Kenji Mawatari | Konica Minolta: Can a KM24-MHV printhead jet a 50 mPa·s Newtonian fluid within its normal voltage limits?
08:16 - 10:31
Other snippets from this talk
Summary of the clip:
Can a KM24-MHV printhead jet a 50 mPa·s Newtonian fluid within its normal voltage limits?
The KM24-MHV uses an HA-type shared-wall three-cycle piezo actuator. Because neighboring nozzles share the actuator wall, it cannot jet at very high frequency, but it offers good power efficiency. Its driving voltage is lower for the standard 10 mPa·s viscosity.
Using this printhead, they demonstrated a Newtonian fluid with 50 mPa·s viscosity at room temperature. The tested ink is 50 mPa·s at room temperature, and its viscosity reduces gradually as temperature increases. Changing temperature allowed several viscosity ranges to be tested with the same ink and printhead. Its viscosity dependence on shear rate remained very constant, confirming Newtonian behavior.
Jetting results used a drop poacher and waveform optimization: voltage ratio, pulse width and pulse shape. The blue line marks the nominal 10 mPa·s viscosity range; at actual 6 mPa·s, voltage is around nominal. Decreasing temperature to raise viscosity to 30 and 50 mPa·s still allowed jetting within the electronics’ electrical limitation.
In this short video, you can learn:
* The KM24-MHV’s shared-wall three-cycle actuator trades very high frequency for good power efficiency and lower driving voltage at 10 mPa·s.
* The same 50 mPa·s Newtonian ink was tested across viscosity ranges by changing temperature, with constant shear-rate dependence.
* Waveform optimization enabled jetting at 6, 30 and 50 mPa·s within the electronics’ electrical limitation.
📋 **Clip Abstract** The KM24-MHV printhead, using an HA-type shared-wall three-cycle piezo actuator, was demonstrated with a 50 mPa·s Newtonian fluid at room temperature. By varying temperature and optimizing waveform voltage ratio, pulse width and pulse shape, jetting remained within the electronics’ electrical limitation at 6, 30 and 50 mPa·s.
About the speaker:
* Speaker: Kenji Mawatari
* Company: Konica Minolta
* Event: Electronics RESHAPED 2026 | Berlin
* Location: Estrel, Berlin
USA: The Future of Electronics RESHAPED | USA
📅 Save the date: 9 and 10 June 2027
📍 Mountain View, California (Silicon Valley)
📋 Info: https://www.techblick.com/electronicsreshapedusa
Europe
The Future of Electronics RESHAPED | Berlin
📅 Save the date: 20 and 21 October 2027
📍 Berlin, Germany
📋 Info: https://www.techblick.com/electronicsreshaped
#KM24MHVPrinthead, #SharedWallPiezo, #NewtonianFluid, #HighViscosityJetting, #PrintedElectronics, #InkjetPrinting
This is a highlight of the presentation:
High Viscosity Fluid Jetting Technology for industrial applications with Konica Minolta Printheads
More Highlights from the same talk.
02:46 - 03:42
How does the HM printhead survive 50% NMP ink and exceed conventional lifetime by 10×?
How does the HM printhead survive 50% NMP ink and exceed conventional lifetime by 10×?
The HM series is a new printhead coating technology built on the existing KM10NO-i platform. It targets industrial-level solvent jetting, where applications such as perovskite solar panels require aggressive solvents including NMP, DMSO and DMF. The coating is the change that lets the printhead face these fluids rather than conventional solvent exposure.
For a customer ink containing 50% NMP, the HM printhead becomes more durable. Its lifetime is more than 10 times that of the conventional model, according to the comparison presented. That durability matters because aggressive solvents are the enabling condition for industrial applications, and the printhead must survive the ink chemistry.
The session frames high-viscosity fluid jetting as the main topic, with the HM series as the solvent-capable printhead example. The stated applications include perovskite solar panels and other industrial uses needing NMP, DMSO or DMF. The result is a printhead designed around aggressive-solvent inks, not just around conventional fluids.
In this short video, you can learn:
* The HM series is a new coating technology based on the existing KM10NO-i printhead series.
* Industrial applications such as perovskite solar panels require aggressive solvents including NMP, DMSO and DMF.
* With 50% NMP-containing ink, the new printhead is more than 10 times more durable in lifetime than the conventional model.
📋 **Clip Abstract** The HM series is a new printhead coating built on KM10NO-i for industrial solvent jetting. It is shown to make a 50% NMP-containing ink more durable, with more than 10 times the lifetime of the conventional model.
About the speaker:
* Speaker: Kenji Mawatari
* Company: Konica Minolta
* Event: Electronics RESHAPED 2026 | Berlin
* Location: Estrel, Berlin
USA: The Future of Electronics RESHAPED | USA
📅 Save the date: 9 and 10 June 2027
📍 Mountain View, California (Silicon Valley)
📋 Info: https://www.techblick.com/electronicsreshapedusa
Europe
The Future of Electronics RESHAPED | Berlin
📅 Save the date: 20 and 21 October 2027
📍 Berlin, Germany
📋 Info: https://www.techblick.com/electronicsreshaped
#HMPrinthead, #NMPInk, #PerovskiteSolar, #PrintheadLifetime, #HighViscosityJetting, #IndustrialInkjet
14:05 - 15:33
How can resonant multi-pulse waveforms stably jet a non-Newtonian ink with 200 mPa·s static viscosity?
How can resonant multi-pulse waveforms stably jet a non-Newtonian ink with 200 mPa·s static viscosity?
The test fluid was non-Newtonian, with static viscosity of 30 mPa·s and even 200 mPa·s. A different printhead type applied many pulses at a resonant frequency. Those pulses impose a higher shear rate on the ink inside the nozzle. For non-Newtonian ink, that shear is described as very effective at reducing the actual viscosity.
With the first ink, jetting occurred before optimization, but the meniscus was not stable. After several seconds, the result was abnormal jetting. Optimizing the waveform changed that: under the optimized condition, the ink jetted very stably. This sequence links waveform optimization directly to meniscus stability over time.
The optimized condition enabled a more difficult ink: 200 mPa·s at room temperature, which decreases significantly at higher shear rate. That is the same shear-rate dependence the resonant multi-pulse approach exploits in the nozzle. This establishes the mechanism: many resonant pulses raise shear and lower actual viscosity for the high-static-viscosity non-Newtonian fluid.
In this short video, you can learn:
* The test used non-Newtonian fluid with 30 mPa·s and even 200 mPa·s static viscosity.
* A printhead applied many pulses at resonant frequency, giving higher shear rate to ink in the nozzle and reducing actual viscosity.
* Waveform optimization produced stable jetting after initial meniscus instability and abnormal jetting, then a 200 mPa·s room-temperature ink was challenged.
📋 **Clip Abstract** The test used a non-Newtonian fluid with 30 mPa·s and even 200 mPa·s static viscosity, jetted by a printhead applying many pulses at resonant frequency. After waveform optimization stabilized the meniscus and jetting, a more difficult 200 mPa·s room-temperature ink was challenged because its viscosity decreases significantly at higher shear rate.
About the speaker:
* Speaker: Kenji Mawatari
* Company: Konica Minolta
* Event: Electronics RESHAPED 2026 | Berlin
* Location: Estrel, Berlin
USA: The Future of Electronics RESHAPED | USA
📅 Save the date: 9 and 10 June 2027
📍 Mountain View, California (Silicon Valley)
📋 Info: https://www.techblick.com/electronicsreshapedusa
Europe
The Future of Electronics RESHAPED | Berlin
📅 Save the date: 20 and 21 October 2027
📍 Berlin, Germany
📋 Info: https://www.techblick.com/electronicsreshaped
#NonNewtonianInk, #ResonantPulseWaveform, #HighViscosityJetting, #MeniscusStability, #InkjetPrinting, #PrintedElectronics
11:01 - 13:15
Why does high-viscosity jetting destabilize above 10 kHz, and how does a 3.7 pL printhead help?
Why does high-viscosity jetting destabilize above 10 kHz, and how does a 3.7 pL printhead help?
At high frequency, the next droplet velocity becomes much higher than the first because of refilling behavior. Higher-viscosity fluid causes bigger pressure loss in the channel, so the meniscus cannot recover to its initial position and the next droplet is affected. To reduce this refilling influence, a smaller-droplet printhead was chosen.
Several commercially sold droplet volumes were simulated, and 3.7 pL is the smallest in the lineup. Using this printhead, high frequency was demonstrated with higher viscosity. The same fluid was used for testing, and good droplet formation was shown at 10, 30 and 50 mPa·s.
Droplet velocity was measured from the first to the tenth droplet at various jetting periods, equal to frequency. A 50 µs period equals 20 kHz; 100 µs equals 10 kHz. At 20 kHz the second droplet velocity becomes much higher and increases constantly; up to 10 kHz or less it is relatively constant.
In this short video, you can learn:
* At 20 kHz, the second droplet velocity is much higher than the first and increases constantly.
* At 10 kHz or less, velocity from the first to tenth droplet is relatively constant.
* The 3.7 pL printhead showed good droplet formation at 10, 30 and 50 mPa·s while demonstrating higher-viscosity jetting.
📋 **Clip Abstract** Higher-viscosity fluid creates greater channel pressure loss, preventing meniscus recovery and destabilizing subsequent droplets at high frequency. Using the smallest 3.7 pL printhead, testing with 10, 30 and 50 mPa·s fluids showed good droplet formation and relatively constant velocity up to 10 kHz, while 20 kHz produced a much higher second-droplet velocity that kept increasing.
About the speaker:
* Speaker: Kenji Mawatari
* Company: Konica Minolta
* Event: Electronics RESHAPED 2026 | Berlin
* Location: Estrel, Berlin
USA: The Future of Electronics RESHAPED | USA
📅 Save the date: 9 and 10 June 2027
📍 Mountain View, California (Silicon Valley)
📋 Info: https://www.techblick.com/electronicsreshapedusa
Europe
The Future of Electronics RESHAPED | Berlin
📅 Save the date: 20 and 21 October 2027
📍 Berlin, Germany
📋 Info: https://www.techblick.com/electronicsreshaped
#HighViscosityJetting, #PicoliterPrinthead, #DropletVelocity, #MeniscusRefilling, #InkjetPrinting, #PrintedElectronics
About this talk
→ High Viscosity Fluid Jetting Technology for industrial applications with Konica Minolta Printheads · Kenji Mawatari · The Future of Electronics RESHAPED 2026 Berlin


