Jochen Christiaens | ImageXpert: How much print quality is lost by jetting with a printhead's standard waveform?
14:47 - 17:15
Other snippets from this talk
Summary of the clip:
How much print quality is lost by jetting with a printhead's standard waveform?
During flight toward the substrate, the jetting sequence produces a first impulse drop, then second and third drops that vary by printhead. Behind them, satellites scatter and misting forms, which is not visible during the event but appears after a day throughout the machine. When printing silver inks or other costly materials, that material must land on the substrate, not inside the machine. Waveform optimization is therefore important: it controls the electrical impulse on the piezos and lets you see whether those unwanted drops disappear, worsen or improve.
The analysis can leave out the large dots and keep only the smaller satellites or misting, so you focus on those parts and gather data while tweaking waveforms. On the waveform display, green arrows left, right, up and down mark areas you can adjust manually or automize, producing different printout results. From those results, select the area with one main drop farthest downwards, because it flies fastest. Then optimize flight speed, drop size volume and straight-line flight, avoiding drops that fly in any direction.
Premium manufacturers deliver standard waveforms, yet a customer case shows the difference between using one and optimizing it. With the standard waveform, the result is not good to jet: print quality is mediocre, drops appear all over, and the drops have wave-like, different speeds between them. After waveform optimization, the bottom result is homogeneously the same across the print, which is exactly what is needed. That contrast is why waveform optimization is key for jetting.
In this short video, you can learn:
* Standard waveforms can leave satellites and misting that appear after a day throughout the machine, which is especially costly with silver inks.
* Waveform optimization tweaks the electrical impulse on piezos, edits waveform regions manually or automized, and shows whether drops disappear, worsen, improve, and whether flight speed, drop size volume, and straightness change.
* A customer case showed standard-waveform jetting with mediocre print quality, drops all over and different speeds between drops, while optimization produced a homogeneous result.
📋 **Clip Abstract** Drop formation during flight includes main drops, satellites and misting, and waveform optimization changes whether unwanted drops disappear, worsen or improve. A customer case contrasts a standard waveform's mediocre print quality, drops all over and different speeds between drops with a homogeneous result after optimization.
About the speaker:
* Speaker: Jochen Christiaens
* Company: ImageXpert
* Event: The Future of Electronics RESHAPED 2025
* Location: Estrel, Berlin
🗓️ Save the date for the next Future of Electronic RESHAPED conference and exhibition
USA | Mountain View | 9-10 June 2027 : https://www.techblick.com/electronicsreshapedusa
Europe | Berlin | 20-21 October 2027: https://www.techblick.com/electronicsreshaped
#WaveformOptimization, #SatelliteDrops, #PiezoImpulse, #SilverInks, #PrintedElectronics, #AdditiveElectronics
This is a highlight of the presentation:
Selecting the Right Inkjet Printhead for Advanced Electronics Applications
More Highlights from the same talk.
05:19 - 07:05
Why are 80–90 cPs battery inks now jetting, and how far beyond the old 10 cPs inkjet limit can formulators go?
Why are 80–90 cPs battery inks now jetting, and how far beyond the old 10 cPs inkjet limit can formulators go?
Battery coating is another higher-viscosity application, where thick liquids must be jetted, partially printed over larger distances and onto 3D-shaped forms. Viscosities under 80, 90 cPs at jetting temperature would be nice here. This area is often more of a formulation challenge: things with good functionality usually have high viscosity. Using rheological behavior and temperature can get that viscosity down into an injectable area.
If formulation can be changed to a lower viscosity range, say 40, 50 cPs, a wider selection of printheads can jet it. Until some time ago, people generally said 10 cPs was what inkjet could do. It is way more than that by now; hundreds are possible, and the trend is going toward higher viscosity. Industrial applications are moving from analog spray coating or even print processes into inkjet.
They want to investigate what is possible, scale down the supply chain, reduce process complexity and save materials. Spray applications, screen printing or flex have lots of additional consumables, which are costly in themselves. Conductive inks follow the same thing, though they are less viscous than adhesives. The trend is going toward higher viscosity, so formulation and printhead selection determine what can be jetted.
In this short video, you can learn:
* Battery coating demands thick liquids, larger distances and 3D-shaped forms, with 80–90 cPs at jetting temperature described as desirable.
* Rheological behavior and temperature can lower high-viscosity functional materials into an injectable range, while 40–50 cPs formulations open a wider printhead selection.
* The old 10 cPs inkjet limit is far exceeded, with hundreds of cPs now possible and industrial analog spray, screen and flex processes moving toward inkjet to reduce consumables and save materials.
📋 **Clip Abstract** This clip explains why battery coating and conductive inks are pushing inkjet beyond the long-standing 10 cPs viscosity assumption. It covers 80–90 cPs battery inks at jetting temperature, 40–50 cPs formulation options, rheological temperature control, wider printhead selection, and the move from analog spray, screen and flex processes to inkjet for lower complexity and material savings.
About the speaker:
* Speaker: Jochen Christiaens
* Company: ImageXpert
* Event: The Future of Electronics RESHAPED 2025
* Location: Estrel, Berlin
🗓️ Save the date for the next Future of Electronic RESHAPED conference and exhibition
USA | Mountain View | 9-10 June 2027 : https://www.techblick.com/electronicsreshapedusa
Europe | Berlin | 20-21 October 2027: https://www.techblick.com/electronicsreshaped
#BatteryCoating, #ConductiveInks, #InkjetPrintheads, #HighViscosityJetting, #PrintedElectronics, #AdditiveElectronics
06:45 - 08:50
How can the same printing technology create both nanometer-scale AR waveguide features and hundred-micron protective coatings for car bodies?
How can the same printing technology create both nanometer-scale AR waveguide features and hundred-micron protective coatings for car bodies?
The selection of an inkjet printhead is fundamentally dictated by the target application, particularly the required drop size and resulting layer thickness. For high-precision applications like Thin Film Encapsulation (TFE) of perovskite or OLED devices, the goal is to deposit uniform, defect-free layers that are only a few hundred nanometers thick. This demands printheads capable of generating extremely small and consistent droplets, typically in the 1-to-3-picoliter range, where precise control over drop volume and placement is paramount.
A key example of this high-precision regime is the fabrication of next-generation augmented reality (AR) optics. Inkjet is used to deposit highly uniform layers of resist material for Nanoimprint Lithography (NIL), which defines the nanoscale diffractive features of a waveguide. Achieving the required uniformity and edge sharpness for these optical components relies on the precise deposition of these small, well-controlled droplets. Any variation in drop size or placement could lead to critical optical defects.
In stark contrast, industrial applications like coating battery assemblies or applying protective layers on automotive parts require a completely different approach. Here, the objective is to deposit thick, robust layers of hundreds of microns using high-viscosity adhesives or coatings, sometimes with viscosities in the hundreds of centipoise. These applications utilize printheads designed for mechanical performance and high throughput, capable of jetting large volumes of challenging fluids, where picoliter precision is secondary to durability and flow rate.
In this short video, you can learn:
* How drop size (from 1 pL to hundreds of pL) dictates the achievable layer thickness and feature resolution.
* The specific inkjet requirements for fabricating advanced optical components like AR waveguides via Nanoimprint Lithography (NIL).
* Why high-viscosity applications, like battery adhesives or automotive coatings, demand a completely different class of printhead technology.
📋 **Clip Abstract** Inkjet printing is not a monolithic technology; the choice of printhead is dictated by the application's required layer thickness and fluid properties. This clip contrasts the picoliter-precision needed for nanometer-scale AR optics with the high-viscosity, high-volume deposition used for micron-scale protective coatings.
🔗 Link in comments 👇
#InkjetPrinting, #PicoliterPrecision, #ARWaveguides, #HighViscosityFluids, #PrintedElectronics, #PerovskiteTechnology
10:21 - 11:42
Why do the smallest drops stop jetting after standby unless ink recirculates through the head?
Why do the smallest drops stop jetting after standby unless ink recirculates through the head?
Printheads are a major topic for inkjet when liquids carry particle loading, including heavier particle loadings. The image on the left shows a gravity feed system: ink flows by gravity from the sub tank into the head, and is jetted from there. With simple heads and simple fluids this is not too much of an issue, but heavier particle loadings change the requirement.
With a titanium dioxide pigment, which has a high density itself, the ink will settle within quite some time. You then have to rotate the ink through the ink system, from the sub tank through the head and back up again, to keep all the ink and particles well suspended. The result shows up in the image on the right side.
On the right side, the differentiation is different drop sizes, so one to three drops generation, and you will see that at the right end of this image. Without recirculation, the smaller drops that are jetted are not jetting after the printhead has had a standby period for some time. Adding recirculation to this definitely helps, as the comparison demonstrates.
In this short video, you can learn:
* A gravity feed system sends ink from the sub tank into the head by gravity alone and jets it from there, which is acceptable for simple heads running simple fluids.
* Titanium dioxide pigment has a high density itself, so it settles within quite some time unless the ink is rotated from the sub tank through the head and back up again to stay suspended.
* In the one to three drops generation, the smaller jetted drops are the ones that fail to jet after a standby period, and adding recirculation definitely helps.
📋 **Clip Abstract** Inkjet liquids carrying heavier particle loading pose a supply question: does gravity feed deliver enough, or must ink be circulated? A comparison of a gravity feed system against recirculation, using a high density titanium dioxide pigment, shows settling and shows that the smaller drops of a one to three drop generation stop jetting after standby until ink is rotated through the head.,Adding recirculation to this definitely helps.
About the speaker:
* Speaker: Jochen Christiaens
* Company: ImageXpert
* Event: The Future of Electronics RESHAPED 2025
* Location: Estrel, Berlin
🗓️ Save the date for the next Future of Electronic RESHAPED conference and exhibition
USA | Mountain View | 9-10 June 2027 : https://www.techblick.com/electronicsreshapedusa
Europe | Berlin | 20-21 October 2027: https://www.techblick.com/electronicsreshaped
#InkRecirculation, #TitaniumDioxidePigment, #GravityFeedSystem, #DropSizeGeneration, #InkjetPrintheads, #PrintedElectronics
About this talk
→ Selecting the Right Inkjet Printhead for Advanced Electronics Applications · Jochen Christiaens · Additive, Printed, Hybrid and Sustainable Electronics Innovations Day 2025
Other talks by Jochen Christiaens
- From Defect Detection to Root Cause Resolution: Practical Methods for Verifying, Evaluating, and Optimizing Inkjet Print Quality · The Future of Electronics RESHAPED 2026 Berlin
- Selecting the Right Inkjet Printhead for Advanced Electronics Applications · The Future of Electronics RESHAPED 2025
More highlights from Jochen Christiaens
- ▶ How can the same printing technology create both nanometer-scale AR waveguide features and hundred-micron protective coatings for car bodies? · Additive, Printed, Hybrid and Sustainable Electronics Innovations Day 2025
- ▶ Your nanoparticle ink keeps clogging the printhead nozzles. Is there a hardware solution you're overlooking? · Additive, Printed, Hybrid and Sustainable Electronics Innovations Day 2025


