Jessica Pereira | University of Southampton: How stable are copper inks after 250 days in air and 85/85 accelerated aging?
13:46 - 14:37
Other snippets from this talk
Summary of the clip:
How stable are copper inks after 250 days in air and 85/85 accelerated aging?
The material becomes conductive by pressure alone, which enables conductive samples on pliable yet temperature-sensitive substrates. For ink stability, samples were left in air under ambient conditions for 250 days. The observed change was small: a 4% change in resistance. That is the stability result reported so far for the inks.
Accelerated aging was also performed, but still on paper-based substrates. The conditions were 85 degrees and 85% humidity, which the speaker noted is a lot of humidity for paper-based substrates. Aging ran for only 75 hours and resulted in an R over R-nought value of about 6%.
The conclusion was that the material is there, but the formulation keeps changing, so there is a lot that can progress. Pressure alone, rather than temperature, is the route to conductivity and to pliable temperature-sensitive substrates. Stability evidence spans 250 days in ambient air and 75 hours at 85/85 on paper.
In this short video, you can learn:
* Inks left in ambient air for 250 days showed only a 4% change in resistance.
* Accelerated aging at 85 degrees and 85% humidity for 75 hours on paper-based substrates gave R/R-nought of about 6%.
* The material is considered there, but formulation changes leave room to progress.
π **Clip Abstract** Pressure alone can make the material conductive, enabling pliable temperature-sensitive substrates. The inks showed a 4% resistance change after 250 days in air, while 75 hours at 85 degrees and 85% humidity on paper-based substrates gave R/R-nought of about 6%.
About the speaker:
* Speaker: Jessica Pereira
* Company: University of Southampton
* Event: Electronics RESHAPED 2026 | Berlin
* Location: Estrel, Berlin
USA: The Future of Electronics RESHAPED | USA
π
Save the date: 9 and 10 June 2027
π Mountain View, California (Silicon Valley)
π Info: https://www.techblick.com/electronicsreshapedusa
Europe
The Future of Electronics RESHAPED | Berlin
π
Save the date: 20 and 21 October 2027
π Berlin, Germany
π Info: https://www.techblick.com/electronicsreshaped
#CopperInkStability, #AcceleratedAging, #PaperBasedSubstrates, #PressureInducedConductivity, #PrintedElectronics, #ConductiveInks
This is a highlight of the presentation:
Room Temperature Compressed Copper: A Scalable Route to Highly Conductive Films for Printed Electronics
More Highlights from the same talk.
02:50 - 03:55
How does a red-seaweed polymer make copper particles, and which carrageenan loading performs best?
How does a red-seaweed polymer make copper particles, and which carrageenan loading performs best?
Kappa carrageenan, derived from red seaweeds and commonly used as a gelling or thickening agent in cosmetics, pharmaceuticals and food, is dissolved in water. Copper is then added, with pH adjustments, driving an oxidation-reduction reaction that yields red copper particles. SEM shows their shape.
Particle sizes can be varied by several factors: pH, relative proportions of added agents, how much copper is added, the copper source, and the relative proportions of reducing agent. Three main particle ranges were worked with, and all are described as good for the applications under focus.
Of the three ranges, the red sampleβwith 1% carrageenan weight by volumeβis identified as probably the best so far. It gives a very good balance between particle sizes, the stability achieved, and the electrical properties obtainable.
In this short video, you can learn:
* Kappa carrageenan from red seaweeds is dissolved in water, then copper and pH adjustments trigger an oxidation-reduction reaction yielding red copper particles.
* Copper particle size is tuned by pH, agent proportions, copper amount and source, and reducing-agent proportion, giving three main ranges.
* The 1% carrageenan weight-by-volume formulation is the best so far, balancing particle size, stability and electrical properties.
π **Clip Abstract** Kappa carrageenan, a red-seaweed-derived gelling and thickening agent, is dissolved in water and combined with copper under pH adjustment to drive an oxidation-reduction reaction producing red copper particles. Particle size is varied through pH, agent and copper proportions, copper source and reducing agent, with a 1% carrageenan weight-by-volume formulation giving the best balance of size, stability and electrical properties.
About the speaker:
* Speaker: Jessica Pereira
* Company: University of Southampton
* Event: Electronics RESHAPED 2026 | Berlin
* Location: Estrel, Berlin
USA: The Future of Electronics RESHAPED | USA
π
Save the date: 9 and 10 June 2027
π Mountain View, California (Silicon Valley)
π Info: https://www.techblick.com/electronicsreshapedusa
Europe
The Future of Electronics RESHAPED | Berlin
π
Save the date: 20 and 21 October 2027
π Berlin, Germany
π Info: https://www.techblick.com/electronicsreshaped
#KappaCarrageenan, #CopperParticleSizing, #OxidationReduction, #ElectricalProperties, #PrintedElectronics, #AdditiveElectronics
09:59 - 11:28
What sheet resistance can compressed copper ink reach on paper, and can a rolling mill scale it?
What sheet resistance can compressed copper ink reach on paper, and can a rolling mill scale it?
Proof-of-concept paper circuits passed current and lit something. Cross-sections show compressed copper films of about seven to ten microns, thinner than normally expected. On A4, sheet resistance is about 10 milliohms per square or less, averaging 10 milliohms per square. On filter paper, with a different fiber structure, it rises to about 20 to 30 milliohms per square.
The initial hydraulic bench press limited sample size. The team moved to a rolling mill, described as like a pasta maker but applying much higher pressures, typically used in jewelry making. Two rollers are aligned to the required distance, set by sample thickness, substrate thickness and deposited copper thickness. A sample goes in on the substrate nonconductive and comes out conductive.
This roller-based route addresses the sample-size constraint of the hydraulic bench press. A4 films reach about 10 milliohms per square; filter-paper films reach 20 to 30. The process is simple: adjust rollers, roll the printed substrate, and the output is conductive. One student is now focusing beyond the printing aspect.
In this short video, you can learn:
* A4 paper films achieved about 10 milliohms per square or less, averaging 10 milliohms per square.
* Filter paper gave 20 to 30 milliohms per square due to a different fiber structure.
* Replacing a hydraulic bench press with a jewelry-industry rolling mill addresses sample-size limits and turns a nonconductive input into a conductive output.
π **Clip Abstract** Compressed copper films on A4 paper reached about 10 milliohms per square, while filter paper reached 20 to 30 milliohms per square. A rolling mill, adapted from jewelry making, aligns rollers to the sample, substrate and copper thickness, turning a nonconductive input into a conductive output without the hydraulic pressβs sample-size constraint.
About the speaker:
* Speaker: Jessica Pereira
* Company: University of Southampton
* Event: Electronics RESHAPED 2026 | Berlin
* Location: Estrel, Berlin
USA: The Future of Electronics RESHAPED | USA
π
Save the date: 9 and 10 June 2027
π Mountain View, California (Silicon Valley)
π Info: https://www.techblick.com/electronicsreshapedusa
Europe
The Future of Electronics RESHAPED | Berlin
π
Save the date: 20 and 21 October 2027
π Berlin, Germany
π Info: https://www.techblick.com/electronicsreshaped
#CompressedCopper, #RollingMill, #SheetResistance, #PaperCircuits, #PrintedElectronics, #AdditiveElectronics
05:23 - 07:20
How close is compressed copper to 25 Β΅m commercial foil, and what limits its conductivity?
How close is compressed copper to 25 Β΅m commercial foil, and what limits its conductivity?
SEM imaging of three particle-size variations shows particles interlinking like pieces of a jigsaw puzzle as magnification rises from left to right. The middle formulation, the best so far, shows porosity below 5%, which should favour higher conductivity. The bottom sample is clearly more porous, and that is reflected in the measured conductive values.
Probing resistivity across temperature ranges gives a good linear relationship for metal-like behaviour, and that is exactly what these films showed. Blue and red are the printed material; brown is commercial copper foil of equivalent thickness. The films are 25 micrometres thick, matched against 25-micrometre foil. The 1.5% sample is slightly less linear, consistent with higher porosity.
In numbers, the first two materials are about 1.5 times more resistive than commercial copper foil β described as pretty good for this type of material β while the 1.5% formulation sits one order of magnitude off in conductivity. With conductive properties established, the next step was to use the copper as an ink, deposit it and measure.
In this short video, you can learn:
* Particle-size formulation governs film porosity, with the middle sample below 5% and the most porous sample measurably less conductive.
* Resistivity versus temperature is linear, matching metal-like behaviour, and is benchmarked against 25-micrometre commercial copper foil.
* The best two formulations are about 1.5 times more resistive than commercial copper foil, while the 1.5% sample is an order of magnitude off.
π **Clip Abstract** Compressed copper films 25 micrometres thick are benchmarked against commercial copper foil of the same thickness, showing linear resistivity-temperature behaviour and under 5% porosity in the best formulation. The top two formulations are about 1.5 times more resistive than foil, while the more porous 1.5% sample loses an order of magnitude in conductivity, motivating the move to ink deposition.
About the speaker:
* Speaker: Jessica Pereira
* Company: University of Southampton
* Event: Electronics RESHAPED 2026 | Berlin
* Location: Estrel, Berlin
USA: The Future of Electronics RESHAPED | USA
π
Save the date: 9 and 10 June 2027
π Mountain View, California (Silicon Valley)
π Info: https://www.techblick.com/electronicsreshapedusa
Europe
The Future of Electronics RESHAPED | Berlin
π
Save the date: 20 and 21 October 2027
π Berlin, Germany
π Info: https://www.techblick.com/electronicsreshaped
#CompressedCopper, #CopperInk, #SEMPorosity, #ResistivityTemperatureLinearity, #PrintedElectronics, #ConductiveInks
About this talk
β Room Temperature Compressed Copper: A Scalable Route to Highly Conductive Films for Printed Electronics Β· Jessica Pereira Β· The Future of Electronics RESHAPED 2026 Berlin


