Huy Nguyen | Voltera: Does material compatibility decide if printed circuits survive three-dimensional thermoforming with electrical performance intact?
02:45 - 03:53
Other snippets from this talk
Summary of the clip:
Does material compatibility decide if printed circuits survive three-dimensional thermoforming with electrical performance intact?
In-mold electronics growth is driven by demand for lighter, thinner, and more integrated electronic devices. The automotive industry is a clear example, with manufacturers moving toward seamless interiors that integrate touch controls, lighting, and smart surfaces. By incorporating electronics directly into molded parts, IME can potentially reduce component count, simplify assembly, and give designers more freedom.
The central challenge is material compatibility. Electronics are printed onto a flat film and then formed into a three-dimensional shape, so the materials must withstand stretching and deformation without losing electrical performance. That is where NOVA becomes particularly valuable: it lets research experiment with different circuit designs before moving into the more expensive forming and thermoforming process.
For designers, the payoff is fewer components, simpler assembly, and freedom to create seamless interiors with integrated controls and lighting. The barrier is preserving electrical performance through stretching and deformation. NOVA supports the research stage by letting teams test different circuit designs before committing to expensive forming and thermoforming, which is the practical system focus introduced for the session.
In this short video, you can learn:
* IME is growing because devices are becoming lighter, thinner and more integrated, especially in automotive seamless interiors with touch controls, lighting and smart surfaces.
* Material compatibility is the key challenge because printed electronics on a flat film must survive three-dimensional stretching and deformation without losing electrical performance.
* NOVA lets researchers experiment with different circuit designs before the more expensive forming and thermoforming process.
📋 **Clip Abstract** The clip explains that in-mold electronics growth is driven by demand for lighter, thinner and more integrated devices, especially automotive seamless interiors with touch controls, lighting and smart surfaces. It identifies material compatibility—printed circuits on flat films must withstand three-dimensional stretching and deformation without losing electrical performance—and positions NOVA for circuit-design experimentation before expensive forming and thermoforming.
About the speaker:
* Speaker: Huy Nguyen
* Company: Voltera
* Event: Sustainable Electronics RESHAPED 2026 | Berlin
* Location: Estrel, Berlin
Sustainable Electronics RESHAPED | Berlin
📅 Save the date: 20 and 21 October 2027
📍 Berlin, Germany
📋 Info: https://www.techblick.com/sustainableelectronicsreshaped
#InMoldElectronics, #Thermoforming, #MaterialCompatibility, #NOVA, #AdditiveElectronics, #HumanMachineInterfaces
This is a highlight of the presentation:
Thermoformable Printed Circuits for In-Mold Human-Machine Interfaces
More Highlights from the same talk.
10:07 - 12:00
Can one dispenser handle 1,000 to 1,000,000 centipoise inks on TPU, PET, polyimide and textiles?
Can one dispenser handle 1,000 to 1,000,000 centipoise inks on TPU, PET, polyimide and textiles?
For in-mold electronics, material and substrate selection is framed as essential because printed circuits and electronics must survive thermoforming. NOVA supports conductive inks, adhesives, dielectrics and encapsulants, and can print on flexible films including TPU, PET, polyimide and textiles. The talk stresses that materials do not behave identically: some offer excellent connectivity but struggle with stretching, while others are more flexible with different electrical properties.
NOVA is described as supporting a viscosity range from approximately 1,000 centipoise to one million centipoise, from relatively fluid inks to thicker pastes. The demonstrated applications used different material-substrate combinations: gold electrodes on TPU for an ECG electrode, battery materials on PET for flexible batteries, heater inks on cotton fabric for wearable devices, and nanocopper on paper for RFID. A dispensed icing-sugar gingerbread example is also cited.
Each application is presented as a different combination of material and substrate, highlighting the dispenser's flexibility to develop printed electronics beyond traditional rigid circuit boards. The clip then transitions from these capability examples to applying the same approach specifically in mold electronics. This sets up IME as the target use case after electrode, battery, heater and RFID demonstrations on flexible or textile substrates.
In this short video, you can learn:
* NOVA supports conductive inks, adhesives, dielectrics and encapsulants on TPU, PET, polyimide and textiles for thermoformed printed circuits.
* Its stated viscosity window spans approximately 1,000 to 1,000,000 centipoise, covering fluid inks through thicker pastes.
* Demonstrations include gold electrodes on TPU for ECG, battery materials on PET, heater inks on cotton and nanocopper on paper for RFID.
📋 **Clip Abstract** Material and substrate selection for in-mold electronics must survive thermoforming, and NOVA is presented as supporting conductive inks, adhesives, dielectrics, encapsulants, and flexible films including TPU, PET, polyimide and textiles. The clip cites a viscosity range from approximately 1,000 to 1,000,000 centipoise and applications such as gold ECG electrodes on TPU, flexible batteries on PET, wearable heaters on cotton and nanocopper RFID on paper.
About the speaker:
* Speaker: Huy Nguyen
* Company: Voltera
* Event: Sustainable Electronics RESHAPED 2026 | Berlin
* Location: Estrel, Berlin
Sustainable Electronics RESHAPED | Berlin
📅 Save the date: 20 and 21 October 2027
📍 Berlin, Germany
📋 Info: https://www.techblick.com/sustainableelectronicsreshaped
#ConductiveInkDispensing, #FlexibleFilmSubstrates, #NanocopperRFID, #ECGElectrodesOnTPU, #PrintedElectronics, #InMoldElectronics
14:12 - 16:15
Can a printed capacitive touch sensor survive thermoforming and still drive an Arduino interface?
Can a printed capacitive touch sensor survive thermoforming and still drive an Arduino interface?
The circuit was printed using two different functional materials, eliminating traditional screen printing tooling. A thermoforming buck was 3D printed to give the plastic film its final shape; the design accounted for how much the substrate would stretch and included slight wall angles so the finished part could be removed more easily. The ABS substrate was then heated and formed into a three-dimensional shape.
Thermoforming was the scariest part: conductive traces originally printed on a flat surface now faced heat and stretching that could crack or damage them. After forming, electrical continuity was checked to confirm the circuit was still functioning. An Arduino interface circuit and flexible ribbon cables were printed in-house on NOVA, and Kemet's conductive adhesive manually bonded connector pins to the printed traces, giving electrical connection and mechanical stability without traditional soldering.
After printing the conductive and dielectric layers, thermoforming the ABS substrate and connecting everything to the Arduino interface, the team demonstrated a working capacitive touch sensor with both a linear slider and a circular touch control. Interacting with either control produces an impulse that the Arduino detects and uses to activate LEDs, delivering immediate visual feedback. The result is a complete in-mold electronics prototype.
In this short video, you can learn:
* The thermoforming buck was 3D printed and designed with stretch allowance and slight wall angles so the formed ABS part releases easily.
* Conductive traces printed on a flat surface survived heating and stretching, confirmed by an electrical continuity check after thermoforming.
* Kemet conductive adhesive replaced soldering for connector-pin bonding, and the printed Arduino interface turned slider and circular touch inputs into LED feedback.
📋 **Clip Abstract** A capacitive touch circuit printed from two functional materials on flat ABS was thermoformed over a 3D-printed buck into a three-dimensional shape without cracking the conductive traces. Printed flexible ribbon cables and an Arduino interface, bonded with conductive adhesive instead of solder, let a linear slider and circular touch control switch LEDs.
About the speaker:
* Speaker: Huy Nguyen
* Company: Voltera
* Event: Sustainable Electronics RESHAPED 2026 | Berlin
* Location: Estrel, Berlin
Sustainable Electronics RESHAPED | Berlin
📅 Save the date: 20 and 21 October 2027
📍 Berlin, Germany
📋 Info: https://www.techblick.com/sustainableelectronicsreshaped
#ThermoformableCircuits, #PrintedCapacitiveTouch, #ConductiveAdhesiveBonding, #InMoldElectronics, #AdditiveElectronics, #SustainableElectronics
12:43 - 14:12
Can a multilayer capacitive touch sensor be printed in just over an hour without screen-printing tooling?
Can a multilayer capacitive touch sensor be printed in just over an hour without screen-printing tooling?
The workflow started by printing conductive traces and the touch sensor itself onto a flat ABS substrate using Kemet's conductive and dielectric inks. A thermoforming buck was then 3D-printed as the tool that would give the plastic its final shape. The printed ABS was heated and thermoformed into a three-dimensional form, and an Arduino interface circuit was printed to connect the sensor and test functionality.
The circuit design combined conductive traces, touch electrodes and connection pads. Two separate Kemet materials were used: AG-550EI silver ink formed the conductive layer directly on the ABS substrate in approximately 33 minutes, followed by a D260EI dielectric layer that provided insulation and helped reinforce the circuit in approximately 40 minutes.
In just over an hour of printing time, a multilayer capacitive touch circuit was created from two different functional materials without traditional screen-printing tooling. Validating the design in-house covers both material testing and full design validation, letting researchers iterate on in-mold electronic interfaces — printing, forming and then testing the connected sensor rather than outsourcing tooling.
In this short video, you can learn:
* Silver ink AG-550EI printed the conductive layer on ABS in roughly 33 minutes, with D260EI dielectric adding insulation in roughly 40 minutes.
* The full multilayer capacitive touch circuit was printed in just over an hour without traditional screen-printing tooling.
* A 3D-printed thermoforming buck formed the flat printed ABS into its final three-dimensional shape before the Arduino interface circuit was printed to test the sensor.
📋 **Clip Abstract** A multilayer capacitive touch sensor was printed on flat ABS with two Kemet functional inks, then heated and thermoformed into a three-dimensional in-mold human-machine interface. Printing took just over an hour — 33 minutes for the AG-550EI silver layer and 40 for the D260EI dielectric — with no traditional screen-printing tooling, and an Arduino interface circuit was printed to validate the connected sensor.
About the speaker:
* Speaker: Huy Nguyen
* Company: Voltera
* Event: Sustainable Electronics RESHAPED 2026 | Berlin
* Location: Estrel, Berlin
Sustainable Electronics RESHAPED | Berlin
📅 Save the date: 20 and 21 October 2027
📍 Berlin, Germany
📋 Info: https://www.techblick.com/sustainableelectronicsreshaped
#SilverInkElectrodes, #DielectricInsulation, #ThermoformingBuck, #ArduinoInterface, #InMoldElectronics, #PrintedElectronics
About this talk
→ Thermoformable Printed Circuits for In-Mold Human-Machine Interfaces · Huy Nguyen · Sustainable Electronics RESHAPED 2026 Berlin


