top of page

Eleni Margariti

University of Strathclyde

* All members of the platform can watch the entire presentation.

 

Please register to become a member.

Eleni Margariti | University of Strathclyde: What positional accuracy and local transfer yield did a 76,600-device QVGA array achieve with continuous roll transfer?

08:38 - 09:58

Other snippets from this talk

Summary of the clip:

What positional accuracy and local transfer yield did a 76,600-device QVGA array achieve with continuous roll transfer?

The demonstration was a printed quarter video graphics array containing 76,600 devices in total. Using continuous roll transfer, the devices were picked up and printed onto a silicon substrate. The printed array was then assessed with the method described earlier. Positional-accuracy analysis across more than 75,000 devices reported 980 nm positional accuracy.

Transfer yield was mapped, showing lower yield localized in specific areas. Checking those areas against the actual donor chip showed the devices were still there. Conventional pickup methods could not remove them, so the loss originated in device fabrication rather than the transfer process. On that basis, the actual transfer printing process achieved over 99.9% local transfer yield.

The result separates array-level losses from the roll-transfer step itself. Because the missing devices remained on the donor and resisted conventional pickup, the lower-yield regions were attributed to fabrication, not to continuous roll transfer. The reported 99.9% local transfer yield therefore describes the printing process, while the 76,600-device QVGA demonstration links positional accuracy and mapped transfer yield in one printed array.

In this short video, you can learn:
* Continuous roll transfer placed a 76,600-device QVGA array onto a silicon substrate.
* Positional-accuracy analysis over more than 75,000 devices reported 980 nm.
* Mapped lower-yield regions were traced to donor devices left by fabrication, giving over 99.9% local transfer yield.

📋 **Clip Abstract** A 76,600-device printed QVGA array was transferred onto silicon using continuous roll transfer. Analysis across more than 75,000 devices reported 980 nm positional accuracy and over 99.9% local transfer yield, with lower-yield regions attributed to device fabrication rather than the transfer process.

About the speaker:
* Speaker: Eleni Margariti
* Company: University of Strathclyde
* Event: MicroLED Connect 2024
* Location: High Tech Campus, Eindhoven, Netherlands

Join the most event MicroLED, AR/VR display and Optical I/O Connect event of the year
Learn more https://www.microledconnect.com/

#ContinuousRollTransfer, #MicroLEDMassTransfer, #QVGAArray, #LocalTransferYield, #MicroLEDDisplays, #PrintedElectronics

This is a highlight of the presentation:

Advancing Micro-LED Manufacturing: Overcoming Mass Transfer Challenges and Cost Barriers with Continuous Roll-Transfer Printing.

MicroLED Connect 2024

​

25-26 September 2024

High Tech Campus, Eindhoven, Netherlands

Organised By:

Metal Grass and TechBlick

​

More Highlights from the same talk.

04:11 - 06:06

Why do Micro-LED mass-transfer methods stay costly, and how does continuous roll transfer printing avoid those cost drivers?

Why do Micro-LED mass-transfer methods stay costly, and how does continuous roll transfer printing avoid those cost drivers?

Several proposed mass-transfer techniques have demonstrated accuracy and yield, yet cost remains the main challenge. That cost comes from two parts: the need for costly equipment and the use of an external driven force to perform printing, whether laser-assisted, electrostatic or fluidic transfer. A viable method must also be compatible with existing manufacturing process flows to integrate seamlessly into production lines.

The proposed method is based on continuous roll transfer printing and allows thousands of devices to be printed in a single shot. A roller on a continuous motion path accelerates the transfer rate significantly. The mechanical parts are kept simple, so minimizing equipment requirements reduces the overall project significantly, while the approach remains compatible with existing process flows.

The method is highly scalable because there is no limitation as the roller keeps moving. By changing the contact area of the roller with the tip, there is no limitation on the actual number of devices that can be picked up. This continuous roll-transfer approach targets fast, accurate printing while avoiding external driven-force and costly-equipment requirements.

In this short video, you can learn:
* Existing mass-transfer methods achieve accuracy and yield but remain cost-limited by costly equipment and an external driven force.
* Continuous roll transfer printing uses a roller in continuous motion to print thousands of devices in a single shot and accelerate transfer rate.
* Keeping mechanical parts simple and changing roller-tip contact area makes the method scalable without a limit on picked-up devices.

📋 **Clip Abstract** Existing Micro-LED mass-transfer techniques can deliver accuracy and yield, but their need for costly equipment and an external driven force keeps cost high. Continuous roll transfer printing addresses these drivers by using a continuously moving roller, simple mechanical parts and a changing contact area to print thousands of devices in a single shot and scale without a pick-up limit.

About the speaker:
* Speaker: Eleni Margariti
* Company: University of Strathclyde
* Event: MicroLED Connect 2024
* Location: High Tech Campus, Eindhoven, Netherlands

Join the most event MicroLED, AR/VR display and Optical I/O Connect event of the year
Learn more https://www.microledconnect.com/

#ContinuousRollTransferPrinting, #MassTransferCostBarriers, #RollerContactArea, #SingleShotDevicePrinting, #MicroLEDDisplays, #PrintedElectronics

10:32 - 11:59

How small must Micro-LEDs get for TVs, wearables and head-up displays, and which alignment step comes next?

How small must Micro-LEDs get for TVs, wearables and head-up displays, and which alignment step comes next?

Efficient, low-cost mass transfer of Micro-LEDs lowers the cost barrier to entry into the Micro-LED market — an economic unlock rather than a purely technical one. Broader accessibility to a diverse range of products follows, giving companies that are pursuing display innovation a route into a rapidly evolving market, which the speaker frames as an opportunity to lead rather than merely participate.

Looking ahead, the research targets enhancement of the mass transfer technique itself, focused mainly on overlay alignment and accuracy. The printed devices shown were 30 by 30 micrometre squares; the team has since gone down to 20 micrometres and is targeting smaller Micro-LEDs still, because shrinking the die is also what unlocks new applications.

Die size maps directly onto product classes. Around 50 micrometres is described as enough for televisions or smartphones, while wearable devices and head-up displays demand smaller Micro-LEDs. That split turns shrinking from a pure scaling exercise into an application gate: the wearable and HUD segments only open once transfer and overlay alignment hold at dimensions below the television-class floor.

In this short video, you can learn:
* Low-cost, efficient mass transfer is presented as the route that lowers cost barriers to entering the Micro-LED market and widens accessibility to a diverse range of products.
* The next research step is enhancing the mass transfer technique, mainly in overlay alignment and accuracy.
* Demonstrated devices were 30 by 30 micrometre squares and have reached 20 micrometres, while about 50 micrometres suffices for televisions and smartphones and wearables and head-up displays need smaller dies.

📋 **Clip Abstract** Efficient, low-cost mass transfer of Micro-LEDs is framed as the way to cut cost barriers to market entry and broaden access to products. The next step targets overlay alignment and accuracy, with devices scaled from 30 by 30 micrometre squares down to 20 micrometres, since televisions and smartphones need around 50 micrometres while wearables and head-up displays require smaller LEDs.

About the speaker:
* Speaker: Eleni Margariti
* Company: University of Strathclyde
* Event: MicroLED Connect 2024
* Location: High Tech Campus, Eindhoven, Netherlands

Join the most event MicroLED, AR/VR display and Optical I/O Connect event of the year
Learn more https://www.microledconnect.com/

#MicroLEDMassTransfer, #OverlayAlignmentAccuracy, #20MicrometreSquares, #HeadsUpDisplayOptics, #MicroLEDDisplays, #DisplayManufacturing

More Snippets
CONTACT US

KGH Concepts GmbH

Mergenthalerallee 73-75, 65760, Eschborn

+49 17661704139

admin@techblick.com

TechBlick is owned and operated by KGH Concepts GmbH

Registration number HRB 121362

VAT number: DE 337022439

  • LinkedIn
  • YouTube

Sign up for our newsletter to receive updates on our latest speakers and events AND to receive analyst-written summaries of the key talks and happenings in our events.

Thanks for submitting!

© 2026 by KGH Concepts GmbH

bottom of page