top of page

Jarne Machiels

Avery Dennison

* All members of the platform can watch the entire presentation.

 

Please register to become a member.

Jarne Machiels | Avery Dennison: Rubber, acrylic or silicone: which pressure-sensitive adhesive survives temperature, solvents and cure time in flexible electronics?

03:44 - 05:16

Other snippets from this talk

Summary of the clip:

Rubber, acrylic or silicone: which pressure-sensitive adhesive survives temperature, solvents and cure time in flexible electronics?

Rubber adhesives, familiar from packaging and duct tape, stick from the very first bond: excellent initial tack and bonding to all kinds of substrates. That instant grab is their selling point. The trade-off arrives later — resistance to temperature, to solvents and so on is quite limited, which narrows the process window once a flexible hybrid device sees reflow, cleaning or harsh service conditions.

Acrylics can be coated by UV hot melt, water-based dispersion or solvent routes, each with different characteristics. Generally they resist temperature, UV and moisture well — the exception being dispersion-based acrylics, coated in water. The catch is time: reaching final bond strength takes 24 hours, a delay that matters for inline processing and fast throughput.

Silicone adhesive is something special: quite inert, it sticks to everything, even to silicones, and withstands up to 260 °C. Those properties justify its use where nothing else works. But it comes with a price, and the adhesion level is limited — so specifying silicone means trading peak bond strength for thermal headroom.

In this short video, you can learn:
* Rubber gives the best initial tack and substrate versatility but the weakest temperature and solvent resistance.
* Acrylic adhesives resist temperature, UV and moisture, yet take 24 hours to reach final bond strength.
* Silicone sticks even to silicones and withstands 260 °C, at the cost of a limited adhesion level.

📋 **Clip Abstract** Three pressure-sensitive adhesive chemistries — rubber, acrylic and silicone — are compared on initial tack, thermal and solvent resistance, and time to final bond strength. That baseline then feeds into an ink-adhesive compatibility study for flexible hybrid electronics.

About the speaker:
* Speaker: Jarne Machiels
* Company: Avery Dennison
* Event: Electronics RESHAPED 2026 | Berlin
* Location: Estrel, Berlin

USA: The Future of Electronics RESHAPED | USA
📅 Save the date: 9 and 10 June 2027
📍 Mountain View, California (Silicon Valley)
📋 Info: https://www.techblick.com/electronicsreshapedusa

Europe
The Future of Electronics RESHAPED | Berlin
📅 Save the date: 20 and 21 October 2027
📍 Berlin, Germany
📋 Info: https://www.techblick.com/electronicsreshaped

#PressureSensitiveAdhesive, #InitialTack, #SiliconeAdhesive, #UVHotMelt, #FlexibleHybridElectronics, #PrintedElectronics

This is a highlight of the presentation:

Direct Contact, No Failures: Mapping Ink/Adhesive Compatibility in Flexible Hybrid Electronics beyond the Holy Grail

​

21 and 22 OCT 2026

Estrel, Berlin

Organised By:

TechBlick

​

More Highlights from the same talk.

04:22 - 06:22

Can one adhesive tape work on every printed ink — silver, copper, carbon — or are 50-plus adhesives really needed?

Can one adhesive tape work on every printed ink — silver, copper, carbon — or are 50-plus adhesives really needed?

More than 50 different adhesive technologies were tested with a wide range of market inks. Adhesive was applied on top of the ink, with high humidity and sheet resistance measured in time. This two-year study mapped what interactions and degradation occur or do not occur across ink-adhesive combinations.

Two main parameters emerged. The ink—copper, silver, carbon particles—and its binder influence final performance. On the adhesive side, rubber, silicone and acrylic, the coating process used, and components added for certain properties all interact. The study found these factors can influence each other, so performance depends on the full combination.

At the start, the study looked for a one-fit-for-all adhesive usable on all inks. There is no holy trail solution. Each ink-adhesive combination is unique, with chemical degradation processes and reactions depending on what is in the ink or adhesive. Crucially, this can be measured: starting from an ink, you do not need to know what it is or which binder is inside.

In this short video, you can learn:
* More than 50 adhesive technologies were tested across a wide range of inks, with humidity and sheet resistance measured in time.
* No single adhesive works for all inks; ink particles, binder, adhesive chemistry and coating all interact.
* The key result is that interactions can be measured from the ink, without knowing the ink or its binder.

📋 **Clip Abstract** A two-year study tested more than 50 adhesive technologies with a wide range of inks, applying adhesive over the ink and measuring sheet resistance under high humidity. It found no one-fit-for-all adhesive: each ink-adhesive combination is unique, with ink particles, binder, adhesive chemistry and coating interacting through chemical degradation or reactions.

About the speaker:
* Speaker: Jarne Machiels
* Company: Avery Dennison
* Event: nnovation Festival: Additive, Printed, Sustainable Electronics, MicroLEDs and AR/VR Displays, Perovskites | July 2026
* Location: Online Platform

Annual access to our onsite event(s), all online events and a library featuring over 1800 presentations (recordings + PDF) across all our onsite and onsite events and technology areas. Join us and over 2000 members from around the world now.
Explore and join now --> https://www.techblick.com/

#InkAdhesiveCompatibility, #SheetResistanceMonitoring, #CopperSilverCarbonInks, #AdhesiveDegradation, #PrintedElectronics, #FlexibleElectronics

05:12 - 06:40

What causes sheet resistance drift when pressure-sensitive adhesives are placed in direct contact with printed functional inks?

What causes sheet resistance drift when pressure-sensitive adhesives are placed in direct contact with printed functional inks?

Adhesive chemistry meets printed connectivity through ion migration and adhesive components that attack the binder of a functional ink. The measurable result is sheet resistance drift: resistance can increase until the printed sensor or medical device no longer works. The compatibility question is therefore not cosmetic; it is whether direct adhesive contact changes functional ink performance enough to cause failure.

To answer that, a method was developed with IMAT—a materials research institute of University Hasselt and IMEC—to measure sheet resistance drift when all kinds of adhesives are applied to a functional ink. The method can also integrate accelerated aging tests. Medical testing uses 37°C; automotive testing uses the 85/85 condition. This turns adhesive contact into a measurable ink-performance variable rather than an assumed compatibility.

Over the last few years, many inks and adhesives were tested using this approach. The lab team’s work produced a practical way to observe how adhesive contact alters functional ink performance and to ask how ink functionality can be secured. The study maps compatibility beyond a single adhesive, because direct contact failures depend on ink chemistry, adhesive chemistry, and aging conditions.

In this short video, you can learn:
* Ion migration and adhesive components attacking a functional ink’s binder can make sheet resistance drift upward until printed sensors or medical devices fail.
* A method developed with IMAT measures sheet resistance drift when adhesives are applied to functional inks and can include accelerated aging.
* The test matrix covers many inks and adhesives, with 37°C for medical and 85/85 for automotive aging conditions.

📋 **Clip Abstract** Adhesive contact can alter printed ink performance through ion migration and binder attack, causing sheet resistance drift and device failure. A measurement method developed with IMAT tracks that drift across many ink/adhesive combinations and accelerated aging conditions, including 37°C medical and 85/85 automotive tests.

About the speaker:
* Speaker: Jarne Machiels
* Company: Avery Dennison
* Event: Electronics RESHAPED 2026 | Berlin
* Location: Estrel, Berlin

USA: The Future of Electronics RESHAPED | USA
📅 Save the date: 9 and 10 June 2027
📍 Mountain View, California (Silicon Valley)
📋 Info: https://www.techblick.com/electronicsreshapedusa

Europe
The Future of Electronics RESHAPED | Berlin
📅 Save the date: 20 and 21 October 2027
📍 Berlin, Germany
📋 Info: https://www.techblick.com/electronicsreshaped

#InkAdhesiveCompatibility, #SheetResistanceDrift, #FunctionalInkBinder, #AcceleratedAgingTests, #FlexibleHybridElectronics, #PrintedElectronics

09:23 - 11:18

How do you bond a cover tape to a carbon-ink PTC heater without oxidation, bubbling or electrical drift?

How do you bond a cover tape to a carbon-ink PTC heater without oxidation, bubbling or electrical drift?

In the battery-management PTC heater example, a partner laminates an adhesive to a 75 micron polyimide film. The carbon ink must not degrade, and the copper contacts must not oxidize over time. Because heat is applied, no bubble formation can occur between the polyimide film and the heater. This build is tested according to the 8585 standard.

The second application, with CRM Group in Liège, Belgium, is a matrix of functional heaters for active camouflage in defense. They use FD0300, a single coated PET film with a specific pure acrylic adhesive that is compatible with the inks. The film itself also protects against humidity and certain mechanical stresses.

Selecting a cover tape means weighing mechanical, thermal and chemical properties together — it is always an and story, not a single-property choice. The ink, the adhesive, the substrate film and the applied heat all interact, so compatibility has to be qualified per application rather than assumed.

In this short video, you can learn:
* A battery-management PTC heater needs a laminating adhesive that protects carbon ink and copper contacts from degradation and oxidation at 75 micron polyimide thickness.
* Heat applied during lamination must not create bubbles between the polyimide film and the heater, and the build is qualified to the 8585 standard.
* FD0300 pairs a single coated PET film with a pure acrylic adhesive compatible with inks, adding humidity and mechanical protection for active-camouflage heaters.

📋 **Clip Abstract** Two cover-tape cases show what drives adhesive selection in printed heaters: a battery-management PTC heater on 75 micron polyimide where carbon ink, copper contacts and bubble-free lamination must all survive, and FD0300, a single coated PET film with pure acrylic adhesive used by CRM Group for active-camouflage heater matrices. Mechanical, thermal and chemical properties combine, so cover tape choice is always an and story.

About the speaker:
* Speaker: Jarne Machiels
* Company: Avery Dennison
* Event: nnovation Festival: Additive, Printed, Sustainable Electronics, MicroLEDs and AR/VR Displays, Perovskites | July 2026
* Location: Online Platform

Annual access to our onsite event(s), all online events and a library featuring over 1800 presentations (recordings + PDF) across all our onsite and onsite events and technology areas. Join us and over 2000 members from around the world now.
Explore and join now --> https://www.techblick.com/

#PTCHeaterLamination, #CarbonInkDegradation, #CopperContactOxidation, #AcrylicAdhesiveCoverTape, #PrintedHeaters, #FlexibleElectronics


About this talk

→ Direct Contact, No Failures: Mapping Ink/Adhesive Compatibility in Flexible Hybrid Electronics beyond the Holy Grail · Jarne Machiels · The Future of Electronics RESHAPED 2026 Berlin


Other talks by Jarne Machiels


More highlights from Jarne Machiels

More Snippets
CONTACT US

KGH Concepts GmbH

Mergenthalerallee 73-75, 65760, Eschborn

+49 17661704139

admin@techblick.com

TechBlick is owned and operated by KGH Concepts GmbH

Registration number HRB 121362

VAT number: DE 337022439

  • LinkedIn
  • YouTube

Sign up for our newsletter to receive updates on our latest speakers and events AND to receive analyst-written summaries of the key talks and happenings in our events.

Thanks for submitting!

© 2026 by KGH Concepts GmbH

bottom of page