top of page

Hani Kanaan

Dracula Technologies

* All members of the platform can watch the entire presentation.

 

Please register to become a member.

Hani Kanaan | Dracula Technologies: Why does a 2 V OPV module need four cells in series to reach 90% PMIC efficiency?

10:19 - 12:49

Other snippets from this talk

Summary of the clip:

Why does a 2 V OPV module need four cells in series to reach 90% PMIC efficiency?

For an autonomous device, the storage element is normally a battery, and an energy-harvesting source can extend its lifetime or eliminate it. With OPV, light varies—room sensor light off, light on—so current changes over time. A power management IC must track this variation and put it into the storage element.

First understand how much the IoT device consumes per day or week. For day-only operation, no storage is needed: where light exists, the panel delivers energy and the device wakes; without light, it enters sleep mode. For 24/7 operation, a small battery covers one week or one month, not several years.

For battery charging, the PMIC must track light-driven current variation, step up voltage to battery charging voltage and have highest conversion rate. On a commercial PMIC curve, 2 V input gives more than 90% conversion. The OPV panel must match end-user shape but deliver 2 V: four cells in series because each cell delivers 0.5 V; cell surface sets current proportional to light intensity.

In this short video, you can learn:
* A power management IC tracks OPV current variation from changing light and steps up voltage to the battery charging voltage.
* For day-only operation, no storage is needed; for 24/7 operation, a small battery can cover one week or one month.
* A commercial PMIC reaches more than 90% conversion at 2 V input, so the OPV panel uses four 0.5 V cells in series and cell area sets current proportional to light intensity.

📋 **Clip Abstract** OPV energy harvesting for autonomous IoT must handle varying light and current by using a power management IC to charge a storage element. After defining consumption and battery charging voltage, the design targets a commercial PMIC with >90% conversion at 2 V, requiring four 0.5 V cells in series and cell surface area proportional to light intensity.

About the speaker:
* Speaker: Hani Kanaan
* Company: Dracula Technologies
* Event: nnovation Festival: Additive, Printed, Sustainable Electronics, MicroLEDs and AR/VR Displays, Perovskites | July 2026
* Location: Online Platform

Annual access to our onsite event(s), all online events and a library featuring over 1800 presentations (recordings + PDF) across all our onsite and onsite events and technology areas. Join us and over 2000 members from around the world now.
Explore and join now --> https://www.techblick.com/

#OPVEnergyHarvesting, #PowerManagementIC, #BatteryChargingVoltage, #PMICConversionEfficiency, #OrganicPhotovoltaics, #IoTEnergyHarvesting

This is a highlight of the presentation:

​

Innovation Festival: Additive, Printed, Sustainable Electronics

Innovation Festival: MicroLEDs and AR/VR Displays

46213

Online Platform

Organised By:

TechBlick

TechBlick and MicroLED Industry Association

More Highlights from the same talk.

05:32 - 07:19

What does a 42 cm² OPV module deliver at 1,000 lux, and how much does the new non-fullerene acceptor add?

What does a 42 cm² OPV module deliver at 1,000 lux, and how much does the new non-fullerene acceptor add?

The commercialized module measures around 42 cm² and delivers more than 1.1 milliwatt at 1,000 lux. It is very sensitive to low light: energy generation starts at 50 lux for IoT devices, and the cells can even collect energy from five lux. That low-light sensitivity defines the indoor harvesting window.

In R&D, a new material — the non-fullerene acceptor donor — already demonstrates performance improvement of more than 30 percent, with transfer to mass production planned within 2024. That gain matters because the same module footprint can yield more harvested power without changing the device architecture or the low-light operating window.

OPV is a multilayer stack: flexible PET substrate, transparent conductive oxide, then etching of that oxide to define the cell or module shape. Organic material printing follows, then the electrode, then encapsulation. Characterisation selects defects, which are removed, and the rest goes to market. Manufacturing sits in a 2,000 square metre Valence factory with clean rooms and a first automated sheet-to-sheet line.

In this short video, you can learn:
* The commercial module delivers more than 1.1 milliwatt at 1,000 lux from a 42 cm² area.
* Harvesting starts at 50 lux for IoT devices, with energy collected down to five lux.
* A non-fullerene acceptor donor in R&D improves performance by more than 30 percent, targeted for mass production within 2024.

📋 **Clip Abstract** The commercialised OPV module covers around 42 cm² and yields over 1.1 milliwatt at 1,000 lux, with low-light harvesting from 50 lux down to five lux for IoT devices. A non-fullerene acceptor donor under development shows more than 30 percent performance improvement, while production follows an etch-print-encapsulate flow on flexible PET inside a 2,000 square metre Valence factory.

About the speaker:
* Speaker: Hani Kanaan
* Company: Dracula Technologies
* Event: nnovation Festival: Additive, Printed, Sustainable Electronics, MicroLEDs and AR/VR Displays, Perovskites | July 2026
* Location: Online Platform

Annual access to our onsite event(s), all online events and a library featuring over 1800 presentations (recordings + PDF) across all our onsite and onsite events and technology areas. Join us and over 2000 members from around the world now.
Explore and join now --> https://www.techblick.com/

#NonFullereneAcceptor, #TransparentConductiveOxide, #LowLightEnergyHarvesting, #SheetToSheetProduction, #IndoorPhotovoltaics, #PrintedElectronics


Other talks by Hani Kanaan


More highlights from Hani Kanaan

More Snippets
CONTACT US

KGH Concepts GmbH

Mergenthalerallee 73-75, 65760, Eschborn

+49 17661704139

admin@techblick.com

TechBlick is owned and operated by KGH Concepts GmbH

Registration number HRB 121362

VAT number: DE 337022439

  • LinkedIn
  • YouTube

Sign up for our newsletter to receive updates on our latest speakers and events AND to receive analyst-written summaries of the key talks and happenings in our events.

Thanks for submitting!

© 2026 by KGH Concepts GmbH

bottom of page