Christoph Kaiser | Leibniz-Institute for New Materials: Can silver flakes with carbon sliding contacts survive 50,000 stretch cycles at 10% strain where pure silver degrades?
03:13 - 05:33
Other snippets from this talk
Summary of the clip:
Can silver flakes with carbon sliding contacts survive 50,000 stretch cycles at 10% strain where pure silver degrades?
When the stretchable ink is stretched, the particles move apart, lose contact and the ink’s conductivity breaks down. The approach enriches silver flakes with small carbon particles that act as sliding contacts when particles are pulled apart, enabling continuous contact between the flakes themselves.
A benchmark compared non-hybrid pure silver flakes, a silver-and-carbon formulation, and an additional formulation based on a silicone matrix, alongside a PU matrix material and commercially available inks. Printing followed datasheet instructions for commercial inks and the ink setup feature for the developed inks, to test whether an improvement existed.
The test applied 50,000 stretch cycles at 10% strain. Pure flakes showed resistivity increasing over longer-term cycles and still increasing. The hybrid flake-and-particle approach was well improved: an initial drop occurred, but it saturated pretty well and resistivity did not really rise a lot over many cycles.
In this short video, you can learn:
* Carbon particles between silver flakes act as sliding contacts that maintain continuous contact as stretching pulls particles apart.
* The benchmark compared pure silver, silver-and-carbon, silicone-matrix, PU-matrix and commercial inks under stretch testing.
* At 50,000 cycles and 10% strain, hybrid inks showed an initial resistivity drop that saturated, while pure flakes kept increasing.
📋 **Clip Abstract** The clip explains how carbon particles create sliding contacts between silver flakes, preserving conductivity as stretchable inks separate. A benchmark of pure silver, hybrid, matrix and commercial inks under 50,000 cycles at 10% strain shows hybrid resistivity saturating while pure flakes continue increasing.
About the speaker:
* Speaker: Christoph Kaiser
* Company: Leibniz-Institute for New Materials
* Event: Electronic Textiles RESHAPED 2026 | Berlin
* Location: Estrel, Berlin
Electronic Textiles RESHAPED 2027 | Berlin
📅 Save the date: 20 and 21 October 2027
📍 Berlin, Germany
📋 Info: https://www.techblick.com/electronictextilesreshaped
#SilverFlakeInk, #CarbonSlidingContacts, #StretchCycleTesting, #ResistivitySaturation, #StretchableElectronics, #PrintedElectronics
This is a highlight of the presentation:
Stretchable Electronics for Textiles and Beyond
More Highlights from the same talk.
07:01 - 09:08
Can one stretchable ink both heat and sense temperature while stretch and thermal expansion barely shift its thermoelectric coefficient?
Can one stretchable ink both heat and sense temperature while stretch and thermal expansion barely shift its thermoelectric coefficient?
The thermoelectric coefficient is governed mainly by the conductive particles themselves, not by the stretched state. In the diagram, the coefficients are pretty much the same for each stretched state. Using these ink formulations as a conductive paste and a temperature-generating ink paste, with the layout known from PTC inks, stretching produced barely any change in temperature.
On textile, the ink was integrated with TPU hot melt, and the result was more or less the same: no real temperature change due to the stretched state. The thermal expansion can be overcome, and the thermoelectric coefficient mainly relies on the underlying conductive material itself. Varying the mixture of carbon particles and silver flakes sets the overall thermoelectric coefficient, over a rather broad range.
Beyond generating temperature, the same material can measure temperature. This is shown by a demonstrator done by the company FlexTime, which was shown at the last LOPEC. There, this ink was used to generate a spatially distributed measurement that can be used for monitoring of battery cell applications.
In this short video, you can learn:
* Stretching barely changes the temperature of these conductive and temperature-generating inks, and the thermoelectric coefficient is pretty much the same for each stretched state.
* Integrating the ink on textile with TPU hot melt showed no real temperature change due to the stretched state.
* Varying carbon particles and silver flakes sets the thermoelectric coefficient over a broad range, enabling both temperature generation and spatially distributed temperature measurement.
📋 **Clip Abstract** Stretchable thermoelectric inks are shown to keep their thermoelectric coefficient across stretched states, with the conductive particles dominating the coefficient and thermal expansion overcome. The same formulations act as conductive and temperature-generating pastes, integrate on textile with TPU hot melt, and support both heating and spatially distributed temperature measurement, including a FlexTime battery-cell monitoring demonstrator shown at LOPEC.
About the speaker:
* Speaker: Christoph Kaiser
* Company: Leibniz-Institute for New Materials
* Event: Electronic Textiles RESHAPED 2026 | Berlin
* Location: Estrel, Berlin
Electronic Textiles RESHAPED 2027 | Berlin
📅 Save the date: 20 and 21 October 2027
📍 Berlin, Germany
📋 Info: https://www.techblick.com/electronictextilesreshaped
#ThermoelectricInk, #TemperatureGeneratingPaste, #TPUHotMelt, #SpatiallyDistributedMeasurement, #StretchableElectronics, #ElectronicTextiles
09:25 - 11:51
Why does direct printing on textile fail, and how does planarization enable safe body-near heating with temperature sensing?
Why does direct printing on textile fail, and how does planarization enable safe body-near heating with temperature sensing?
The traditional route prints the structure on TPU and laminates it to fabric with a hot-melt foil; this works out pretty well. Direct printing onto textile also works, but the woven texture brings hills and valleys, and those topography steps generate cracks in the printed layer. The surface roughness, not the printing itself, is what degrades the structure.
The fix is a planarization coating: a cheap material, chosen from its measured metrics, is coated onto the textile so it soaks into the fabric and levels the surface. The actual sensor or heater structures are then printed on top and see more or less the same conditions as if they had been printed directly on TPU.
The distinctive feature is combining heating with temperature measurement in one system. A heated jacket is forgiving, you switch it off and open it; heated leggings against the body are not. With real temperature measurement inside the system the heating can be controlled, so body-near heating does not risk burning wearers — and 42 to 43 °C sustained on skin is already enough to burn.
In this short video, you can learn:
* Direct printing on textile works, but the hills and valleys of the weave generate cracks unless the surface is planarized first.
* A cheap coating material soaked into the textile levels it, giving printed structures the same conditions as printing on TPU.
* Combining heating with in-system temperature measurement is what makes body-near heated garments safe, because 42 to 43 °C over time on skin already burns.
📋 **Clip Abstract** Textile integration works either by printing on TPU and laminating with hot-melt foil, or by printing directly on fabric, where weave texture generates cracks. A cheap planarization coating soaked into the textile restores TPU-like printing conditions, and pairing heaters with in-system temperature sensing keeps body-near heating below burn thresholds.
About the speaker:
* Speaker: Christoph Kaiser
* Company: Leibniz-Institute for New Materials
* Event: Electronic Textiles RESHAPED 2026 | Berlin
* Location: Estrel, Berlin
Electronic Textiles RESHAPED 2027 | Berlin
📅 Save the date: 20 and 21 October 2027
📍 Berlin, Germany
📋 Info: https://www.techblick.com/electronictextilesreshaped
#TextilePlanarization, #HotMeltFoilLamination, #PrintedHeaters, #BodyNearTemperatureSensing, #StretchableElectronics, #SmartTextiles
About this talk
→ Stretchable Electronics for Textiles and Beyond · Christoph Kaiser · Electronic Textiles RESHAPED 2026 Berlin


