Corne Rentrop | TracXon: Can printed electronics realistically target 10% of the $102 billion PCB market?
14:16 - 15:56
Other snippets from this talk
Summary of the clip:
Can printed electronics realistically target 10% of the $102 billion PCB market?
The proposal is a dot on the horizon: replace 10% of PCBs, a $102 billion market in 2026. Fully integrated roll-to-roll printing reduces production steps and opens new design possibilities. Additive manufacturing is already discussed, and double-sided SMD assembly can be done in one step. The capabilities are already here.
Typical substrates are PET, PEI and polycarbonate; stretchables move to TPU. Qualified inks are available for graphics, electrics, carbon and silver. Silver also allows more aggressive recycling properties in printed electronics. These material and ink capabilities are already there for roll-to-roll printed electronics.
Component assembly can go down to 0201 and further. Mini-LEDs are already appearing, transparent electronics are possible, and true and blind vias can be created. The via technology is patented. That patented via fabrication is part of the roll-to-roll flexible hybrid electronics capability.
In this short video, you can learn:
* The target is replacing 10% of a $102 billion PCB market in 2026.
* PET, PEI, polycarbonate and TPU substrates are named alongside qualified graphics, electrics, carbon and silver inks.
* Assembly reaches 0201 and beyond, with mini-LEDs, transparent electronics, and patented true and blind vias.
π **Clip Abstract** The clip frames a 10% PCB replacement goal against a $102 billion 2026 market. It cites roll-to-roll printing, PET/PEI/polycarbonate/TPU substrates, qualified carbon and silver inks, 0201 assembly, mini-LEDs, transparent electronics and patented true and blind vias as capabilities already present.
About the speaker:
* Speaker: Corne Rentrop
* Company: TracXon
* Event: Electronics RESHAPED 2026 | Berlin
* Location: Estrel, Berlin
USA: The Future of Electronics RESHAPED | USA
π
Save the date: 9 and 10 June 2027
π Mountain View, California (Silicon Valley)
π Info: https://www.techblick.com/electronicsreshapedusa
Europe
The Future of Electronics RESHAPED | Berlin
π
Save the date: 20 and 21 October 2027
π Berlin, Germany
π Info: https://www.techblick.com/electronicsreshaped
#RollToRollPrinting, #DoubleSidedSMDAssembly, #BlindViaFabrication, #SilverInkRecycling, #FlexibleHybridElectronics, #PrintedElectronics
This is a highlight of the presentation:
Scaling Roll-to-Roll Flexible Hybrid Electronics: From Patented VIA Fabrication to Mainstream Manufacturing
More Highlights from the same talk.
08:45 - 10:28
How does a roll-to-roll via process cut four print steps to two while improving durability?
How does a roll-to-roll via process cut four print steps to two while improving durability?
Vias are created on a roll from a simple foil covered by a protective foil. Vias are shot into that protective foil, filled by dispensing silver, cured to conduct, then the cover foil is removed. Materials, vias and fiducials are known before printing; conductor is printed on one side, the web flipped, and the other side printed.
The via approach simplifies production. Normally a conductor is printed, then an isolator, which tends to form pinholes and is printed twice to prevent pinholes at the same location, then circuitry, then components. This is reduced to basically two print steps: four print steps become two.
Because the substrate itself with the via becomes the isolator, durability is much higher and it is a better product in that sense. After assembling what cannot be printedβchips, LEDs and solar cellsβthe products are created as they are, with printing on both sides of the foil.
In this short video, you can learn:
* Vias are shot into a protective foil, filled by dispensing silver, and cured so they conduct.
* Replacing printed isolators with the substrate and via cuts production from four print steps to two.
* The via-based substrate acts as the isolator, which raises durability and yields a better product.
π **Clip Abstract** Roll-to-roll via fabrication shoots vias into a protective foil, dispenses silver to fill them, cures the silver, and removes the cover foil before printing both sides of the web. The substrate-plus-via replaces a twice-printed isolator, reducing four print steps to two and improving durability before chips, LEDs and solar cells are assembled.
About the speaker:
* Speaker: Corne Rentrop
* Company: TracXon
* Event: Electronics RESHAPED 2026 | Berlin
* Location: Estrel, Berlin
USA: The Future of Electronics RESHAPED | USA
π
Save the date: 9 and 10 June 2027
π Mountain View, California (Silicon Valley)
π Info: https://www.techblick.com/electronicsreshapedusa
Europe
The Future of Electronics RESHAPED | Berlin
π
Save the date: 20 and 21 October 2027
π Berlin, Germany
π Info: https://www.techblick.com/electronicsreshaped
#RollToRollVias, #SilverViaFilling, #ProtectiveFoilVias, #FourToTwoPrintSteps, #FlexibleHybridElectronics, #PrintedElectronics
16:09 - 17:11
Why does pilot production demand 10,000β100,000 samples before any business is made?
Why does pilot production demand 10,000β100,000 samples before any business is made?
R&D institutes typically deliver the prototype and the proof of concept; that proof of concept must be functional, doing what it can do, to attract industry attention and show whether industry can benefit from it. After that stage, pilot production begins.
Pilot production is a tough step because it is usually done to run client certification tests, where TRL7 and TRL8-like technology appears, along with customer satisfaction and field trials in the medical field. Those tests already demand 10,000 to 100,000 samples.
So you already need a factory at that point, and you do not make business yet. What is provided is the capability to set up the line and to do it on a large scale, spanning custom circuitry and the manufacturing processes around it.
In this short video, you can learn:
* The proof of concept must be functional first, because pilot production only starts once industry has seen what the prototype can do.
* Client certification tests at TRL7 and TRL8-like maturity already consume ten thousand to one hundred thousand samples.
* A pilot line has to be set up and run at large scale during that sample-heavy phase, before any business is made.
π **Clip Abstract** The route runs from a functional proof of concept, delivered by R&D institutes, into pilot production. Pilot production is where certification tests, medical field trials and TRL7/TRL8 samples β 10,000 to 100,000 of them β come off a line that is not yet making business.
About the speaker:
* Speaker: Corne Rentrop
* Company: TracXon
* Event: Electronics RESHAPED 2026 | Berlin
* Location: Estrel, Berlin
USA: The Future of Electronics RESHAPED | USA
π
Save the date: 9 and 10 June 2027
π Mountain View, California (Silicon Valley)
π Info: https://www.techblick.com/electronicsreshapedusa
Europe
The Future of Electronics RESHAPED | Berlin
π
Save the date: 20 and 21 October 2027
π Berlin, Germany
π Info: https://www.techblick.com/electronicsreshaped
#PilotProductionSampling, #ClientCertificationTests, #TRL7TRL8Samples, #ProofOfConceptPrototyping, #FlexibleHybridElectronics, #PrintedElectronics
10:45 - 12:15
Why does accessing a chipβs ground plane require double-sided printed vias?
Why does accessing a chipβs ground plane require double-sided printed vias?
Double-sided printing enables more complex features, including a device printed on both sides. Around the chip the layout becomes crowded because many fan-outs leave the chip, yet the ground plane still must be accessed. The DXF shows the routing constraint: the bottom side can be used to exit downward, freeing space on the other sides of the chip for fan-out.
This is a complicated construction, but some applications really require vias and cannot function without them. The drone controller example was made by removing the drone and controller and replicating them in a printed electronics form factor. According to the talk, only through the vias could this be done, with lightweight defense offering many applications.
The next step described is to move even further: not only vias but also printed components. That direction builds on the same double-sided via capability, where bottom-side exits reduce crowding around chips and preserve fan-out room. The clip frames vias as enabling, not optional, for applications that cannot operate without them.
In this short video, you can learn:
* Double-sided printing lets a bottom-side exit access the chip ground plane and free space for fan-out around a crowded chip.
* The DXF illustrates the routing constraint that makes vias necessary for some applications.
* A drone controller was replicated in a printed electronics form factor, which the talk says was possible only through vias.
π **Clip Abstract** Double-sided printing is used to access a chipβs ground plane by exiting from the bottom side, freeing room around crowded fan-out. The clip presents a printed drone controller as an application that cannot function without vias, and points to printed components as the next step beyond vias.
About the speaker:
* Speaker: Corne Rentrop
* Company: TracXon
* Event: Electronics RESHAPED 2026 | Berlin
* Location: Estrel, Berlin
USA: The Future of Electronics RESHAPED | USA
π
Save the date: 9 and 10 June 2027
π Mountain View, California (Silicon Valley)
π Info: https://www.techblick.com/electronicsreshapedusa
Europe
The Future of Electronics RESHAPED | Berlin
π
Save the date: 20 and 21 October 2027
π Berlin, Germany
π Info: https://www.techblick.com/electronicsreshaped
#DoubleSidedVias, #ChipGroundPlane, #FanOutRouting, #PrintedDroneController, #FlexibleHybridElectronics, #AdditiveElectronics
About this talk
β Scaling Roll-to-Roll Flexible Hybrid Electronics: From Patented VIA Fabrication to Mainstream Manufacturing Β· Corne Rentrop Β· The Future of Electronics RESHAPED 2026 Berlin
Other talks by Corne Rentrop
- Sustainable Mass-production of Hybrid Printed Electronics Β· TechBlick Innovations Festival | Free-To-Attend 2024


