Felippe Pavinatto | GE Aerospace: How do shrinking 3D-printed ceramic matrices enable high-density vias for embedded multichip modules?
05:01 - 07:17
Other snippets from this talk
Summary of the clip:
How do shrinking 3D-printed ceramic matrices enable high-density vias for embedded multichip modules?
The team used additive manufacturing to build 3D-printed ceramic matrices. The printer works with an ADDOP method, described as similar to cellular lithography: parts are built layer by layer by photo cross-linking a polymer resin containing ceramic particles. They first optimized process conditions toward producing small cavities and holes, then filled those holes with a conductor to turn them into through-plate conductors. The best plates were very thin, around half a millimeter, flat and with low roughness.
In terms of vias or holes, they fabricated holes with a 200-micron diameter and a 100-micron separation in those plates. That created really high-density via arrays outside and inside what they call pockets or cavities. The cavities were about one by one millimeter and 150 microns deep. These vias and cavities are the features filled with conductor for the embedded multichip module demonstrator.
Another important aspect characterized was position fidelity compared to design. There is high shrinkage when processing the ceramic slurries: the plates decrease in size by half, starting very big and shrinking during that step. For the final plate used in the embedded multichip module demonstrator, there are about 200 holes. They wanted to ensure that after that shrinking, those holes land in the right spots.
In this short video, you can learn:
* ADDOP builds ceramic parts layer by layer by photo cross-linking ceramic-particle-filled polymer resin.
* They achieved 200-micron-diameter holes at 100-micron separation for high-density via arrays.
* High shrinkage halves the ceramic plate size, making position fidelity critical for 200 holes in the demonstrator.
📋 **Clip Abstract** This clip shows how 3D-printed ceramic matrices are optimized for embedded conductors. It covers ADDOP photo cross-linking, half-millimeter plates, 200-micron vias at 100-micron separation, one-by-one-millimeter cavities, and the shrinkage-driven position-fidelity challenge for a 200-hole multichip module demonstrator.
About the speaker:
* Speaker: Felippe Pavinatto
* Company: GE Aerospace
* Event: The Future of Electronics RESHAPED 2025
* Location: Estrel, Berlin
🗓️ Save the date for the next Future of Electronic RESHAPED conference and exhibition
USA | Mountain View | 9-10 June 2027 : https://www.techblick.com/electronicsreshapedusa
Europe | Berlin | 20-21 October 2027: https://www.techblick.com/electronicsreshaped
#AdditiveCeramicMatrices, #Addop, #PhotoCrossLinking, #HighDensityViaArrays, #AdditiveElectronics, #EmbeddedPackaging
This is a highlight of the presentation:
Additive Electronics for Harsh Environment Applications in Aerospace
More Highlights from the same talk.
08:20 - 10:25
Can printed interconnects and coplanar waveguides replace wire bonds on RF dies without adding loss?
Can printed interconnects and coplanar waveguides replace wire bonds on RF dies without adding loss?
The work fabricated daisy-chain structures for electrical testing. Conductive adhesive was dispensed inside cavities, dice were picked and placed, a dielectric ramp was printed around the dice, and interconnects were printed on and off the die as wire-bond replacements. Electrical performance, thermo stability and stability to solder reflow were characterized because reflow was eventually wanted. The interconnects are fine features, 40 to 50 micron lines, very reproducible and eight microns thick, and they conform well to the step provided by the ramp onto the die.
A second test die had a microstrip RF line. Coplanar waveguide ports were developed to send signals onto the die and read from the other side. A whole lot of tests demonstrated that the printed CPW ports would not include high losses into the RF device, and that result was very positive. The team then proceeded to the actual COS die intended for the multichip module, a low-noise amplifier chip.
All developments were congregated into a unit cell: a COS die in a cavity with printed dielectric ramps and printed coplanar waveguide ports. The die called for capacitors, such as decoupling capacitors, for its operation. Those capacitors were not placed into pockets, so the step to print an interconnect over the capacitors was even higher. The interconnect over those capacitors therefore faced a higher step.
In this short video, you can learn:
* Printed interconnects for wire-bond replacement reached 40–50 micron line widths, eight micron thickness, and conformed well to the dielectric ramp step onto the die.
* Extensive testing indicated that printed coplanar waveguide ports did not introduce high losses into the RF device, a very positive outcome.
* The COS low-noise-amplifier unit cell combined a cavity die, printed dielectric ramps and printed coplanar waveguides, with decoupling capacitors not in pockets raising the interconnect step.
📋 **Clip Abstract** This clip covers printed daisy-chain structures, conductive adhesive dispensing, pick-and-place dice, printed dielectric ramps and printed interconnects as wire-bond replacements. It then moves to a microstrip RF test die and a COS low-noise amplifier, testing printed coplanar waveguide ports for RF loss and building a unit cell with printed ramps, waveguides and decoupling capacitors.
About the speaker:
* Speaker: Felippe Pavinatto
* Company: GE Aerospace
* Event: The Future of Electronics RESHAPED 2025
* Location: Estrel, Berlin
🗓️ Save the date for the next Future of Electronic RESHAPED conference and exhibition
USA | Mountain View | 9-10 June 2027 : https://www.techblick.com/electronicsreshapedusa
Europe | Berlin | 20-21 October 2027: https://www.techblick.com/electronicsreshaped
#ConductiveAdhesiveDispensing, #PrintedInterconnects, #CoplanarWaveguidePorts, #SolderReflowStability, #PrintedElectronics, #AdditiveElectronics
14:13 - 16:13
How does a passive printed gold frequency-selective surface measure 1000°C remotely without power or wires?
How does a passive printed gold frequency-selective surface measure 1000°C remotely without power or wires?
A first device attempt for a thousand C began with fundamental characterization of printed ink materials. Electrical and C two characterization methods and additional characterization protocols were applied to a number of inks on multiple substrates, including Illumina and ceramic matrix composites. The process then moved to aerosol jet and micro dispensing. The shown array is the aerosol jet printed version, what the work calls a frequency selective surface: an array of antenna elements printed on a high temperature compatible surface.
It is a totally passive device. There are no active electronics, no power sources; it is just printed gold on Illumina. When RF energy is shone onto it, it absorbs some and produces a resonant peak. Measuring what is reflected back to the interrogation system gives a null in frequency sweep curves. The null's position depends on temperature: as temperature rises, the substrate dielectric constant and the sensor array dimensions increase, shifting the peak to lower frequencies.
Tracking that peak position with temperature yields a very linear calibration line. For some temperature readings there are multiple points, meaning the measurement was done back and forth multiple times, and the signal is very reproducible. The clip also shows a couple of images of the characterization setup in the middle. This demonstrates the passive printed gold frequency selective surface as a temperature sensor read through an interrogation system, with no active electronics or power sources.
In this short video, you can learn:
* A frequency selective surface is an array of antenna elements printed on a high temperature compatible surface that collectively produces RF properties.
* The device is totally passive—printed gold on Illumina with no active electronics or power sources—and shows a resonant null when RF energy is reflected back to an interrogation system.
* Temperature increases raise the substrate dielectric constant and array dimensions, shifting the resonant peak to lower frequencies along a very linear, reproducible calibration.
📋 **Clip Abstract** A first attempt at a thousand C device began with electrical and C two characterization of printed inks on multiple substrates, including Illumina and ceramic matrix composites, followed by aerosol jet and micro dispensing. The resulting passive frequency selective surface—printed gold on Illumina—absorbs RF energy, reflects a resonant null whose position shifts to lower frequencies as temperature rises, and yields a very linear, reproducible calibration.
About the speaker:
* Speaker: Felippe Pavinatto
* Company: GE Aerospace
* Event: The Future of Electronics RESHAPED 2025
* Location: Estrel, Berlin
🗓️ Save the date for the next Future of Electronic RESHAPED conference and exhibition
USA | Mountain View | 9-10 June 2027 : https://www.techblick.com/electronicsreshapedusa
Europe | Berlin | 20-21 October 2027: https://www.techblick.com/electronicsreshaped
#FrequencySelectiveSurface, #AerosolJetPrinting, #PrintedGold, #CeramicMatrixComposites, #AdditiveElectronics, #PrintedElectronics
About this talk
→ Additive Electronics for Harsh Environment Applications in Aerospace · Felippe Pavinatto · The Future of Electronics RESHAPED 2025


