top of page

Florian Mathies

Helmholtz-Zentrum Berlin

* All members of the platform can watch the entire presentation.

 

Please register to become a member.

Florian Mathies | Helmholtz-Zentrum Berlin: What stage-gate criteria separate a lab perovskite device from a pilot-line-ready material?

05:14 - 07:24

Other snippets from this talk

Summary of the clip:

What stage-gate criteria separate a lab perovskite device from a pilot-line-ready material?

The stage-gate process maps the steps from a small lab area to a big pilot line: what measurements are needed and how quality is measured. Driven by the Jülich group in the Solartab network, it gives a basis to develop further processes and projects within Solartab.

As the schematic shows, moving from a lab-based process where devices are worked on to different stages means scaling up: faster scale-up and larger modules. At the end, the materials actually used and usable in the process become fewer and fewer, while materials at the device level remain more research-focused.

Within the stage-gate process, materials reaching the later stages can be considered usable for a pilot line, whereas materials at the beginning, on a device level, are more research-focused. There may be many challenges to overcome to bring them to a higher stage level.

In this short video, you can learn:
* The stage-gate process defines what measurements and quality checks are needed between a small lab area and a big pilot line.
* The Jülich group drove this stage-gate process within the Solartab network to develop further processes and projects.
* Later-stage materials are fewer and more likely usable for a pilot line, while device-level materials remain research-focused with challenges to scale.

📋 **Clip Abstract** A stage-gate process connects small lab-area work to a big pilot line by defining steps, measurements and quality checks. Driven by the Jülich group in the Solartab network, it shows that scaling up yields faster, larger modules with fewer usable materials, while device-level materials remain research-focused and face challenges at higher stages.

About the speaker:
* Speaker: Florian Mathies
* Company: Helmholtz-Zentrum Berlin
* Event: Perovskite Connect 2026 | Berlin
* Location: Estrel, Berlin

Save the date: Perovskite Connect 2027 | 20 and 21 OCT 2027 | Berlin
Co-located with the Future of Electronics RESHAPED conference and exhibition
Learn more: https://www.techblick.com/perovskiteconnect

Intestered in exhibiting: learn more here: https://www.techblick.com/perovskiteconnect

#StageGateProcess, #PilotLineScaleUp, #SolartabNetwork, #MaterialQualityChecks, #PerovskiteSolarCells, #OpenInnovationActions

This is a highlight of the presentation:

Turning Perovskite Innovation into Impact: The Solar TAP Approach

​

​

21 and 22 OCT 2026

Estrel, Berlin

Organised By:

​

​

More Highlights from the same talk.

04:53 - 06:57

How does the Stage-Gate framework help scale perovskite solar cells from lab spin-coating to automated slot-die deposition?

How does the Stage-Gate framework help scale perovskite solar cells from lab spin-coating to automated slot-die deposition?

The Stage-Gate publication investigated single-junction perovskite solar cells and identified stages from small-area lab devices to mini modules, where PicoQuant showed early results, then larger modules maybe two square meters. The established framework covers perovskite and organic photovoltaics, the project's two main photovoltaic technologies.

This open-innovation action sits at low TRL, maybe three or four, even two, because spin coating is solely a lab process. Three involved centres aligned processes and working groups, establishing a common perovskite architecture and baseline as a standing operating procedure, so efficiencies can transfer between centres.

In future runs, slot-die coating is used, not only manual slot-die coating by a lab engineer or PhD student, but automated fabrication platforms, for example from Cypress, which also partners in SolarTEP. This future run uses slot die coating with automated fabrication platforms.

In this short video, you can learn:
* The Stage-Gate framework maps single-junction perovskite solar cells from small-area lab devices through PicoQuant mini modules to modules maybe two square meters.
* Three centres aligned processes and working groups to establish a common perovskite architecture and baseline as a standing operating procedure, enabling transferable efficiencies.
* Future runs use slot-die coating, moving from manual coating by a lab engineer or PhD student to automated fabrication platforms from Cypress, a SolarTEP partner.

📋 **Clip Abstract** A Stage-Gate framework for single-junction perovskite solar cells defines stages from small-area lab devices to mini modules, where PicoQuant showed early results, and larger modules maybe two square meters. The low-TRL open-innovation action aligned three centres on a common perovskite baseline, with future slot-die coating moving from manual operation to automated fabrication platforms such as Cypress.

About the speaker:
* Speaker: Florian Mathies
* Company: Helmholtz-Zentrum Berlin
* Event: nnovation Festival: Additive, Printed, Sustainable Electronics, MicroLEDs and AR/VR Displays, Perovskites | July 2026
* Location: Online Platform

Annual access to our onsite event(s), all online events and a library featuring over 1800 presentations (recordings + PDF) across all our onsite and onsite events and technology areas. Join us and over 2000 members from around the world now.
Explore and join now --> https://www.techblick.com/

#PerovskiteSolarCells, #SlotDieCoating, #AutomatedFabricationPlatforms, #TransferableEfficiencies, #OrganicPhotovoltaics, #EmergingPhotovoltaics

07:21 - 08:17

Can a single spin-coating SOP yield the same perovskite stack across five labs?

Can a single spin-coating SOP yield the same perovskite stack across five labs?

The team aligned processes by using one standard operating procedure for spin coating only, applied in five different labs. Over nearly one year, they measured different batches and aligned the processes. At the end, they found a stack and architecture that could be produced in all the labs with different people and different equipment at the different locations.

The outcome was a stack and architecture that was possible to produce in all the different labs, with different people doing it and different equipment in the different locations. The team was quite happy that they could show it was possible to transfer processes between labs. This work was part of aligning processes within the centers.

The example centered on aligning processes within centers, using one SOP for spin coating only. Validation ran for nearly one year, with different batches measured, and the stack and architecture were produced across five labs. The demonstration showed that process transfer between labs is possible even when people and equipment differ.

In this short video, you can learn:
* One spin-coating SOP was applied in five different labs.
* Nearly one year of measurements with different batches aligned the processes.
* A common stack and architecture were produced despite different people and equipment at different locations.

📋 **Clip Abstract** A single spin-coating standard operating procedure was applied in five different labs over nearly one year, with different batches measured to align processes. The teams found a stack and architecture that could be produced in all labs with different people and equipment, demonstrating process transfer between locations.

About the speaker:
* Speaker: Florian Mathies
* Company: Helmholtz-Zentrum Berlin
* Event: Perovskite Connect 2026 | Berlin
* Location: Estrel, Berlin

Save the date: Perovskite Connect 2027 | 20 and 21 OCT 2027 | Berlin
Co-located with the Future of Electronics RESHAPED conference and exhibition
Learn more: https://www.techblick.com/perovskiteconnect

Intestered in exhibiting: learn more here: https://www.techblick.com/perovskiteconnect

#SpinCoatingSOP, #PerovskiteStack, #ProcessAlignment, #CrossLabTransfer, #PerovskiteSolarCells, #Photovoltaics

10:06 - 11:29

Why does Europe still debate lead while China runs gigawatt perovskite single-junction and tandem factories?

Why does Europe still debate lead while China runs gigawatt perovskite single-junction and tandem factories?

The assessment is stark: China already has gigawatt factories producing perovskite solar cells, both single junctions and tandems. Europe remains in a debate over whether lead is acceptable, so the region is way behind on industrial adoption. Collaborators from China still show willingness to work with European groups, but that does not remove the competitive gap.

European research centres still bring expertise, especially on the analytics side, according to discussions with Chinese collaborators. That analytical capability is a lever for collaboration, not a claim of manufacturing parity. However, finding collaboration partners within Europe or Germany for new projects is becoming harder, which complicates the route from lab results to industrial relevance.

An audience question then asks whether machine learning and material prediction are relied on before fabricating devices. The question is posed but not answered here. The surrounding message remains the same: industrial scale in China, analytical strength in Europe, and a shrinking pool of European or German project partners.

In this short video, you can learn:
* China already operates gigawatt factories for perovskite solar cells, including single junctions and tandems, while Europe still debates lead.
* European groups are seen as bringing strong analytics expertise, and Chinese collaborators remain willing to work with them.
* Finding collaboration partners within Europe or Germany for new projects is getting harder, and the audience question on machine learning and material prediction was not answered in this excerpt.

📋 **Clip Abstract** China has gigawatt factories producing perovskite solar cells, both single junctions and tandems, while Europe remains behind and still debates whether lead is acceptable. European research groups retain analytics expertise and Chinese collaborators still work with them, but finding European or German project partners is becoming harder, and a question on machine learning and material prediction before device fabrication goes unanswered here.

About the speaker:
* Speaker: Florian Mathies
* Company: Helmholtz-Zentrum Berlin
* Event: nnovation Festival: Additive, Printed, Sustainable Electronics, MicroLEDs and AR/VR Displays, Perovskites | July 2026
* Location: Online Platform

Annual access to our onsite event(s), all online events and a library featuring over 1800 presentations (recordings + PDF) across all our onsite and onsite events and technology areas. Join us and over 2000 members from around the world now.
Explore and join now --> https://www.techblick.com/

#PerovskiteSolarCells, #SingleJunctionTandems, #GigawattFactories, #AnalyticsExpertise, #Photovoltaics, #SolarIndustry


About this talk

→ Turning Perovskite Innovation into Impact: The Solar TAP Approach · Florian Mathies · Perovskite Connect 2026


More highlights from Florian Mathies

More Snippets
CONTACT US

KGH Concepts GmbH

Mergenthalerallee 73-75, 65760, Eschborn

+49 17661704139

admin@techblick.com

TechBlick is owned and operated by KGH Concepts GmbH

Registration number HRB 121362

VAT number: DE 337022439

  • LinkedIn
  • YouTube

Sign up for our newsletter to receive updates on our latest speakers and events AND to receive analyst-written summaries of the key talks and happenings in our events.

Thanks for submitting!

© 2026 by KGH Concepts GmbH

bottom of page