top of page

Kai Hohmann

Continental Corporation

* All members of the platform can watch the entire presentation.

 

Please register to become a member.

Kai Hohmann | Continental Corporation: Why does a 50-inch 10K automotive microLED panel need 30 million LEDs and zero bright-pixel failures?

04:36 - 06:50

Other snippets from this talk

Summary of the clip:

Why does a 50-inch 10K automotive microLED panel need 30 million LEDs and zero bright-pixel failures?

The next issue is upscaling production capacity: every microLED takes a lot of time to be produced, and scaling is needed to reduce cost. A pillar-to-pillar automotive display at 50-inch, 10K-class resolution requires about 30 million LEDs. Automotive does not accept a bright pixel at the moment, so that means no failures. These production and cost questions are discussed back and forth.

A 2004 presentation described a new display coming up with thin, lightweight construction, high contrast, no viewing-angle dependency versus LCD at that time, later lower power consumption, high resolution with active matrix and good readability. It eventually listed transparent and potentially flexible attributes—and no cost. Passive matrix was set for production in 2006, active matrix to follow in 2007–8; higher system costs and increased development risk were reasons not to speed up.

For automotive, it took maybe 10 to 12 further years before this product or display was introduced in production—and it was OLED at that time. MicroLED now also has many opportunities and many risks, echoing that earlier comparison. The open questions remain capacity upscaling, zero bright-pixel failures and cost, as automotive discusses them back and forth.

In this short video, you can learn:
* A 50-inch 10K-class pillar-to-pillar automotive panel needs about 30 million microLEDs, and automotive currently accepts no bright-pixel failures.
* MicroLED production is slow per device, so capacity upscaling is tied directly to cost reduction.
* A 2004 display roadmap promised passive-matrix production in 2006 and active-matrix in 2007–8, but higher system costs and development risk were reasons not to speed up, and automotive production took 10 to 12 further years as OLED.

📋 **Clip Abstract** The clip examines automotive microLED display scaling, where a 50-inch 10K-class pillar-to-pillar panel would need about 30 million LEDs and zero bright-pixel failures. It compares microLED's current opportunities and risks with a 2004 display roadmap that promised passive matrix in 2006 and active matrix in 2007–8, but cited higher system costs and development risk before automotive OLED production arrived 10 to 12 years later.

About the speaker:
* Speaker: Kai Hohmann
* Company: Continental Corporation
* Event: MicroLED Connect 2024
* Location: High Tech Campus, Eindhoven, Netherlands

Join the most event MicroLED, AR/VR display and Optical I/O Connect event of the year
Learn more https://www.microledconnect.com/

#MicroLEDCapacity, #BrightPixelFailure, #PillarToPillarDisplay, #ActiveMatrixProduction, #AutomotiveDisplays, #DisplayManufacturing

This is a highlight of the presentation:

Automotive User Experience - Opportunities for MicroLED Displays

MicroLED Connect 2024

​

25-26 September 2024

High Tech Campus, Eindhoven, Netherlands

Organised By:

Metal Grass and TechBlick

​

More Highlights from the same talk.

08:28 - 10:11

Which microLED backplane—CMOS, TFT glass or PCB—fits which automotive display, and why?

Which microLED backplane—CMOS, TFT glass or PCB—fits which automotive display, and why?

There is no single right application: every product has its own requirements, driven mainly by brightness and resolution. MicroLED on silicon uses a CMOS carrier with LEDs packed at a certain density and drivers integrated into the CMOS chip, achieving the highest luminance. Size is limited because nobody will pay for a huge silicon chip; AR and potentially head-up display are cited applications.

MicroLED on TFT glass or TFT backplanes has a larger, lower-density LED array, with separate drivers and chip-on-foil or chip-on-glass assembly. Its size is limited by the LED mounting capacity of the machines, not by an integrated CMOS driver chip. This approach is described as good for direct-view displays.

MicroLED on PCBs uses a PCB carrier at lower resolution, though resolution may slightly increase. Drivers sit on the PCB, and size is effectively unlimited through tiling. The open questions are how close tiles can be and how the gap behind them is handled. Currently this is seen for television.

In this short video, you can learn:
* Brightness and resolution requirements, not a universal rule, determine the backplane choice for each automotive product.
* CMOS delivers the highest luminance but hits size limits because large silicon chips are uneconomical.
* TFT glass suits direct-view displays, while PCB tiling offers scalable size but raises tile-gap questions.

📋 **Clip Abstract** MicroLED backplane choice depends on each product’s brightness and resolution needs rather than a single right application. CMOS offers highest luminance with size limits; TFT glass suits direct-view displays, while PCB tiling scales size but raises tile-gap questions.

About the speaker:
* Speaker: Kai Hohmann
* Company: Continental Corporation
* Event: MicroLED Connect 2024
* Location: High Tech Campus, Eindhoven, Netherlands

Join the most event MicroLED, AR/VR display and Optical I/O Connect event of the year
Learn more https://www.microledconnect.com/

#MicroLEDOnSilicon, #TFTGlassBackplane, #ChipOnFoil, #PCBTiling, #AutomotiveDisplays, #MicroLEDBackplanes

14:57 - 16:45

What are microLED's real automotive advantages and remaining weaknesses versus LCD and OLED?

What are microLED's real automotive advantages and remaining weaknesses versus LCD and OLED?

In automotive, four competing display technologies are compared: LCD with edge backlight, LCD with matrix backlight, OLED and microLED. For microLED, the main benefit is the potential to scale brightness up to the level an application requires. Mechanical robustness is a big automotive topic; LCD has many issues and black-uniformity problems, while microLED is not sensitive. Transparency is also cited as a microLED benefit.

Power consumption remains a drawback and an improvement area. The parts seen so far are not as good as expected, possibly because the drivers are taken and not optimized well for microLEDs. More efficiency evidence is wanted from samples. Cost is a question of scaling and investment in production lines. Smaller LED usage is linked to better wafer and technology utilization.

The automotive case for microLED is therefore split between optical and mechanical advantages and unresolved efficiency and cost. Brightness scaling, robustness, black uniformity and transparency are the claimed benefits. Power consumption, sample evidence, production-line investment and wafer utilization define the remaining work. The comparison keeps LCD edge-backlight, LCD matrix-backlight and OLED as reference points, with efficiency and cost still tied to samples and scale.

In this short video, you can learn:
* MicroLED's cited automotive advantages are brightness scaling, mechanical robustness, black uniformity and transparency potential.
* Observed microLED parts are not as good as expected on power consumption, possibly because drivers are not optimized for microLEDs, so more sample evidence is needed.
* Cost depends on scaling and production-line investment, while smaller LEDs improve wafer and technology utilization.

📋 **Clip Abstract** The clip compares LCD with edge backlight, LCD with matrix backlight, OLED and microLED for automotive displays. It credits microLED with brightness scaling, robustness, black uniformity and transparency, while flagging power consumption, efficiency evidence, cost and production scaling as remaining weaknesses.

About the speaker:
* Speaker: Kai Hohmann
* Company: Continental Corporation
* Event: MicroLED Connect 2024
* Location: High Tech Campus, Eindhoven, Netherlands

Join the most event MicroLED, AR/VR display and Optical I/O Connect event of the year
Learn more https://www.microledconnect.com/

#EdgeBacklightLCD, #MatrixBacklightLCD, #MicroLEDPowerConsumption, #WaferUtilization, #AutomotiveDisplays, #MicroLEDDisplays

11:15 - 13:36

Where does microLED solve a real automotive display problem, and where is it only a cost battle?

Where does microLED solve a real automotive display problem, and where is it only a cost battle?

In a scenic-view product, today’s LCD uses a matrix backlight, but the application needs high brightness and sunlight robustness. OLA is not bright enough now and cannot fulfill 5,000 canula per square metre. A potential use case is microLED on TFT class. The risk is cost versus the matrix backlight; efficiency may be a benefit, so it is a suitable application to watch.

AR HUD today uses LCD or DLP with high-brightness problems, needing 70,000 can per square metre on the display surface, and it is sunlight exposed. The HUD projects into the driver’s eye, but a path exists from the sun to the mirrors. Smaller displays need higher magnification, worsening sunlight exposure. MicroLED on CMOS must be as large as possible to reduce magnification, or as small as possible to reduce cost, or an intermediate layer is needed.

Direct-view displays are different: microLED competes with LCD, and there is no real problem with incumbent technologies at the moment. OLA is scaled to large sizes, LCDs are scaled up, resolution is achievable, and brightness is not a blocking point. Here microLED faces risk because there is no real problem to solve; it is a cost competition and a cost battle. The next topic is so-called invisible technology.

In this short video, you can learn:
* Scenic-view LCDs with matrix backlights need high brightness and sunlight robustness, while OLA cannot meet 5,000 canula per square metre, leaving microLED on TFT as a cost-risk candidate.
* AR HUD needs 70,000 can per square metre and a smaller display raises magnification and sunlight exposure, so microLED on CMOS size or an intermediate layer becomes a trade-off.
* Direct-view displays show no blocking incumbent problem, so microLED there is a cost competition and cost battle rather than a performance fix.

📋 **Clip Abstract** The clip assesses microLED against LCD, DLP and OLA in scenic-view, AR HUD and direct-view automotive displays. Scenic view and AR HUD expose brightness and sunlight-robustness gaps, while direct view is a cost battle because incumbent technologies already meet the stated needs.

About the speaker:
* Speaker: Kai Hohmann
* Company: Continental Corporation
* Event: MicroLED Connect 2024
* Location: High Tech Campus, Eindhoven, Netherlands

Join the most event MicroLED, AR/VR display and Optical I/O Connect event of the year
Learn more https://www.microledconnect.com/

#MicroLEDOnTFT, #MicroLEDOnCMOS, #MatrixBacklight, #SunlightExposure, #AutomotiveDisplays, #MicroLEDDisplays

More Snippets
CONTACT US

KGH Concepts GmbH

Mergenthalerallee 73-75, 65760, Eschborn

+49 17661704139

admin@techblick.com

TechBlick is owned and operated by KGH Concepts GmbH

Registration number HRB 121362

VAT number: DE 337022439

  • LinkedIn
  • YouTube

Sign up for our newsletter to receive updates on our latest speakers and events AND to receive analyst-written summaries of the key talks and happenings in our events.

Thanks for submitting!

© 2026 by KGH Concepts GmbH

bottom of page