top of page

Frederic SOULIER

Ceradrop MGI GROUP

* All members of the platform can watch the entire presentation.

 

Please register to become a member.

Frederic SOULIER | Ceradrop MGI GROUP: How fast can industrial roll-to-roll printed electronics run, and when does multi-material curing hurt throughput?

17:44 - 18:55

Other snippets from this talk

Summary of the clip:

How fast can industrial roll-to-roll printed electronics run, and when does multi-material curing hurt throughput?

Industrial-grade roll-to-roll equipment, coming from graphic arts, can run at up to 50 linear meters per minute in printed electronics. At that speed, masking and application of a resist, X-resist, are reported without any problem. This is the baseline for one material and one simple process, where the line works quite well.

Adding materials changes the constraint. When different materials must be cured, duplication becomes quite important, and the result can be decreasing productivity. This frames a throughput penalty for multi-material processing rather than a limit of the base roll-to-roll transport, which remains fast for a single simple process.

The practical split is process complexity: one material and one simple process can reach up to 50 meters per minute, while adding and curing different materials forces duplication. That duplication is where productivity can decrease, so multi-material throughput depends on how many repeated add-and-cure steps the line must accommodate.

In this short video, you can learn:
* Industrial-grade roll-to-roll lines reach up to 50 linear meters per minute for one material and one simple process.
* Masking and X-resist application are reported at that speed without any problem.
* Curing or adding different materials requires duplication, which can decrease productivity.

πŸ“‹ **Clip Abstract** Industrial-grade roll-to-roll equipment from graphic arts can reach 50 linear meters per minute for printed electronics when running one material and one simple process. Adding materials and curing steps requires duplication, and that duplication can decrease productivity for multi-material work.

About the speaker:
* Speaker: Frederic SOULIER
* Company: Ceradrop MGI GROUP
* Event: Electronics RESHAPED 2026 | Berlin
* Location: Estrel, Berlin

USA: The Future of Electronics RESHAPED | USA
πŸ“… Save the date: 9 and 10 June 2027
πŸ“ Mountain View, California (Silicon Valley)
πŸ“‹ Info: https://www.techblick.com/electronicsreshapedusa

Europe
The Future of Electronics RESHAPED | Berlin
πŸ“… Save the date: 20 and 21 October 2027
πŸ“ Berlin, Germany
πŸ“‹ Info: https://www.techblick.com/electronicsreshaped

#RollToRollEquipment, #XResistMasking, #MultiMaterialCuring, #ProductivityDrop, #PrintedElectronics, #DigitalAdditiveManufacturing

This is a highlight of the presentation:

Scaling Digital Additive Processes in Modern Electronics Manufacturing

​

21 and 22 OCT 2026

Estrel, Berlin

Organised By:

TechBlick

​

More Highlights from the same talk.

06:28 - 08:51

How much power, ink and time can digital additive solder mask save in PCB manufacturing?

How much power, ink and time can digital additive solder mask save in PCB manufacturing?

The digital additive solder-mask process uses inkjet to apply solder-mask or solder-resist inks directly onto FR4 and the substrate. MGI acquired Altix to develop, market and sell equipment that replaces several traditional PCB workflow tools with one inkjet system. The first unit was sold last month, with leads in the US and Asia.

The equipment combines electronic-business user experience, including motion, HMI and UX, with inkjet expertise from MGI and Ceradrop. Its direct benefit is a digital additive solder mask that can match customer requirements while addressing market trends and needs. The first systems are sold and the company is pushing other leads across continents.

Reported results for this use case are minus 70% power consumption, minus 50% ink consumption and minus 50% time use. The process also means fewer equipment units and fewer operators. It replaces multiple traditional PCB steps with a single inkjet application of solder resist directly on FR4.

In this short video, you can learn:
* The digital additive process applies solder-mask ink directly to FR4 or substrate via inkjet.
* The first equipment was sold last month, with further leads in the US and Asia.
* The reported use-case savings are 70% power, 50% ink and 50% time, with fewer equipment units and operators.

πŸ“‹ **Clip Abstract** This clip explains a digital additive solder-mask process using inkjet to deposit solder-resist inks directly on FR4 and substrates, consolidating several traditional PCB workflow tools into one system. It reports a first sale last month, leads in the US and Asia, and use-case savings of 70% power, 50% ink and 50% time with fewer equipment units and operators.

About the speaker:
* Speaker: Frederic SOULIER
* Company: Ceradrop MGI GROUP
* Event: Electronics RESHAPED 2026 | Berlin
* Location: Estrel, Berlin

USA: The Future of Electronics RESHAPED | USA
πŸ“… Save the date: 9 and 10 June 2027
πŸ“ Mountain View, California (Silicon Valley)
πŸ“‹ Info: https://www.techblick.com/electronicsreshapedusa

Europe
The Future of Electronics RESHAPED | Berlin
πŸ“… Save the date: 20 and 21 October 2027
πŸ“ Berlin, Germany
πŸ“‹ Info: https://www.techblick.com/electronicsreshaped

#SolderMaskInkjet, #DigitalAdditiveSolderMask, #PCBWorkflowConsolidation, #PowerInkTimeSavings, #PrintedElectronics, #AdditiveElectronics

16:13 - 17:08

Can digital additive equipment address a single component and still reach tens of thousands?

Can digital additive equipment address a single component and still reach tens of thousands?

The answer is application- and industry-dependent, not a single fixed run size. For prototyping, the smallest run can be only one component. The capability to address only one, plus all the variations of that one, is presented as a key advantage of digital additive processing.

In production, run sizes move to hundreds and thousands. Very often they are several tens of thousands, described as an average seen in the market. That range sits alongside the small-run prototyping case, so the same digital additive approach must span single parts and higher-volume production.

The practical question is therefore not one run size but the range an application requires. Prototyping may need one component and its variations; production may need hundreds, thousands or tens of thousands. Digital additive equipment is positioned to cover that spread rather than a single narrow production volume.

In this short video, you can learn:
* Prototyping can require a run of only one component, plus variations of that component.
* Production runs can be hundreds or thousands of components.
* Several tens of thousands per run is described as an average seen in the market.

πŸ“‹ **Clip Abstract** Run size for digital additive equipment depends on the target application and industry. The discussed range spans single-component prototyping runs through hundreds, thousands and often several tens of thousands in production.

About the speaker:
* Speaker: Frederic SOULIER
* Company: Ceradrop MGI GROUP
* Event: Electronics RESHAPED 2026 | Berlin
* Location: Estrel, Berlin

USA: The Future of Electronics RESHAPED | USA
πŸ“… Save the date: 9 and 10 June 2027
πŸ“ Mountain View, California (Silicon Valley)
πŸ“‹ Info: https://www.techblick.com/electronicsreshapedusa

Europe
The Future of Electronics RESHAPED | Berlin
πŸ“… Save the date: 20 and 21 October 2027
πŸ“ Berlin, Germany
πŸ“‹ Info: https://www.techblick.com/electronicsreshaped

#SinglePartPrototyping, #ProductionRunRange, #TensOfThousandsProduction, #DigitalAdditiveRuns, #PrintedElectronics, #AdditiveElectronics

11:33 - 12:47

Can inkjet-printed 3D microstructured battery electrodes charge five times faster?

Can inkjet-printed 3D microstructured battery electrodes charge five times faster?

Using inkjet equipment, Dyname printed 3D microstructured electrodes for batteries. Those electrodes enable charging and loading/unloading at very high power. The stated result is up to five times faster charging than flat electrodes, with the goal being high-energy batteries and 100% additive-printed electrodes.

The electrodes are described as compatible with all battery chemistries, including lithium ion and lithium polymer. The main goals combine 3D microstructured electrodes, high energy batteries, five times faster charging, and 100% additive printing for the electrodes. This is the concrete battery example used to show what digital additive processing can deliver.

The stated reason for moving to a digital additive process was the capability to address many customers and to address small... The battery example directly connects inkjet printing, 3D microstructure, high-power charging and additive electrode manufacturing.

In this short video, you can learn:
* Inkjet printing produced 3D microstructured battery electrodes with up to five times faster charging than flat electrodes.
* The electrodes were described as 100% additive printed and compatible with all battery chemistries, including lithium ion and lithium polymer.
* The stated rationale for digital additive processing was the ability to address many customers and to address small...

πŸ“‹ **Clip Abstract** Inkjet printing was used to create 3D microstructured battery electrodes that enable very high-power charging and loading/unloading. The claimed result is up to five times faster charging than flat electrodes, with 100% additive-printed electrodes compatible with lithium-ion and lithium-polymer chemistries.

About the speaker:
* Speaker: Frederic SOULIER
* Company: Ceradrop MGI GROUP
* Event: Electronics RESHAPED 2026 | Berlin
* Location: Estrel, Berlin

USA: The Future of Electronics RESHAPED | USA
πŸ“… Save the date: 9 and 10 June 2027
πŸ“ Mountain View, California (Silicon Valley)
πŸ“‹ Info: https://www.techblick.com/electronicsreshapedusa

Europe
The Future of Electronics RESHAPED | Berlin
πŸ“… Save the date: 20 and 21 October 2027
πŸ“ Berlin, Germany
πŸ“‹ Info: https://www.techblick.com/electronicsreshaped

#3DMicrostructuredElectrodes, #InkjetPrintedElectrodes, #AdditiveBatteryElectrodes, #FiveTimesFasterCharging, #PrintedElectronics, #BatteryManufacturing


About this talk

β†’ Scaling Digital Additive Processes in Modern Electronics Manufacturing Β· Frederic SOULIER Β· The Future of Electronics RESHAPED 2026 Berlin


Other talks by Frederic SOULIER

More Snippets
CONTACT US

KGH Concepts GmbH

Mergenthalerallee 73-75, 65760, Eschborn

+49 17661704139

admin@techblick.com

TechBlick is owned and operated by KGH Concepts GmbH

Registration number HRB 121362

VAT number: DE 337022439

  • LinkedIn
  • YouTube

Sign up for our newsletter to receive updates on our latest speakers and events AND to receive analyst-written summaries of the key talks and happenings in our events.

Thanks for submitting!

© 2026 by KGH Concepts GmbH

bottom of page