top of page

David McDougall

HB Fuller

* All members of the platform can watch the entire presentation.

 

Please register to become a member.

David McDougall | HB Fuller: Why are EVA and POE problematic for perovskite encapsulation, and what replaces them?

06:01 - 07:58

Other snippets from this talk

Summary of the clip:

Why are EVA and POE problematic for perovskite encapsulation, and what replaces them?

EVA has been the encapsulant standard for 25 years and is still used by almost all crystalline manufacturers, but inside the perovskite community it is almost a no-go. Exposure to water creates acetic acid over time, and that acid is not good. EVA can also have high moisture vapor transmission rates, so water permeates rather easily, with other side effects adding to the challenge.

POE, polyolefin, seems to be the alternative, but polyolefin uses catalysts that are nasty to the perovskite; they can impact durability and shorten the life cycle. A thermoplastic polyolefin—a material that melts and solidifies repeatedly—is becoming the material of choice. It works at lower temperatures, processable as low as 90 degrees Celsius if necessary, and development work with lower molecular weight polymer chains may push that even lower.

The thermoplastic route still has issues with recrystallization after cure as it cools, which the speaker says could be a paper by itself. Encapsulant thickness is tunable: for space applications where weight matters, it can be 100 microns thick; where hail impact or mechanical durability matters, it can go as high as 600, maybe 700 microns, and anything in between.

In this short video, you can learn:
* EVA's water-driven acetic acid formation and high moisture vapor transmission make it almost a no-go for perovskite modules.
* POE's catalysts are nasty to perovskite and can shorten durability and life cycle, prompting thermoplastic polyolefin as the alternative.
* Thermoplastic polyolefin can process as low as 90 degrees Celsius, though recrystallization after cooling remains an issue, and thickness spans 100 microns for space to 600 or 700 microns for hail durability.

📋 **Clip Abstract** EVA's 25-year crystalline-silicon dominance does not transfer to perovskites because water exposure generates acetic acid and its high moisture vapor transmission lets water permeate. POE brings catalysts that are nasty to perovskite, so thermoplastic polyolefin is emerging as the choice—processable at 90 degrees Celsius, tunable from 100 to 600–700 microns, with recrystallization after cooling still unresolved.

About the speaker:
* Speaker: David McDougall
* Company: HB Fuller
* Event: Perovskite Connect 2026 | Berlin
* Location: Estrel, Berlin

Save the date: Perovskite Connect 2027 | 20 and 21 OCT 2027 | Berlin
Co-located with the Future of Electronics RESHAPED conference and exhibition
Learn more: https://www.techblick.com/perovskiteconnect

Intestered in exhibiting: learn more here: https://www.techblick.com/perovskiteconnect

#EVAEncapsulant, #ThermoplasticPolyolefin, #AceticAcidFormation, #EncapsulantThickness, #PerovskiteModules, #SolarCellEncapsulation

This is a highlight of the presentation:

Materials for Perovskite Modules

​

​

21 and 22 OCT 2026

Estrel, Berlin

Organised By:

​

​

More Highlights from the same talk.

01:05 - 02:19

Why does standard PV lamination at 140–160°C threaten perovskite modules and bankability?

Why does standard PV lamination at 140–160°C threaten perovskite modules and bankability?

The standard module is a glass, encapsulant, interconnect, active-cell and wire stack, covered by another encapsulant sheet and another glass sheet. These layers are laminated together at about 140 to 160 degrees Celsius, with vacuum and pressure applied and other stresses to the stack. This temperature is described as far too hot for what the perovskite community can handle.

After lamination, junction boxes, frames and other parts are assembled. The finished module still must meet standards, specifically IEC 61215 and UL 2703, plus other criteria, to enable bankability. The transcript also notes IEC 61215-1-6, described as a standard being initiated for perovskites under the IEC commission, with its status unknown.

The clip frames standard PV lamination as a sequence of temperature, vacuum and pressure stresses on the whole stack, not a single step. It contrasts that established architecture with the hope that some processes and materials may be very attractive going forward. The bankability requirement remains tied to meeting IEC 61215, UL 2703 and other criteria.

In this short video, you can learn:
* Standard module lamination at 140–160°C is described as far too hot for perovskite modules.
* A finished module must meet IEC 61215, UL 2703 and other criteria to enable bankability.
* IEC 61215-1-6 is described as a perovskite standard being initiated under the IEC commission, with its status unknown.

📋 **Clip Abstract** Standard PV modules are laminated at 140–160°C with vacuum and pressure, a process described as far too hot for perovskites. The clip links junction-box and frame assembly, IEC 61215 and UL 2703 compliance, and IEC 61215-1-6—described as being initiated for perovskites—to bankability.

About the speaker:
* Speaker: David McDougall
* Company: HB Fuller
* Event: Perovskite Connect 2026 | Berlin
* Location: Estrel, Berlin

Save the date: Perovskite Connect 2027 | 20 and 21 OCT 2027 | Berlin
Co-located with the Future of Electronics RESHAPED conference and exhibition
Learn more: https://www.techblick.com/perovskiteconnect

Intestered in exhibiting: learn more here: https://www.techblick.com/perovskiteconnect

#PerovskiteModuleLamination, #GlassEncapsulantStack, #IEC61215, #UL2703, #PerovskitePV, #SolarModuleBankability

12:13 - 13:42

Can a perovskite module work with no encapsulant using insulated-glass assembly?

Can a perovskite module work with no encapsulant using insulated-glass assembly?

The approach can adapt from size to size, making small form factors instead of big sheets; cutting encapsulants to specific sizes is a pain. The final idea is no encapsulant whatsoever, stealing from insulated glass: two pieces of glass, maybe with argon or dry air in between, with cells floated between them.

Assembly would follow window manufacturing, floating the cells between the glass. The issue being worked on is light trapping: glass has a refractive index around 1.5 and air 1.0, which can create birefringence or bouncing back of photons. There are issues there that need to be addressed.

To keep photons from reflecting back, the team has been texturing the glass on the inside and texturing the cells, a light-trapping process so photons bounce around inside the panel and eventually find the solar cell. A Colorado State University group plans a 70-kilowatt floating solar system in Thailand to prove the concept, now assembling 70 kilowatts.

In this short video, you can learn:
* The no-encapsulant concept uses two glass panes, possibly with argon or dry air, and floats cells between them.
* Light trapping must address a glass refractive index of about 1.5 against air at 1.0, which can cause birefringence or photon bounce-back.
* Texturing the inside glass and the cells aims to keep photons bouncing until they reach the solar cell, with a 70-kilowatt Thailand floating solar demonstration planned by a Colorado State University group.

📋 **Clip Abstract** No-encapsulant insulated-glass assembly is being explored for solar panels, with cells floated between two glass panes and light trapping addressed by texturing glass and cells. A Colorado State University group plans a 70-kilowatt floating solar system in Thailand to prove the concept.

About the speaker:
* Speaker: David McDougall
* Company: HB Fuller
* Event: Perovskite Connect 2026 | Berlin
* Location: Estrel, Berlin

Save the date: Perovskite Connect 2027 | 20 and 21 OCT 2027 | Berlin
Co-located with the Future of Electronics RESHAPED conference and exhibition
Learn more: https://www.techblick.com/perovskiteconnect

Intestered in exhibiting: learn more here: https://www.techblick.com/perovskiteconnect

#NoEncapsulant, #InsulatedGlassAssembly, #LightTrappingTexture, #SeventyKilowattDemo, #PerovskiteSolar, #FloatingSolar

09:11 - 11:40

Can perovskite modules be encapsulated at room temperature using liquid-fill or roll-to-roll methods borrowed from display glass?

Can perovskite modules be encapsulated at room temperature using liquid-fill or roll-to-roll methods borrowed from display glass?

Interconnect solders are not polymers, but they typically need 170 °C to process properly, so conductive adhesives are positioned as an alternative. The discussion pivots to room-temperature encapsulation routes borrowed from other industries, including OLED experience adapted to perovskites. Two methods are highlighted as proven elsewhere and tested at small scale, both aimed at avoiding the thermal budget of conventional lamination.

The first route is a liquid-filled system: an inject port fills a double glass cavity with polyurethane. It is used in display glass for stadium signs and Times Square-type installations, and in automotive glass for speedometers and instrument clusters, where outdoor protection and optical performance matter. A couple of solar customers have already played with the concept. It needs no heat and little CapEx; the fill process is simple.

The second route is roll-to-roll and described as sort of room temperature. A hopper is filled with polyolefin encapsulant and heated, transferring material to a roll at whatever temperature is needed to melt it—variable by product. The encapsulant transfers onto glass and is nip-rolled together into a finished product. It does not require lamination and does not require a lot of excess tools.

In this short video, you can learn:
* Solder interconnects typically require 170 °C, making conductive adhesives an alternative worth considering for thermally sensitive perovskite modules.
* Liquid-filled polyurethane encapsulation borrowed from display and automotive glass needs no heat and little CapEx, and has been tried by a couple of solar customers.
* Roll-to-roll polyolefin encapsulation heats material only to its melt point, transfers it to glass and nip-rolls a finished product without lamination or excess tools.

📋 **Clip Abstract** Two room-temperature encapsulation routes are presented as alternatives to 170 °C solder processing and conventional lamination. A liquid-filled polyurethane system borrowed from display and automotive glass requires no heat and little CapEx, while a roll-to-roll polyolefin process transfers melted encapsulant to glass and nip-rolls a finished product without lamination.

About the speaker:
* Speaker: David McDougall
* Company: HB Fuller
* Event: Perovskite Connect 2026 | Berlin
* Location: Estrel, Berlin

Save the date: Perovskite Connect 2027 | 20 and 21 OCT 2027 | Berlin
Co-located with the Future of Electronics RESHAPED conference and exhibition
Learn more: https://www.techblick.com/perovskiteconnect

Intestered in exhibiting: learn more here: https://www.techblick.com/perovskiteconnect

#LiquidFillPolyurethane, #RollToRollPolyolefin, #RoomTemperatureEncapsulation, #ConductiveAdhesiveInterconnect, #PerovskiteModules, #SolarCellPackaging


About this talk

→ Materials for Perovskite Modules · David McDougall · Perovskite Connect 2026

More Snippets
CONTACT US

KGH Concepts GmbH

Mergenthalerallee 73-75, 65760, Eschborn

+49 17661704139

admin@techblick.com

TechBlick is owned and operated by KGH Concepts GmbH

Registration number HRB 121362

VAT number: DE 337022439

  • LinkedIn
  • YouTube

Sign up for our newsletter to receive updates on our latest speakers and events AND to receive analyst-written summaries of the key talks and happenings in our events.

Thanks for submitting!

© 2026 by KGH Concepts GmbH

bottom of page