top of page

Jochen christiaens

IMAGEXPERT LLC

* All members of the platform can watch the entire presentation.

 

Please register to become a member.

Jochen christiaens | IMAGEXPERT LLC: Is the ink failing to jet, or is your process window too narrow — and where is the sweet spot?

04:17 - 05:50

Other snippets from this talk

Summary of the clip:

Is the ink failing to jet, or is your process window too narrow — and where is the sweet spot?

Start with drop watching: observe the ink being pushed through a nozzle and ask whether the drop is large enough, flying fast enough, and continuously jetting. Watch for nozzles dropping out after some time and for satellites. These are the first parameters to check before tuning anything else.

Then vary the waveform: change timing, volt levels and frequency. Also adjust ink temperature—warmer or colder—and change ink supply toward the head. Each setting influences jetting stability. In this phase you can find the window of opportunity: the worst setting, the best setting, and somewhere between them the sweet spot.

With that sweet spot, optimize continuously and speed up the process. Move from general jetting to different frequencies and different drop speeds, and identify where your ink drops out. That drop-out point is where some customers stop and go back into the kitchen, saying “It’s not jetting.”

In this short video, you can learn:
* Drop watching checks whether a drop is large enough, fast enough and continuously jetting, and flags nozzles that drop out or produce satellites.
* Waveform timing, volt levels, frequency, ink temperature and ink supply toward the head all influence jetting stability.
* Testing different frequencies and drop speeds identifies where the ink drops out, revealing the limits beyond the sweet spot.

📋 **Clip Abstract** The clip shows how drop watching and controlled parameter changes—waveform timing, volt levels, frequency, temperature and ink supply—are used to find a stable jetting window. It then explains how to move from a sweet spot to different frequencies and drop speeds to find where the ink drops out.

About the speaker:
* Speaker: Jochen christiaens
* Company: IMAGEXPERT LLC
* Event: Electronics RESHAPED 2026 | Berlin
* Location: Estrel, Berlin

USA: The Future of Electronics RESHAPED | USA
📅 Save the date: 9 and 10 June 2027
📍 Mountain View, California (Silicon Valley)
📋 Info: https://www.techblick.com/electronicsreshapedusa

Europe
The Future of Electronics RESHAPED | Berlin
📅 Save the date: 20 and 21 October 2027
📍 Berlin, Germany
📋 Info: https://www.techblick.com/electronicsreshaped

#DropWatching, #WaveformTuning, #JettingStability, #SatelliteDrops, #InkjetPrinting, #PrintedElectronics

This is a highlight of the presentation:

From Defect Detection to Root Cause Resolution: Practical Methods for Verifying, Evaluating, and Optimizing Inkjet Print Quality

​

21 and 22 OCT 2026

Estrel, Berlin

Organised By:

TechBlick

​

More Highlights from the same talk.

08:13 - 10:02

Higher voltage or retimed waveform: which drives drop velocity, and when do satellites appear?

Higher voltage or retimed waveform: which drives drop velocity, and when do satellites appear?

Timing and voltage combine to shape the drop. Timing changes volume, shape and speed; voltage pushes the drop out of the nozzle faster, raising velocity, but it has a limit. At a certain volt level, the extra voltage produces satellites—smaller drops trailing the main drop—which undermine straight lines with clean edges.

Satellites are not universally unacceptable. In a coating, a full layer may absorb them and make them disappear, so a single drop is not necessarily required. One or two satellites can be perfectly fine, depending on the application. So the acceptable satellite outcome depends on the application.

Production speed sets the frequency you need to test. The image shows different frequencies producing more or fewer drops in the same line, and testing establishes where perfect drops end and satellites begin. On the right side, the last five-to-two region has more satellites, so it is not an ideal area on which to focus.

In this short video, you can learn:
* Voltage raises drop velocity but beyond a certain level creates trailing satellites.
* Timing changes drop volume, shape and speed, while voltage pushes the drop out of the nozzle faster.
* Acceptable satellite count depends on application; a full coating layer can absorb satellites, while a straight line with clean edges cannot tolerate them.

📋 **Clip Abstract** The clip separates waveform timing from voltage: timing alters drop volume, shape and speed, while voltage raises velocity until trailing satellites appear. It then ties acceptable satellite levels to the application—coating versus line—and uses frequency sweeps to find where perfect drops give way to satellites as production speed rises.

About the speaker:
* Speaker: Jochen christiaens
* Company: IMAGEXPERT LLC
* Event: Electronics RESHAPED 2026 | Berlin
* Location: Estrel, Berlin

USA: The Future of Electronics RESHAPED | USA
📅 Save the date: 9 and 10 June 2027
📍 Mountain View, California (Silicon Valley)
📋 Info: https://www.techblick.com/electronicsreshapedusa

Europe
The Future of Electronics RESHAPED | Berlin
📅 Save the date: 20 and 21 October 2027
📍 Berlin, Germany
📋 Info: https://www.techblick.com/electronicsreshaped

#InkjetDropVelocity, #SatelliteDrops, #WaveformTiming, #FrequencySweep, #InkjetPrinting, #PrintedElectronics

13:32 - 14:35

Reformulating the ink: when is it justified, and why can't you resume optimizing from where you stopped?

Reformulating the ink: when is it justified, and why can't you resume optimizing from where you stopped?

Process parameters define what remains changeable, so fine-tuning is only possible up to a point. The decision point is reformulation: once an ink is reformulated, you must go back through the whole process from the start. You cannot jump in at the point where you left off.

A formulation made to address wettability on a substrate still changes how the drop is formed from the nozzle. That is why the process must be reviewed again. Keep the print samples, images and data from first trials and compare them against the second ink formulation to judge whether the new formulation is good or bad.

The conclusion is direct: it is impossible to jump in at a certain level and say you will always be optimizing from here on. Reformulation resets the optimization path, and only a before-and-after comparison with the original trial data can show whether the reformulation helped or hurt.

In this short video, you can learn:
* Reformulating an ink requires restarting the whole process rather than resuming from the previous optimization point.
* A wettability-driven formulation change also alters drop formation from the nozzle.
* First-trial print samples, images and data provide the baseline for judging a second formulation.

📋 **Clip Abstract** The clip sets the boundary between process-parameter fine-tuning and ink reformulation. It explains why a new formulation, even one aimed at substrate wettability, forces a full process restart and must be judged against the original print samples, images and trial data.

About the speaker:
* Speaker: Jochen christiaens
* Company: IMAGEXPERT LLC
* Event: Electronics RESHAPED 2026 | Berlin
* Location: Estrel, Berlin

USA: The Future of Electronics RESHAPED | USA
📅 Save the date: 9 and 10 June 2027
📍 Mountain View, California (Silicon Valley)
📋 Info: https://www.techblick.com/electronicsreshapedusa

Europe
The Future of Electronics RESHAPED | Berlin
📅 Save the date: 20 and 21 October 2027
📍 Berlin, Germany
📋 Info: https://www.techblick.com/electronicsreshaped

#InkReformulation, #SubstrateWettability, #DropFormation, #TrialDataComparison, #InkjetPrinting, #PrintedElectronics

11:11 - 13:15

Why does fixing a drop too fast destroy coating homogeneity, and where is your tolerance border?

Why does fixing a drop too fast destroy coating homogeneity, and where is your tolerance border?

A heated table raises substrate temperature so solvent evaporates quickly and the drop pins, preventing excessive wetting. With UV curing, printhead-to-dryer distance sets how fast the drop is fixed. If pinning is too heavily focused on the freshly printed drop, the ink may dry too quickly and fail to form nicely closed homogenic coating areas.

The result can be structured areas rather than the closed layer you want, so the final result of that layer must be considered. Finding what really drives the defect means playing with all process parameters: adding pretreatment or changing pretreatment parameters, and changing timing or substrate temperature. These variables all affect how print quality is affected.

Trade-offs matter: optimizing jetting for no satellites is not always desirable, because making the drop fly slower can worsen print quality. If a process parameter must change to a level unacceptable for the final process, you have reached the outside borders. Those borders mark the limit for acceptable process changes.

In this short video, you can learn:
* Heated substrates and UV printhead-to-dryer distance control how quickly a drop pins and fixes.
* Over-focused pinning can prevent nicely closed homogenic coating areas and leave structured areas.
* Defect resolution requires testing pretreatment, timing and substrate temperature while accepting jetting trade-offs such as slower drops worsening print quality.

📋 **Clip Abstract** This clip examines how substrate heating and UV curing distance fix an inkjet drop, and how over-rapid pinning can prevent homogenic coating areas. It frames defect resolution as a trade-off exercise across pretreatment, timing and substrate temperature, ending at the outside borders where process changes become unacceptable.

About the speaker:
* Speaker: Jochen christiaens
* Company: IMAGEXPERT LLC
* Event: Electronics RESHAPED 2026 | Berlin
* Location: Estrel, Berlin

USA: The Future of Electronics RESHAPED | USA
📅 Save the date: 9 and 10 June 2027
📍 Mountain View, California (Silicon Valley)
📋 Info: https://www.techblick.com/electronicsreshapedusa

Europe
The Future of Electronics RESHAPED | Berlin
📅 Save the date: 20 and 21 October 2027
📍 Berlin, Germany
📋 Info: https://www.techblick.com/electronicsreshaped

#DropPinning, #HomogenicCoating, #PrintheadDryerDistance, #SatelliteTradeoff, #InkjetPrintQuality, #PrintedElectronics


About this talk

→ From Defect Detection to Root Cause Resolution: Practical Methods for Verifying, Evaluating, and Optimizing Inkjet Print Quality · Jochen christiaens · The Future of Electronics RESHAPED 2026 Berlin


Other talks by Jochen christiaens

More Snippets
CONTACT US

KGH Concepts GmbH

Mergenthalerallee 73-75, 65760, Eschborn

+49 17661704139

admin@techblick.com

TechBlick is owned and operated by KGH Concepts GmbH

Registration number HRB 121362

VAT number: DE 337022439

  • LinkedIn
  • YouTube

Sign up for our newsletter to receive updates on our latest speakers and events AND to receive analyst-written summaries of the key talks and happenings in our events.

Thanks for submitting!

© 2026 by KGH Concepts GmbH

bottom of page