Denis Pasero | Ilika: How small can a solid-state battery get, and what charge rate and cycle life does it deliver at microamp-hour scale?
05:08 - 07:26
Other snippets from this talk
Summary of the clip:
How small can a solid-state battery get, and what charge rate and cycle life does it deliver at microamp-hour scale?
The first commercial product measures 5.6 by 3.6 millimetres and slightly over one millimetre thick, with each layer at 150 microns and 100 microns targeted soon. Shrinking the footprint costs energy density, so there is still work to do. Beyond medtech, IoT designers putting sensors on hot machinery are a target: cells run to 100 °C today, and are known to work to 150 °C.
These are micro batteries: hundreds of microamp hours today, with a roadmap toward a couple of milliamp hours. Because the cells are thin films, the distance lithium must navigate is short, so they charge and recharge very fast. They are also safe — no liquid and no thermal runaway. First product: M300, 300 microamp hours.
Charge to 80% of capacity in 8 minutes. At 10C the cell delivers about 70% of its available capacity continuously — 3 milliamps out of a 300 microamp-hour battery — and 20C in pulse mode. After 1,000 cycles the curve stays really flat, which is the durability headline here.
In this short video, you can learn:
* A 5.6 by 3.6 millimetre cell just over a millimetre thick is the first commercial format, with layer thickness dropping from 150 to 100 microns.
* Microamp-hour cells reach roughly 70% of available capacity continuously at 10C, or 3 milliamps from a 300 microamp-hour battery, plus 20C in pulse.
* The M300 retains a flat capacity curve beyond 1,000 cycles while running liquid-free with no thermal runaway.
📋 **Clip Abstract** Ilika's micro batteries start at 5.6 by 3.6 millimetres and just over a millimetre thick, with 150-micron layers moving to 100 microns and an M300 product rated at 300 microamp hours. Thin-film construction shortens the lithium path, giving 80% charge in 8 minutes, about 70% capacity at 10C continuous, 20C pulses and flat performance after 1,000 cycles.
About the speaker:
* Speaker: Denis Pasero
* Company: Ilika
* Event: Solid-State Batteries: Innovations, Promising Start-ups, Future Roadmap
* Location: Online
Join TechBlick to learn about the state of the art in solid state batteries, Si anode, advanced cathodes, sodium batteries, and beyond
https://www.techblick.com/
#M300Microbattery, #ThinFilmCell, #10CDischarge, #1000CycleStability, #SolidStateBatteries, #IoTEnergyStorage
This is a highlight of the presentation:
Micro to Giga Scale: Different Materials, Processes and Challenges
More Highlights from the same talk.
10:44 - 12:46
Can a solid electrolyte's 85 °C tolerance let EV designers shrink cooling and BMS complexity?
Can a solid electrolyte's 85 °C tolerance let EV designers shrink cooling and BMS complexity?
At watt-hour pouch scale, the solid-state cells have demonstrated operation at 75 and 80 °C, with work now examining 85 °C. Because there is no liquid, there is no thermal runaway and the cells are not flammable. The claimed upside includes higher energy density and, in the first MVP product on the roadmap, lithium equivalence with potential to go higher.
Power and charge, critical for EV use, remain to be seen. Higher energy density could support higher power, but these are solid materials, so lithium-ion transit is intrinsically lower; formulation and other tricks must compensate. That trade-off separates temperature tolerance from rate capability and needs to be resolved at cell level before pack-level benefits are banked.
The benefits land at pack level: designers could reduce cooling-system complexity if the battery can operate at higher temperatures during a long straight or rapid charging. The cells need not run above ambient, but they can. Safety may also simplify the BMS and monitoring system because thermal runaway risk is removed, although the clip frames this as potential rather than demonstrated.
In this short video, you can learn:
* Cells have been demonstrated at 75 and 80 °C, with 85 °C under investigation.
* No liquid means no thermal runaway and nonflammability, while the MVP targets lithium equivalence.
* Solid electrolytes intrinsically lower lithium-ion transit, so power and charge require formulation work and remain to be seen.
📋 **Clip Abstract** Solid-state pouch cells demonstrated at 75–80 °C and being examined at 85 °C remove liquid-related thermal runaway and flammability, with an MVP targeting lithium equivalence and potential for higher energy density. The pack-level promise is simpler cooling and BMS, but solid electrolytes intrinsically slow lithium-ion transit, leaving power and charge to be seen and dependent on formulation.
About the speaker:
* Speaker: Denis Pasero
* Company: Ilika
* Event: Solid-State Batteries: Innovations, Promising Start-ups, Future Roadmap
* Location: Online
Join TechBlick to learn about the state of the art in solid state batteries, Si anode, advanced cathodes, sodium batteries, and beyond
https://www.techblick.com/
#SolidStateElectrolyte, #85COperation, #LithiumEquivalence, #PouchCellScale, #SolidStateBatteries, #EVBatteryDesign
17:17 - 19:35
Why use an oxide electrolyte over sulfide, and what does silicon's volume expansion cost cycle life?
Why use an oxide electrolyte over sulfide, and what does silicon's volume expansion cost cycle life?
The chemistry is fully solid state—no hybrid, no polymer—and uses an oxide solid electrolyte. The driver is potential safety: sulfides are avoided to target a chemistry safe in use, safe in manufacturing and safer in recycling. The electrolyte is already produced at ton level, with kiloton or megaton scale needed later, from an industry that exists now.
At gigawatt-hour scale, an external cost model confirmed price parity for the cells. That matters commercially. The material supply chain is already engaged, and the electrolyte is manufactured today at ton level; scaling to kiloton or megaton is the later requirement. The choice is therefore not just electrochemical: it is manufacturability and recycling safety.
The anode is silicon. Its advantage over lithium is no dendrite occurrence, but silicon expands and contracts—cell breathing—during charge and discharge, which can hurt operation and cycle life. At thin-film level this was solved; here the problem differs. Formulation tricks and additions make the anode a composite material to prevent volume expansion from becoming detrimental, particularly to cycle life.
In this short video, you can learn:
* Oxide electrolytes are selected over sulfides for safety in use, manufacturing and recycling.
* An external gigawatt-hour cost model confirmed cell price parity, supporting commercial viability.
* Silicon's charge-discharge breathing is mitigated through composite formulation and additives to protect cycle life.
📋 **Clip Abstract** A fully solid-state cell uses an oxide electrolyte instead of sulfides to improve safety in use, manufacturing and recycling, with the material already produced at ton level. Silicon anode volume expansion is addressed through formulation and composite-material additions, while an external gigawatt-hour cost model confirms price parity.
About the speaker:
* Speaker: Denis Pasero
* Company: Ilika
* Event: Solid-State Batteries: Innovations, Promising Start-ups, Future Roadmap
* Location: Online
Join TechBlick to learn about the state of the art in solid state batteries, Si anode, advanced cathodes, sodium batteries, and beyond
https://www.techblick.com/
#OxideSolidElectrolyte, #SiliconAnode, #VolumeExpansion, #GigawattHourCostParity, #SolidStateBatteries, #BatteryMaterials
About this talk
→ Micro to Giga Scale: Different Materials, Processes and Challenges · Denis Pasero · Battery Materials: Next-Gen & Beyond Lithium Ion 2022


