Falcon Liu | PlayNitride: Why does 99.9% transfer yield still leave over 30,000 bad pixels in Full HD, and how can mass repair address them?
09:38 - 11:36
Other snippets from this talk
Summary of the clip:
Why does 99.9% transfer yield still leave over 30,000 bad pixels in Full HD, and how can mass repair address them?
The display industry requires zero defect, normally set higher than 99.99999% yield, which is almost impossible without a repair process. Defective microarray chips and imperfect mass transfer both cause yield loss: defective chips may reach 99.5% yield, while imperfect mass transfer may lose 0.1% of yield. In a Full HD display, this can leave more than 30,000 bad MLD chips, making one-by-one repair unlikely.
A smart repair technology is therefore needed. Selective mass addressable repair, named SmartTag, first turns on micro LEDs and determines the address of bad pixels. The mass repair system then picks up chips from the source wafer based on the bad-pixel address and places them onto the backplane. This process is similar to mass transfer, which is faster and low cost. By repeating this process, mass repair can be performed.
The described workflow uses a mass repair system rather than repairing bad chips individually. It turns on micro LEDs to locate bad pixels, picks chips from the source wafer based on bad-pixel address, and transfers them to the backplane. Repeating the cycle is presented as enabling mass repair while retaining the speed and low-cost character of mass transfer.
In this short video, you can learn:
* Zero-defect MicroLED displays require yields above 99.99999%, so repair is essential because defective microarray chips and imperfect mass transfer still cause loss.
* Full HD can contain more than 30,000 bad MLD chips when chip yield is 99.5% and mass transfer loses 0.1%.
* SmartTag uses selective mass addressable repair: it turns on micro LEDs to find bad-pixel addresses, then picks chips from the source wafer and transfers them to the backplane like mass transfer.
📋 **Clip Abstract** MicroLED displays need zero-defect yields above 99.99999%, yet defective microarray chips and imperfect mass transfer can still leave more than 30,000 bad MLD chips in Full HD. Selective mass addressable repair, SmartTag, locates bad pixels by turning on micro LEDs, then uses a mass repair system to pick chips from the source wafer by address and transfer them to the backplane, repeating a mass-transfer-like process.
About the speaker:
* Speaker: Falcon Liu
* Company: PlayNitride
* Event: Displays & Lighting 2021: Innovations & Market Trends
Join TechBlick to learn about the cutting edge in the display industry
https://www.techblick.com/
#SelectiveMassAddressableRepair, #SmartTag, #BadPixelAddress, #MassRepairSystem, #MicroLEDDisplays, #DisplayManufacturing
This is a highlight of the presentation:
Development of MicroLED Display and Future Opportunities
More Highlights from the same talk.
07:46 - 09:41
How does a four-step mass transfer process push micro LED assembly yield to 99.9%?
How does a four-step mass transfer process push micro LED assembly yield to 99.9%?
Mass transfer is named as the first challenge of making a micro LED display. Picking and placing chip by chip works, but it is too costly and needs a lot of time. To reach low-cost assembly, a mass transfer process was developed around four major steps, beginning with very precise arrangement of chips on the wafer.
Second, a pickup head picks up many of these chips. Third, the pickup head is moved to the target backplane, where the bonding position is precisely aligned. Fourth, the chips are bonded to the backplane and released from the pickup head. The process cycle is kept and repeated across the different colors to build the display.
The mass transfer yield can go as high as 99.9%. Against that number sits the display industry's requirement for zero defect, so the reported figure is not treated as the end point. The cycle is repeated for the RGB colors needed to make micro LED displays, which means the four steps carry the yield burden.
In this short video, you can learn:
* Chip-by-chip pick and place is rejected as too costly and too time-consuming for micro LED display assembly.
* The four steps are precise chip arrangement on the wafer, pickup-head pick-up, aligned placement on the target backplane, then bonding and release from the head.
* Reported mass transfer yield reaches as high as 99.9%, set against a display industry requirement of zero defect.
📋 **Clip Abstract** Mass transfer is the first challenge of micro LED display manufacturing, and chip-by-chip pick and place is too costly and slow. A four-step cycle of precise wafer arrangement, pickup-head pick-up, aligned bonding on the target backplane and release reaches yields as high as 99.9%, against an industry requirement of zero defect.
About the speaker:
* Speaker: Falcon Liu
* Company: PlayNitride
* Event: Displays & Lighting 2021: Innovations & Market Trends
Join TechBlick to learn about the cutting edge in the display industry
https://www.techblick.com/
#MassTransfer, #PickupHead, #BondingAlignment, #TransferYield, #MicroLEDDisplay, #DisplayManufacturing
07:53 - 08:30
Can 2.5-micron microLEDs solve the color-integration and PPI hurdles of next-generation AR display engines?
Can 2.5-micron microLEDs solve the color-integration and PPI hurdles of next-generation AR display engines?
MicroLED microdisplays designed for augmented reality applications demand unprecedented pixel densities alongside full-color integration. PlayNitride demonstrates this capability with a 0.49-inch high-performance microdisplay boasting an extraordinary 4,536 pixels per inch (PPI). This level of density is critical for eliminating the screen-door effect in near-eye optical systems like waveguides.
Achieving four-color integration within a single, ultra-compact microdisplay panel requires shrinking individual microLED chips to just 2.5 microns. At this microscopic scale, managing quantum efficiency, sidewall defects, and surface recombination velocity becomes a major semiconductor fabrication challenge. PlayNitride's successful prototyping signals a viable path forward for ultra-bright, compact light engines.
These microdisplays are actively being shipped as proof-of-concept samples to leading AR glasses companies. By delivering physical hardware with 2.5-micron emitters, the industry can finally test real-world optical efficiency, waveguide coupling loss, and system-level thermal dissipation before freezing finalized consumer-grade specifications.
In this short video, you can learn:
* The technical specifications of PlayNitride's 0.49-inch AR microdisplay, including its 4,536 PPI resolution.
* The material challenges of scaling microLED chips down to 2.5 microns for single-panel multi-color integration.
* How early proof-of-concept samples are shaping the commercial roadmap and specifications for tier-one AR glasses.
📋 **Clip Abstract** This clip highlights PlayNitride's ultra-high-density 0.49-inch microdisplay featuring a pixel density of 4,536 PPI achieved using 2.5-micron microLED chips. It outlines the strategic deployment of these panels as proof-of-concept samples for key augmented reality device manufacturers.
#SubThreeMicronLED, #ColorIntegration, #SidewallRecombination, #WaveguideCoupling, #ARLightEngines, #NearEyeOptics
17:57 - 19:22
Does the LED chip or TFT backplane limit transparent MicroLED pixel density, and what blocks windshield use?
Does the LED chip or TFT backplane limit transparent MicroLED pixel density, and what blocks windshield use?
The transparent-display limit is attributed not to the MicroLED chip but to the TFT backplane: its wiring lines and TFT size constrain the design. If very high pixel density like a Retina display is required, the display cannot be transparent. Choosing transparency therefore imposes a lower pixel-density trade-off, and the display cannot sit very close to the viewer or it will appear sandy or pixelized.
Windshield use is described as possible, but a windshield is not a flat screen or flat panel; it is flat glass with 2D bending, so substantial process development is still needed. That geometry adds manufacturing work beyond a conventional flat panel, and the answer remains conditional on solving those bending-related process requirements.
Regulation is a second constraint: requirements differ by country, and the example given is a total transparency requirement of 70%, which imposes restrictions on the display. Even with the TFT-backplane and pixel-density trade-offs understood, windshield adoption must satisfy these transparency rules. The conclusion is that windshield use is technically possible, but not without process development and regulatory compliance.
In this short video, you can learn:
* Transparent MicroLED pixel density is limited by TFT backplane wiring lines and TFT size, not by the LED chip.
* Retina-level pixel density and transparency are incompatible in this transparent-display approach, forcing a lower-density trade-off.
* Windshield use requires 2D-bent glass process development and compliance with country-specific rules such as a 70% total transparency requirement.
📋 **Clip Abstract** Transparent MicroLED displays are constrained less by the LED chip than by the TFT backplane, whose wiring lines and TFT size prevent Retina-like pixel density when transparency is required. Windshield use is technically possible but needs process work for 2D-bent glass and must meet country-specific transparency rules, including an example 70% total transparency requirement.
About the speaker:
* Speaker: Falcon Liu
* Company: PlayNitride
* Event: Displays & Lighting 2021: Innovations & Market Trends
Join TechBlick to learn about the cutting edge in the display industry
https://www.techblick.com/
#TFTBackplane, #TransparentMicroLED, #PixelDensityTradeoff, #TwoDimensionalBending, #MicroLEDDisplays, #DisplayBackplanes
About this talk
→ Development of MicroLED Display and Future Opportunities · Falcon Liu · Displays & Lighting: Innovations & Market Trends 2021
Other talks by Falcon Liu
- Development and Solutions of MicroLED Displays for Emerging Applications · Quantum Dots: Material Innovations and Commercial Applications 2022
More highlights from Falcon Liu
- ▶ Can 2.5-micron microLEDs solve the color-integration and PPI hurdles of next-generation AR display engines? · Mini- & Micro-LED Displays 2022: Markets, Manufacturing Innovations, Applications, Promising Start-ups
- ▶ Why is the microLED display industry shifting its mass transfer roadmap from stamp-based picks to laser-assisted deposition? · Mini- & Micro-LED Displays 2022: Markets, Manufacturing Innovations, Applications, Promising Start-ups
- ▶ Why is individual microLED testing commercially dead, and how does massive repair salvage manufacturing yields? · Mini- & Micro-LED Displays 2022: Markets, Manufacturing Innovations, Applications, Promising Start-ups


