temperature alternatives exist.
Process temperature adds a constraint: the dielectric inks need to be printed at a cooler temperature, so the platen must actually be cooled down before dielectrics can be printed — solutions are pending. On flexibility, the high-performing particle-free conductor inks lack the resins and fillers that make stretchable inks on the marketplace flexible; solutions are claimed there too.
Printer-side gaps are acknowledged too: there is currently no optical alignment in the process, though it is being looked into. Sequence automation is named as a further limitation before the clip closes. The gaps are framed across materials, printer and processes — unmet needs recognized not only for this technology but across the additive manufacturing industry.
In this short video, you can learn:
* FR4 board remains structurally stronger than the dielectric ink used to print a replacement board.
* High-temperature solder reflow can exceed dielectric ink capability, pointing instead to low-temperature alternatives.
* Dielectrics must be printed on a cooled platen, and the process currently has no optical alignment.
📋 **Clip Abstract** The talk sorts additive electronics gaps into materials, printer and processes. Dielectric strength, reflow tolerance, print temperature, conductor stretchability and missing optical alignment are each named, with pending or alternative solutions.
About the speaker:
* Speaker: Chris Booher
* Company: ChemCubed
* Event: Printed, Flexible, Hybrid & InMold Electronics 2021
* Location: Online
Join TechBlick - the home of printed electronics, additive electronics, hybrid electronics, sustainable electronics
https://www.techblick.com/
#DielectricInk, #SolderReflow, #ParticleFreeInk, #OpticalAlignment, #AdditiveManufacturing, #PrintedElectronics
About this talk
→ Multi-material /Multi-layer Solutions for Additively Manufactured Electronics/ Printed Electronics (AME/PE) · Chris Booher · Printed, Flexible, Hybrid, & InMold Electronics 2021


