top of page

Dave Rice

TactoTek

* All members of the platform can watch the entire presentation.

 

Please register to become a member.

Dave Rice | TactoTek: How do you encapsulate printed and surface-mounted electronics inside a single-piece 3D injection-molded part?

07:48 - 09:51

Other snippets from this talk

Summary of the clip:

How do you encapsulate printed and surface-mounted electronics inside a single-piece 3D injection-molded part?

An IMSE part cannot be exploded after processing: it is a single-piece injection-molded unit. Electronics—printed electronics and surface-mounted components—can sit on the A surface, the underside of the cosmetic surface, or on the top side of a film at the bottom of the part, or both. Components are surface-mounted on films, typically IML films, and also on natural materials such as wood veneer; injection molding then encapsulates them in plastics.

The most popular structural alternative, for a number of reasons, is a two-film structure. Most typically, the B-film—an in-mold labeling film—is the electronics carrier, while the A-film is the cosmetic surface. This makes it easier to achieve a beautiful piano black finish without witness lines from the printed electronics. Parts with electronics mounted on the underside of the A-film are similarly beautiful and are reflected in the middle structure.

The alternatives include a B-film with just resin. Construction choices put electronics on the A surface, on the top side of a bottom film, or both; the two-film configuration separates cosmetic A-film from electronics-carrying B-film. The middle structure shows electronics on the underside of the A-film, while the B-film-plus-resin alternative is noted without further detail.

In this short video, you can learn:
* An IMSE part is a single-piece injection-molded unit that cannot be exploded after processing.
* In a two-film structure, the B-film is most typically the in-mold labeling electronics carrier and the A-film is the cosmetic surface.
* Surface-mounted components can be placed on IML films or natural materials such as wood veneer before injection molding encapsulates the electronics in plastics.

📋 **Clip Abstract** IMSE parts are single-piece injection-molded units in which printed electronics and surface-mounted components can be placed on the A surface, on the top side of a bottom film, or both before injection molding encapsulates them in plastics. The most popular two-film structure typically uses an in-mold labeling B-film as the electronics carrier and an A-film as the cosmetic surface, enabling a piano black finish without witness lines from printed electronics.

About the speaker:
* Speaker: Dave Rice
* Company: TactoTek
* Event: Printed, Flexible, Hybrid & InMold Electronics 2021
* Location: Online

Join TechBlick - the home of printed electronics, additive electronics, hybrid electronics, sustainable electronics
https://www.techblick.com/

#IMSE, #TwoFilmStructure, #PianoBlackFinish, #SurfaceMountComponents, #InMoldElectronics, #PrintedElectronics

This is a highlight of the presentation:

Realizing Smart Surfaces with In-Mold Electronics

Printed, Flexible, Hybrid & InMold Electronics 2021

​

10-11 March 2021

Online

Organised By:

TechBlick

​

More Highlights from the same talk.

10:02 - 12:00

Why surface-mount LEDs and circuitry while the film is flat, before thermoforming, rather than after?

Why surface-mount LEDs and circuitry while the film is flat, before thermoforming, rather than after?

IMSE parts combine printed electronics and chip-based electronics inside three-dimensional injection-molded plastics. The production sequence has four primary steps: print decoration on the cosmetic surface if needed, print electronics as multiple circuitry layers where required, surface-mount components while the film remains flat, and thermoform the functional film into a 3D shape. LEDs of different types are added for illumination features in about 95% of parts.

Doing this in two dimensions matters because two-dimensional pick-and-place equipment is globally available, relatively inexpensive, extremely fast and highly accurate. That enables efficient scaling as production expands. The electronics film is fully functional before thermoforming, but design know-how must locate components and maintain electrical integrity as the part transforms from a 2D shape to a 3D shape.

The sequence keeps the IMSE electronics fully functional before thermoforming, then transforms the flat film into a 3D shape. Design know-how is required to locate components and maintain electrical integrity during that transformation. The flat-film approach uses globally available two-dimensional pick-and-place equipment, which is relatively inexpensive, extremely fast and highly accurate, enabling efficient scaling as production expands. Surface-mount LEDs provide illumination in about 95% of parts.

In this short video, you can learn:
* IMSE production has four primary steps: decoration printing, electronics printing, flat-film surface mounting and thermoforming.
* Two-dimensional pick-and-place is globally available, relatively inexpensive, extremely fast and highly accurate, enabling efficient production scaling.
* Design know-how must locate components and maintain electrical integrity as the film transforms from 2D to 3D, with LEDs used in about 95% of parts.

📋 **Clip Abstract** The clip outlines four primary IMSE production steps and explains why circuitry and LEDs are surface-mounted while the film is still flat. It argues that globally available two-dimensional pick-and-place offers relatively low cost, high speed, high accuracy and efficient scaling, while design know-how preserves electrical integrity through thermoforming.

About the speaker:
* Speaker: Dave Rice
* Company: TactoTek
* Event: Printed, Flexible, Hybrid & InMold Electronics 2021
* Location: Online

Join TechBlick - the home of printed electronics, additive electronics, hybrid electronics, sustainable electronics
https://www.techblick.com/

#IMSESurfaceMounting, #TwoDimensionalPickAndPlace, #ThermoformedCircuitry, #LEDIlluminationFeatures, #PrintedElectronics, #InMoldElectronics

17:34 - 19:33

Why do capacitive touch and antennas both work better when buried in the part's structural surface?

Why do capacitive touch and antennas both work better when buried in the part's structural surface?

Underneath every IMSE part is a material stack, and the supplier's job is confirming those materials work together effectively. On that foundation the functional capabilities are built: touch, and specifically very responsive capacitive touch, enabled by the very close proximity of the point of touch to the sensor. Proximity sensors and multiple styles of illumination follow, all of them using in-mold LEDs.

Wireless connectivity and antennas perform extremely well for a similar reason: they sit in the surface structure of the part, removed from other sources of signal interference. Look and feel matter too, since most parts are cosmetic; yet an increasing number of use cases exploit the environmental protection of the electronics to place IMSE in hidden locations.

The demonstrator held up on screen contains two styles of illumination: a single capacitive button, backlit in the middle, with dynamic illumination associated with it, plus a slider control that goes around a recessed center ring and is a group of capacitive sensors. These fundamental building blocks can be assembled very simply.

In this short video, you can learn:
* Placing the sensor directly beneath the point of touch is what makes IMSE capacitive touch so responsive.
* Antennas built into the part's surface structure sit away from other signal interference sources, so wireless connectivity performs extremely well.
* One demonstrator combined two illumination styles with a backlit capacitive button and a recessed-ring capacitive slider.

📋 **Clip Abstract** IMSE performance rests on a validated material stack carrying capacitive touch, proximity sensing, in-mold LED illumination and antennas. Touch and wireless both gain from physical placement — sensors close to the touch point, antennas isolated in the surface structure — while the demonstrator shows a backlit button and recessed-ring slider assembled from those blocks.

About the speaker:
* Speaker: Dave Rice
* Company: TactoTek
* Event: Printed, Flexible, Hybrid & InMold Electronics 2021
* Location: Online

Join TechBlick - the home of printed electronics, additive electronics, hybrid electronics, sustainable electronics
https://www.techblick.com/

#InMoldLEDs, #CapacitiveSlider, #AntennaSignalIsolation, #BacklitCapacitiveButton, #SmartSurfaces, #InMoldElectronics

13:38 - 15:57

What does replacing a 64-part conventional control panel with one molded part actually save?

What does replacing a 64-part conventional control panel with one molded part actually save?

The IMSE overhead control panel uses 3.5 mm plastics and weighs 200 grams. Tooling includes one expensive injection mold with the same cost structure as any injection mold, plus relatively inexpensive forming and film trimming tools because it is film insert molding. Third parties have tested such parts against standard automotive interior qualifications, including damp heat, thermal shock, and aging.

A conventional overhead control panel design had 64 parts, requiring extensive assembly and over 15 costly tools, and it ended up heavy. The IMSE alternative is a seamless smart molded structure: one molded part and a small external PCBA for system electronics. This delivers a 90% thickness reduction and a 58% mass reduction while preserving design differentiation and brand language.

Compared with the 64-part conventional assembly, IMSE cuts total cost of ownership by 25%. It avoids designing, tooling, sourcing, transporting, inventorying, and assembling all those eliminated parts. The result is one molded part plus a small external PCBA for system electronics, with a 35% reduction in greenhouse gases.

In this short video, you can learn:
* The IMSE part uses 3.5 mm plastics and weighs 200 grams, with one expensive injection mold plus relatively inexpensive forming and film trimming tools.
* A 64-part conventional overhead control panel becomes one molded part and a small external PCBA, producing 90% thickness and 58% mass reductions.
* IMSE cuts total cost of ownership by 25% and greenhouse gases by 35% while eliminating design, tooling, sourcing, transport, inventory, and assembly of removed parts.

📋 **Clip Abstract** A 64-part conventional overhead control panel is compared with an IMSE alternative made as one molded part plus a small external PCBA. The IMSE structure uses 3.5 mm plastics, weighs 200 grams, passes automotive interior damp heat, thermal shock, and aging tests, and reports 90% lower thickness, 58% lower mass, 25% lower total cost of ownership, and 35% lower greenhouse gases.

About the speaker:
* Speaker: Dave Rice
* Company: TactoTek
* Event: Printed, Flexible, Hybrid & InMold Electronics 2021
* Location: Online

Join TechBlick - the home of printed electronics, additive electronics, hybrid electronics, sustainable electronics
https://www.techblick.com/

#InMoldElectronics, #FilmInsertMolding, #OverheadControlPanel, #DampHeatTesting, #PrintedElectronics, #AutomotiveInteriors


About this talk

→ Realizing Smart Surfaces with In-Mold Electronics · Dave Rice · Printed, Flexible, Hybrid, & InMold Electronics 2021

More Snippets
CONTACT US

KGH Concepts GmbH

Mergenthalerallee 73-75, 65760, Eschborn

+49 17661704139

admin@techblick.com

TechBlick is owned and operated by KGH Concepts GmbH

Registration number HRB 121362

VAT number: DE 337022439

  • LinkedIn
  • YouTube

Sign up for our newsletter to receive updates on our latest speakers and events AND to receive analyst-written summaries of the key talks and happenings in our events.

Thanks for submitting!

© 2026 by KGH Concepts GmbH

bottom of page