Katharina Gerber | LiCap Technologies: How does a solvent-free, three-step dry electrode process improve solid-state interfaces and cut equipment size?
08:17 - 10:42
Other snippets from this talk
Summary of the clip:
How does a solvent-free, three-step dry electrode process improve solid-state interfaces and cut equipment size?
The process is only three steps: mixing active material, conductive agent and binder; activating the binder; then forming the film. No solvent is added as in a wet slurry line. Instead a proprietary activation step makes the binder fibrillize into a cotton-candy-like structure, so the dry powder can be pressed into a freestanding electrode film and laminated onto the current collector.
Removing NMP and other solvents eliminates the incompatibility between solid-state electrolytes and solvents, which widens the materials window beyond what existing systems allow. Pressing freestanding films also gives much better adhesion, enabling a sandwich-like build: the electrolyte layer can be pressed directly onto an electrode layer, so interfacial contact improves.
Equipment is a commercial lever here. The activated dry electrode line is only one third the size of commonly used industrial equipment, and if it has to sit in a dry room, the smaller footprint saves cost there again. That matters because there are no gigafactories for solid-state batteries yet.
In this short video, you can learn:
* Binder fibrillation replaces solvent-based slurry mixing, turning the dry powder into a cotton-candy-like mass that presses into a freestanding film.
* Skipping NMP removes the solvent-to-solid-electrolyte incompatibility that blocks many candidate materials, while direct electrolyte-on-electrode pressing improves interfacial contact.
* The activated dry electrode line occupies one third of the usual industrial equipment footprint, cutting dry-room cost before any solid-state gigafactory exists.
📋 **Clip Abstract** A three-step, solvent-free route mixes active material, conductive agent and binder, then fibrillizes the binder so the dry powder presses into a freestanding electrode film for lamination. Eliminating NMP widens the compatible solid-state materials set, direct electrolyte pressing improves interfacial contact, and the line needs one third the usual equipment footprint.
About the speaker:
* Speaker: Katharina Gerber
* Company: LiCap Technologies
* Event: Solid-State Batteries: Innovations, Promising Start-ups, Future Roadmap
* Location: Online
Join TechBlick to learn about the state of the art in solid state batteries, Si anode, advanced cathodes, sodium batteries, and beyond
https://www.techblick.com/
#DryElectrodeProcess, #BinderFibrillation, #NMPFreeProcessing, #FreestandingElectrodeFilm, #SolidStateBatteries, #RollToRollManufacturing
This is a highlight of the presentation:
R2R Activated Dry Electrode Process for Cost-Effective Production of Solid-State Batteries
More Highlights from the same talk.
10:55 - 13:18
What CapEx, footprint and energy savings can dry electrode deliver at 10 GWh annual capacity?
What CapEx, footprint and energy savings can dry electrode deliver at 10 GWh annual capacity?
For a 10 GWh annual manufacturing capacity, the analysis quantified CapEx, labor hours, manufacturing footprint and energy consumption. Electrode manufacturing is a huge allocated gray area, and most of it is dedicated to drying solvent and solvent recovery, making it expensive. As a drop-in solution, activated dry electrode shrinks that area substantially, with CapEx falling by more than 50% and footprint about one-third.
The energy effect is central. In current gigafactories, about 47% of entire Gigafactory consumption is allocated to electrode manufacturing. Reducing that need with the dry process lowers battery-manufacturing energy demand and consequently the carbon emissions associated with generating the electricity needed to run the gigafactory. The presentation frames this as a significant consequence for electrode and battery manufacturing.
The carbon benefit matters because renewable energy is not yet fully in the electricity mix. By reducing energy demand, the activated dry electrode route reduces the carbon footprint of battery manufacturing. That is especially important for European manufacturers facing rules and the upcoming battery passport requirement, where the process reduction in energy need connects directly to emissions from the electricity used to run production.
In this short video, you can learn:
* For 10 GWh annual capacity, activated dry electrode is presented as a drop-in solution with CapEx reduced by more than 50% and manufacturing footprint about one-third.
* About 47% of entire gigafactory energy consumption is allocated to electrode manufacturing, much of it for solvent drying and recovery.
* Lower energy demand translates into lower carbon emissions from electricity generation, which is relevant to European rules and the upcoming battery passport.
📋 **Clip Abstract** At 10 GWh annual capacity, the analysis compares conventional electrode manufacturing—dominated by solvent drying and recovery—with an activated dry electrode drop-in route. It reports more than 50% lower CapEx, about one-third the footprint, and significantly lower energy consumption, with electrode manufacturing accounting for about 47% of gigafactory energy use and the reduction linked to lower carbon emissions.
About the speaker:
* Speaker: Katharina Gerber
* Company: LiCap Technologies
* Event: Solid-State Batteries: Innovations, Promising Start-ups, Future Roadmap
* Location: Online
Join TechBlick to learn about the state of the art in solid state batteries, Si anode, advanced cathodes, sodium batteries, and beyond
https://www.techblick.com/
#ActivatedDryElectrode, #SolventDryingRecovery, #ElectrodeManufacturingCapEx, #GigafactoryEnergyUse, #SolidStateBatteries, #BatteryManufacturing
22:49 - 24:32
Why can't non-activated dry binder go below 6%, and what does activation change?
Why can't non-activated dry binder go below 6%, and what does activation change?
Maxwell's dry electrode technology was originally developed for ultracapacitors, where active material content is typically around 80% and up to 15% of the electrode can be binder. That composition is not transferable: no one would buy a battery electrode with only 80% active material. Battery electrodes must cut the binder fraction, which is where the activation question begins.
The stated difference is that Maxwell does not activate the binder. Activation is described as quite critical for battery materials: with non-activated binder the loading cannot be reduced below roughly 6%. Push lower and you run into problems with scalability and with the mechanical strength of the electrode film.
LiCap's answer is an activation method for the electrode, which the presenter says makes it more flexible and scalable. The starting point was knowing the limits of the original Maxwell dry battery electrode, which the company's president invented. So the claim rests on a deliberate departure from the non-activated route rather than an incremental tweak.
In this short video, you can learn:
* Maxwell's dry electrode process came out of ultracapacitors, where electrodes run about 80% active material and up to 15% binder.
* Without binder activation, binder content cannot practically drop below roughly 6% before scalability and electrode film strength suffer.
* An activation step is positioned as making the electrode more flexible and scalable than the non-activated Maxwell route.
📋 **Clip Abstract** Maxwell's dry electrode process was built for ultracapacitors at roughly 80% active material and up to 15% binder, a loading no battery customer would accept. The claimed differentiator is binder activation: without it binder cannot go below about 6% without hurting scalability and electrode film strength, while activation is said to make the film more flexible and scalable.
About the speaker:
* Speaker: Katharina Gerber
* Company: LiCap Technologies
* Event: Solid-State Batteries: Innovations, Promising Start-ups, Future Roadmap
* Location: Online
Join TechBlick to learn about the state of the art in solid state batteries, Si anode, advanced cathodes, sodium batteries, and beyond
https://www.techblick.com/
#DryElectrodeProcessing, #BinderActivation, #ElectrodeFilmStrength, #ActiveMaterialLoading, #SolidStateBatteries, #BatteryManufacturing
18:04 - 19:52
What are the first solid-state targets for NMC811, sulfide electrolyte, active content and loading?
What are the first solid-state targets for NMC811, sulfide electrolyte, active content and loading?
The first solid-state project pairs an NMC811 cathode with a lithium germanium phosphorus sulfide electrolyte supplied by a large sulfide-based solid-state electrolyte manufacturer. Material was shipped the morning of the update, and electrode trials will use existing activated dry electrode manufacturing capacity. Lab-scale equipment, including jet mills and mixers, has been moved into a dry room to handle the materials.
Initial targets are 85% active material content and active loading above 35 mg/cm². The process is not capped at that loading; higher active loadings remain possible with activated dry electrode manufacturing. That matters because wet slurry processing struggles to reach higher loadings, a stated limitation of the incumbent route. The project is about to start.
The rationale is feasibility and benefit evaluation: the conclusion was that trying the solid-state route makes sense. Activated dry electrode technology is positioned as a potential path for these electrodes, with optimism around the upcoming trials. The work combines a sulfide electrolyte partner’s material with dry-room jet milling, mixing and electrode manufacturing capacity.
In this short video, you can learn:
* The first solid-state electrode project targets NMC811 mixed with lithium germanium phosphorus sulfide from a large sulfide-electrolyte manufacturer.
* Targets are 85% active material content and over 35 mg/cm² active loading, with higher loadings possible.
* Wet slurry processing has difficulty reaching higher loadings, a limitation activated dry electrode aims to address.
📋 **Clip Abstract** The first solid-state electrode project will combine NMC811 with a lithium germanium phosphorus sulfide electrolyte supplied by a large manufacturer, using activated dry electrode capacity in a dry room. Initial targets are 85% active material and over 35 mg/cm² loading, with higher loadings possible and wet slurry’s loading limits cited as the contrast.
About the speaker:
* Speaker: Katharina Gerber
* Company: LiCap Technologies
* Event: Solid-State Batteries: Innovations, Promising Start-ups, Future Roadmap
* Location: Online
Join TechBlick to learn about the state of the art in solid state batteries, Si anode, advanced cathodes, sodium batteries, and beyond
https://www.techblick.com/
#ActivatedDryElectrode, #NMC811, #SulfideElectrolyte, #DryRoomProcessing, #SolidStateBatteries, #BatteryManufacturing
About this talk
→ R2R Activated Dry Electrode Process for Cost-Effective Production of Solid-State Batteries · Katharina Gerber · Battery Materials: Next-Gen & Beyond Lithium Ion 2022


