Edward Crossland | Oxford Photovoltaics: What predicted annual field loss do light-on perovskite R&D cells reach in the harshest climates?
11:08 - 12:00
Other snippets from this talk
Summary of the clip:
What predicted annual field loss do light-on perovskite R&D cells reach in the harshest climates?
Turning the light on introduces the primary degradation mode inside the core perovskite technology. Testing is run across several temperatures, with clear cell size and clear measurement. Lower temperatures are now being examined in the labs because they tend to show lower degradation rates. Metastability and efficiency measurements require particular care during these runs.
Those tests run for multiple hundreds of hours depending on temperature, producing a degradation rate. That rate feeds a deployment model: over a particular deployment lifetime in a particular climate, it predicts percent loss per year. The cells shown are R&D cells, about 10 square centimeters total, with a few square centimeters active.
In the harshest climates, the model predicts 2% loss per year; easier climates give much less. That 2% figure is described as a fundamental limit for these R&D cells. The result links lab light-and-heat degradation testing to predicted annual field loss rather than a single accelerated-test number.
In this short video, you can learn:
* Light exposure is the primary degradation mode inside the core perovskite technology, so the testing turns the light on across several temperatures.
* Multiple hundreds of hours of testing yield a degradation rate that is plugged into a deployment model for a given lifetime and climate.
* The harshest climates show 2% predicted loss per year, described as a fundamental limit, with much less loss in easier climates.
đź“‹ **Clip Abstract** Light-on testing is the primary degradation mode for core perovskite technology, run across several temperatures with clear cell size and measurement while watching metastability and efficiency. Multiple hundreds of hours produce a degradation rate that feeds a deployment model, predicting 2% loss per year in the harshest climates for R&D cells of about 10 square centimeters total and much less in easier climates.
About the speaker:
* Speaker: Edward Crossland
* Company: Oxford Photovoltaics
* Event: Perovskite Connect 2026 | Berlin
* Location: Estrel, Berlin
Save the date: Perovskite Connect 2027 | 20 and 21 OCT 2027 | Berlin
Co-located with the Future of Electronics RESHAPED conference and exhibition
Learn more: https://www.techblick.com/perovskiteconnect
Intestered in exhibiting: learn more here: https://www.techblick.com/perovskiteconnect
#PerovskiteDegradation, #LightSoakTesting, #DeploymentModeling, #AnnualFieldLoss, #PerovskiteTandem, #SolarCellStability
This is a highlight of the presentation:
The Era of Perovskite-on-Silicon: Bringing Tandem Solar to Market
21 and 22 OCT 2026
Estrel, Berlin
Organised By:
More Highlights from the same talk.
07:08 - 09:13
What module materials let a silicon tandem survive stratospheric UV while staying below 500 g/m²?
What module materials let a silicon tandem survive stratospheric UV while staying below 500 g/m²?
For HAPS—stratospheric autonomous planes, balloons or unmanned craft for communications and survey—the cell must be high-efficiency, tuned to AM0 spectra, different operating temperatures and mission profiles. Lightweighting matters for launch cost into LEO orbits above 100 km, or simply for staying airborne and giving the HAPS vehicle maximum route flexibility.
In a silicon-based tandem cell—thin film on wafer—the wafer is all the weight in the cell, and cell and module are roughly 50/50 in product weight. Modules are now below 500 grams per square meter, split 50% cells and 50% module materials, so development focuses on lightweight module materials.
Those lightweight module materials still need to be moisture-proof, temperature-cycling compatible for cold stratospheric nights, UV-protecting and efficient. Engineering trades moisture barrier or UV stability against weight and encapsulation properties. Material screening can be simple: check whether candidates turn yellow under UV light on a fixed-wing, heavier-than-air HAPS mock-up.
In this short video, you can learn:
* HAPS cells must be tuned for AM0 spectra, varying temperatures and mission profiles while remaining lightweight.
* The silicon wafer dominates tandem-cell weight, with cell and module each about half of product weight.
* Module materials below 500 g/m² must combine moisture protection, temperature cycling and UV stability, screened by UV yellowing.
📋 **Clip Abstract** Stratospheric HAPS platforms require high-efficiency cells tuned to AM0 spectra and lightweight enough for launch or sustained flight. In silicon-based tandems, the wafer dominates cell weight, so modules below 500 g/m² depend on lightweight materials that remain moisture-proof, temperature-cycling compatible and UV-stable, with UV yellowing as a simple screen.
About the speaker:
* Speaker: Edward Crossland
* Company: Oxford Photovoltaics
* Event: Perovskite Connect 2026 | Berlin
* Location: Estrel, Berlin
Save the date: Perovskite Connect 2027 | 20 and 21 OCT 2027 | Berlin
Co-located with the Future of Electronics RESHAPED conference and exhibition
Learn more: https://www.techblick.com/perovskiteconnect
Intestered in exhibiting: learn more here: https://www.techblick.com/perovskiteconnect
#SiliconTandem, #HAPSModules, #AM0Spectrum, #UVYellowing, #PerovskiteTandem, #StratosphericSolar
19:07 - 20:53
Why is degradation spread wider than efficiency spread, and how do EL/PL screens catch bad cells?
Why is degradation spread wider than efficiency spread, and how do EL/PL screens catch bad cells?
Production runs show standard deviation below half a percent in efficiency, but above half a percent in degradation rate. That mismatch means reliability spread is wider than efficiency spread. The line uses EL screening, and PL screening is also explored, to pull out cells affectionately called bad apples before one cell kills a whole module.
Five years of manufacturing work has focused on tightening distributions in key processes: the perovskite itself and the direct contacts. Above them, hermetic layers must have zero defects. Sputtered TCO-type layers protect the cell from the outer environment and influence high-temperature and illumination effects on degradation paths such as halide migration, chemical reaction and loss out of the film.
At module level, edge seal and lamination foil selection and lamination foil quality are additional failure routes. The message is that the whole stack must be right, not just the cell, to make it work in the full module. That is why screening and process control extend beyond efficiency into reliability.
In this short video, you can learn:
* Efficiency standard deviation is under half a percent in production runs, while degradation-rate standard deviation is above half a percent.
* EL and PL screening are used inline to identify bad cells before module assembly.
* Key process control targets the perovskite, direct contacts and zero-defect hermetic sputtered TCO layers.
đź“‹ **Clip Abstract** Production data show tighter efficiency distributions than degradation distributions, so inline EL and PL screening is used to remove bad cells before module assembly. Manufacturing control focuses on the perovskite, direct contacts and zero-defect hermetic layers, with module edge seal and lamination foil quality also critical.
About the speaker:
* Speaker: Edward Crossland
* Company: Oxford Photovoltaics
* Event: Perovskite Connect 2026 | Berlin
* Location: Estrel, Berlin
Save the date: Perovskite Connect 2027 | 20 and 21 OCT 2027 | Berlin
Co-located with the Future of Electronics RESHAPED conference and exhibition
Learn more: https://www.techblick.com/perovskiteconnect
Intestered in exhibiting: learn more here: https://www.techblick.com/perovskiteconnect
#ELScreening, #PLScreening, #DegradationRate, #HalideMigration, #PerovskiteSolar, #TandemPhotovoltaics
16:59 - 18:54
Does vacuum-based tandem production ever pay back its higher CapEx through line productivity?
Does vacuum-based tandem production ever pay back its higher CapEx through line productivity?
The CapEx outlay is higher for vacuum equipment, but the answer is scale: platforms with productivity high enough that the extra spend is gained back, an argument that already worked very well for silicon. Current production volumes are described as baby brothers of the big systems, based on 100-megawatt lines.
Around 2,000 wafers per hour is the current benchmark, with some systems running less. The high-volume concept keeps the same schematic process in the facility today but moves to much bigger, more productive platforms, where detailed models combine CapEx outlay, OpEx, factory line and overall output to derive piece price.
Low CapEx is worth chasing, yet provided the line operates long enough it gets lost in the eventual economics. The constraint comes first: hit the quality requirement, because a miss there lets end yield kill the economics the other way, so low-cost manufacturing cannot compromise on quality and yield of each individual process.
In this short video, you can learn:
* Higher vacuum CapEx is recovered through platform productivity at scale, as silicon already demonstrated.
* Current 100-megawatt-based tools run at roughly 2,000 wafers per hour, the baby brothers of the high-volume platforms being designed.
* Quality and yield of each process come before low-cost manufacturing, because end yield can cancel the CapEx advantage.
đź“‹ **Clip Abstract** Asked whether vacuum-based tandem production can compete on cost, the answer rests on scale: productivity at high-volume platforms must absorb the higher CapEx outlay, an approach that already worked for silicon. Current 100-megawatt systems near 2,000 wafers per hour are small siblings of the planned platforms, modelled line by line to reveal piece price.
About the speaker:
* Speaker: Edward Crossland
* Company: Oxford Photovoltaics
* Event: Perovskite Connect 2026 | Berlin
* Location: Estrel, Berlin
Save the date: Perovskite Connect 2027 | 20 and 21 OCT 2027 | Berlin
Co-located with the Future of Electronics RESHAPED conference and exhibition
Learn more: https://www.techblick.com/perovskiteconnect
Intestered in exhibiting: learn more here: https://www.techblick.com/perovskiteconnect
#PerovskiteOnSilicon, #VacuumDeposition, #WafersPerHour, #PiecePriceModelling, #TandemSolarCells, #PerovskitePV
About this talk
→ The Era of Perovskite-on-Silicon: Bringing Tandem Solar to Market · Edward Crossland · Perovskite Connect 2026
Other talks by Edward Crossland
- The world's first commercial tandem perovskite-silicon module · The Future of Electronics RESHAPED 2025
More highlights from Edward Crossland
- ▶ Why is chasing rock-bottom production costs a fatal trap for next-generation solar technologies? · Perovskite Connect 2025
- ▶ Why are monolithic two-terminal cells winning the perovskite scaling war over four-terminal module configurations? · Perovskite Connect 2025
- ▶ How does the chemical reaction between silver metallization and halide perovskites threaten solar module lifetime? · Perovskite Connect 2025


