Ken Klapproth | CHASM Advanced Materials: Can CNT hybrid heaters be sprayed onto 3D surfaces, and is there an upper power density limit?
22:46 - 24:43
Other snippets from this talk
Summary of the clip:
Can CNT hybrid heaters be sprayed onto 3D surfaces, and is there an upper power density limit?
The 10 ohm-per-square CNT hybrid is not a single material: it needs the film plus the CNT ink applied over the top. A CNT-only coating can be sprayed, but it cannot reach the heat loading the hybrid achieves. For 3D curves, the stack is built on a film, thermoformed to shape, then overmolded. Spraying the hybrid directly onto a 3D surface is not possible at this time.
On the upper power density limit, none has been established. It depends on the heat load and the surrounding material. The customer who reached 248 degrees Fahrenheit had the heater bonded to a glass structure sitting in an environment that was not dissipating heat. Provided heat is dissipated to keep the heater below the substrate's plastic temperature, a design should be achievable.
The highest figure demonstrated is 3,000 watts per square meter, and even there the constraint is thermal management rather than the heater itself. Because performance is set by how quickly heat leaves the part, the practical ceiling is the plastic temperature of the substrate and the dissipation path around it, not an intrinsic limit of the CNT hybrid coating stack.
In this short video, you can learn:
* The 10 ohm-per-square hybrid needs both the film and the CNT ink overlay; a spray-only CNT coating cannot reach the same heat loading.
* 3D-curved parts are made by coating a film, thermoforming it and overmolding — the hybrid cannot yet be sprayed onto a 3D surface.
* Demonstrated output has reached 3,000 watts per square meter with no ceiling found; substrate plastic temperature and heat dissipation set the real limit.
📋 **Clip Abstract** The 10 ohm-per-square CNT hybrid is built on a film, thermoformed and overmolded for 3D curves, because the hybrid cannot yet be sprayed onto a 3D surface. Power density has reached 3,000 watts per square meter with no upper limit identified; the binding constraints are substrate plastic temperature and heat dissipation.
About the speaker:
* Speaker: Ken Klapproth
* Company: CHASM Advanced Materials
* Event: Printed, Flexible, Hybrid & InMold Electronics 2021
* Location: Online
Join TechBlick - the home of printed electronics, additive electronics, hybrid electronics, sustainable electronics
https://www.techblick.com/
#CNTHybrid, #Thermoforming, #Overmolding, #PowerDensity, #PrintedElectronics, #ConductiveInks
This is a highlight of the presentation:
Why your next automotive heater will be a CNT hybrid
More Highlights from the same talk.
07:14 - 09:35
How do carbon nanotubes encapsulate silver nanowires and provide conductive redundancy in a hybrid film?
How do carbon nanotubes encapsulate silver nanowires and provide conductive redundancy in a hybrid film?
The CNT hybrid overcomes the traditional coupling between variables, the speaker says, because carbon nanotubes are conductive, self-assembling and environmentally neutral. In a scanning electron microscope image, a silver nanowire film is combined with carbon nanotube ink: straight spaghetti-like silver nanowires have finite length and lie on the surface, while carbon nanotubes resemble wet spaghetti encompassing them. A small dosage was used so the interaction remains visible.
Silver nanowires themselves are rigid, and although the deposited surface has some flexibility, any discontinuity or place where nanowire ends do not meet is prone to separation. The carbon nanotubes encapsulate them, bind together over the top and hold them together as they self-assemble into networks. This binding addresses separation at nanowire discontinuities in the hybrid film.
The CNTs also perform conductive redundancy. Anywhere there is open area in the film, which normally would not be conductive, now becomes conductive. If any silver nanowires separate or break, the carbon nanotubes act as a redundant highway, so the electrical path continues. This structural and conductive redundancy is the CNT hybrid's role.
In this short video, you can learn:
* Carbon nanotubes are conductive, self-assembling and environmentally neutral because they are made of carbon, and they intertwine into networks on a surface.
* In the scanning electron microscope image, silver nanowires appear as straight, finite-length, spaghetti-like rods while carbon nanotubes resemble wet spaghetti encompassing them.
* The CNTs encapsulate and bind the silver nanowires, make open film areas conductive and act as a redundant highway if wires separate or break.
📋 **Clip Abstract** The clip explains how a CNT hybrid combines a silver nanowire film with carbon nanotube ink, using a scanning electron microscope image to show nanotubes encompassing straight nanowire rods. It describes how encapsulating CNTs bind nanowires together, make open areas conductive and provide a redundant highway when wires separate or break.
About the speaker:
* Speaker: Ken Klapproth
* Company: CHASM Advanced Materials
* Event: Printed, Flexible, Hybrid & InMold Electronics 2021
* Location: Online
Join TechBlick - the home of printed electronics, additive electronics, hybrid electronics, sustainable electronics
https://www.techblick.com/
#CNTHybrid, #SilverNanowireFilm, #CarbonNanotubeInk, #ConductiveRedundancy, #FlexibleElectronics, #PrintedElectronics
15:14 - 17:12
How did a 14-ohm CNT hybrid heater perform in real-world thermal testing on a truck lens for Arctic and blizzard conditions?
How did a 14-ohm CNT hybrid heater perform in real-world thermal testing on a truck lens for Arctic and blizzard conditions?
For an ice-and-snow-control customer—the kind of trucking seen on Ice Road Truckers—a polycarbonate heater was laminated to the inside of a lens curved in three dimensions. The curvature was gentle enough for lamination. The heater was designed for 14 ohms at 15 V DC and drew just over about one amp.
Within seven minutes, a frontside thermocouple measured a 40°F rise above ambient—about 105°F in total—through the full thickness of the lens. The lens was about 2 or 3 millimeters thick, if recalled correctly. At the same time, the heating film on the inside surface of the lens reached about 145°F.
In about 13 minutes overall, the heater reached steady state at about 115°F outside and about 160°F inside. The customer’s design target was to hit this temperature in less than 15 minutes, and the result came in at under half the time. A thermal image showed extremely even, consistent heat distribution with no hot spots—unlike microwires, where empty space between wires must be overpowered to catch up.
In this short video, you can learn:
* A 14-ohm CNT hybrid heater at 15 V DC drew just over an amp and raised the lens 40°F above ambient within seven minutes.
* The heater reached steady state in about 13 minutes—115°F outside and 160°F inside—against a sub-15-minute design target.
* Thermal imaging showed even, consistent heat without hot spots, avoiding the microwire need to overpower wires so gaps catch up.
📋 **Clip Abstract** A trucking customer needed ice and snow control for Arctic and blizzard conditions on a lens curved in three dimensions. A laminated polycarbonate CNT hybrid heater designed for 14 ohms at 15 V DC met the target in about 13 minutes, with even heat and no hot spots.
About the speaker:
* Speaker: Ken Klapproth
* Company: CHASM Advanced Materials
* Event: Printed, Flexible, Hybrid & InMold Electronics 2021
* Location: Online
Join TechBlick - the home of printed electronics, additive electronics, hybrid electronics, sustainable electronics
https://www.techblick.com/
#CNTHybridHeater, #PolycarbonateLamination, #ThermalImaging, #NoHotSpots, #PrintedElectronics, #FlexibleHybridElectronics
13:13 - 14:59
What is the 3-step patterning process for CNT hybrid films and what sheet resistance options are available?
What is the 3-step patterning process for CNT hybrid films and what sheet resistance options are available?
Patterning starts from a precoated silver nanowire film. A screen printing process then deposits CNT ink down to 100-micron features in any chosen pattern — an antenna, a heater, any shape required. Because the printed CNT ink encapsulates the silver, it becomes the mask itself, so the separate photolithographic mask removal step disappears. The sequence reduces to print, etch, and done: three steps.
A mild etchant removes the unprotected silver nanowires in a couple of seconds, leaving only the CNT-encapsulated regions. The approach leans on pervasive, scalable screen printing practices, so large volumes can be manufactured at scale. Changing the pattern requires no more than creating new screens for the printer, which keeps tooling changes simple and quick.
Three silver-nanowire CNT hybrid versions are available: 75 ohms per square at 98% BLT, 30 ohms per square at 95% BLT, and 10 ohms per square at 90% PLT. Heater customers tend to select either the 30-ohm-per-square or the 10-ohm-per-square grade, and every one of these options can be produced with the same print, etch, and done flow.
In this short video, you can learn:
* CNT ink printed by screen printing acts as its own etch mask, eliminating the separate photolithographic mask removal step.
* The three-step print, etch and done sequence reaches 100-micron features, with pattern changes handled simply by making new screens.
* The grades are 75, 30 and 10 ohms per square at 98%, 95% and 90% BLT or PLT, with heaters typically using the 30 or 10 ohm versions.
📋 **Clip Abstract** CNT hybrid films built on precoated silver nanowire are patterned by screen printing CNT ink into the wanted shape, after which a mild etchant strips unprotected silver in a couple of seconds, the ink itself serving as the mask. Three sheet resistance options — 75, 30 and 10 ohms per square — all run in the same print, etch and done flow.
About the speaker:
* Speaker: Ken Klapproth
* Company: CHASM Advanced Materials
* Event: Printed, Flexible, Hybrid & InMold Electronics 2021
* Location: Online
Join TechBlick - the home of printed electronics, additive electronics, hybrid electronics, sustainable electronics
https://www.techblick.com/
#CNTInk, #SilverNanowire, #ScreenPrinting, #SheetResistance, #PrintedElectronics, #AutomotiveHeaters
About this talk
→ Why your next automotive heater will be a CNT hybrid · Ken Klapproth · Printed, Flexible, Hybrid, & InMold Electronics 2021


