Fernando Zicarelli | ASADA MESH CO., LTD: How do you hit zero paste spread without changing the substrate or paste?
13:41 - 16:09
Other snippets from this talk
Summary of the clip:
How do you hit zero paste spread without changing the substrate or paste?
The measured spread varies by substrate: Iconics averaged about 2 microns total, roughly just over a micron per side, while DuPont B was less than 5 microns total, about 2 microns per side. The target is zero spread, and consistent minimal spread matters because circuitry uses different line widths. The motor sample showed a negative number—undersized and not optimized—while others ranged from 7 microns to 5s, with higher values in a DuPont series.
If you do not have time to search for another substrate or paste, artwork compensation is a technique to bring spread down. It should be considered when printing somewhere between 50+ microns design. Taking DuPont A and needing to adjust it down to zero, the artwork is made 5 microns smaller. It will still spread, but to the nominal number wanted.
The recommendation is to apply this approach broadly: rather than accepting whatever spread comes from an existing combination, compensate the artwork. Companies already do this, so zero spread becomes a practical target without changing substrate or paste, while accounting for the fact that pastes will spread and should land at the nominal dimension.
In this short video, you can learn:
* Iconics averaged about 2 microns total spread, while DuPont B was under 5 microns total.
* Artwork compensation can reduce spread by making the artwork smaller, such as 5 microns for DuPont A to approach zero.
* The technique was recommended for designs printed somewhere between 50+ microns, with the caveat that paste will still spread to the nominal dimension.
📋 **Clip Abstract** Spread measurements showed Iconics averaging about 2 microns total and DuPont B under 5 microns, while other substrates ranged to 7 microns and higher in a DuPont series; an unoptimized motor sample came undersized. Artwork compensation, such as making DuPont A artwork 5 microns smaller, was recommended to bring spread to zero, particularly when printing somewhere between 50+ microns design.
About the speaker:
* Speaker: Fernando Zicarelli
* Companies: ASADA MESH CO., LTD
* Event: Electronic Textiles, Wearable Sensors & Printed/Flexible Sensors 2021
* Location: Online
Join TechBlick - for the leading global event on wearable electronics
https://www.techblick.com/
#ArtworkCompensation, #PasteSpread, #DuPontA, #Iconics, #PrintedElectronics, #FlexibleSensors
This is a highlight of the presentation:
Understanding Surface Treatments for PET Substrates.
More Highlights from the same talk.
03:42 - 05:30
Which PET surface metric actually predicts the best printed resolution?
Which PET surface metric actually predicts the best printed resolution?
On A4-size PET, the short side and long side were measured, and Ra—average surface roughness—stayed fairly similar across the samples in the red window. Rz, however, was “all over” among different manufacturers. The notable observation was that when Rz values measured on the long and short sides were very close to each other, the best printed resolution occurred.
Contact angle was measured with water—the liquid available in the lab in Japan. A device tip drops water onto the substrate, and the angle is measured. Five measurements were taken for each substrate; maximum data showed the difference between the two and the average. The average is the number to look at, and a water-repellency number was assigned to each substrate.
Generally speaking, the substrates showing the lowest contact angle were the ones that printed with better resolution. That links the measured water contact angle to printed resolution on PET. The Rz closeness on long and short sides was the other observed resolution predictor, while Ra alone did not separate the manufacturers in the red window.
In this short video, you can learn:
* Ra stayed similar across samples while Rz varied widely by manufacturer.
* Best printed resolution coincided with close Rz values measured on the long and short sides.
* Lower average water contact angle generally corresponded to better printed resolution using five measurements per substrate.
📋 **Clip Abstract** A4-size PET substrates were compared using short-side and long-side roughness measurements, showing Ra similarity but manufacturer-to-manufacturer Rz spread. Best printed resolution aligned with close long/short-side Rz and, in general, with the lowest average water contact angle from five measurements per substrate.
About the speaker:
* Speaker: Fernando Zicarelli
* Companies: ASADA MESH CO., LTD
* Event: Electronic Textiles, Wearable Sensors & Printed/Flexible Sensors 2021
* Location: Online
Join TechBlick - for the leading global event on wearable electronics
https://www.techblick.com/
#PETSubstrates, #SurfaceRoughness, #ContactAngle, #PrintedResolution, #FlexibleElectronics, #PrintedSensors
21:22 - 22:11
What is screen printing's real resolution limit today—and where is production?
What is screen printing's real resolution limit today—and where is production?
The stated ultimate lab resolution for screen printing is around 15 microns, and the answer notes this has already been done in Japan. That figure is presented as a lab result, not the routine production capability. It sets the outer boundary of what has been demonstrated, separate from what can be printed comfortably and repeatedly.
Comfortable screen-printing resolution is placed somewhere between 20 and 30 microns. This is the range described as achievable right now without pushing to the demonstrated 15-micron lab limit. The contrast matters in practice: 15 microns is the laboratory benchmark, while 20 to 30 microns is the comfortable capability.
Industry adoption is slower. Customers are described as very slowly moving to narrower features, but generally speaking production today remains at 50 microns, or 30 to 50 microns and above. So the production discussion sits well above both the 20-to-30-micron comfortable range and the 15-micron lab result.
In this short video, you can learn:
* The ultimate lab resolution reported for screen printing is around 15 microns, already demonstrated in Japan.
* A comfortable current capability is given as 20 to 30 microns.
* Customers are moving only slowly to narrower features, with production generally at 50 microns or 30 to 50 microns and above.
📋 **Clip Abstract** The clip distinguishes screen printing’s demonstrated lab resolution from its comfortable and production capabilities. It reports around 15 microns in the lab, 20 to 30 microns comfortable, and customers generally at 50 microns or 30 to 50 microns and above.
About the speaker:
* Speaker: Fernando Zicarelli
* Companies: ASADA MESH CO., LTD
* Event: Electronic Textiles, Wearable Sensors & Printed/Flexible Sensors 2021
* Location: Online
Join TechBlick - for the leading global event on wearable electronics
https://www.techblick.com/
#ScreenPrintingResolution, #15MicronLabLimit, #20To30MicronCapability, #NarrowFeatureProduction, #PrintedElectronics, #FlexibleElectronics
About this talk
→ Understanding Surface Treatments for PET Substrates. · Fernando Zicarelli · Printed & Flexible Sensors & Actuators 2021
Other talks by Fernando Zicarelli
- Screen-printing Heating Devices: Limits and Challenges · TechBlick Innovations Festival | Free-To-Attend 2024
- Advanced screen printing technology update · CPES | Canadian Printable Electronics Symposium 2023
- The Future of Screen Printing for Printed Electronics Panel · The Future of Screen Printing for Printed Electronics 2023
- Pushing the performance limit of screen printing to sub-30um range · Printed, Hybrid, InMold, and 3D Electronics 2022


