top of page

Kimmo Pernu, Terho Lahtinen

Movesense by Suunto Oy

* All members of the platform can watch the entire presentation.

 

Please register to become a member.

Kimmo Pernu, Terho Lahtinen | Movesense by Suunto Oy: What wash, flex and heat-press specifications must an in-mold connector survive to be sewn into apparel?

13:41 - 15:33

Other snippets from this talk

Summary of the clip:

What wash, flex and heat-press specifications must an in-mold connector survive to be sewn into apparel?

The qualification target is swimming and washing-machine proof, tested by 50 machine washing cycles. Operating temperature follows standard product ranges, from freezing cold to hot environments, using an internal cycling protocol. Mechanical stress is also specified: flexing at 90 degrees for 5,000 cycles at room temperature and 1,000 cycles in freezing temperatures, with twisting tested for the same cycle counts.

A thermal bonding shock is verified with regular heat-press machines. Before that, production moves through cutting the parts from the foil, assembling the snap connectors, and final quality checking with quality-control tests. These steps show the connector as a foil-based part that must survive both environmental cycling and the mechanical and thermal loads imposed during apparel integration.

The Smart Fabric Connector is bonded to fabrics and apparel by sandwiching it between a fabric stack, with hot-melt adhesive on both sides. Bonding can use a regular t-shirt press, a flat press, or mold cavity presses. That heat-press route is the integration point where wash, flex, temperature and thermal-bonding-shock requirements meet the actual apparel construction.

In this short video, you can learn:
* 50 machine washing cycles is the test spec for swimming and washing-machine proofing.
* Flexing is tested at 90 degrees for 5,000 room-temperature cycles and 1,000 freezing-temperature cycles, with twisting at the same counts.
* Thermal bonding shock is verified with regular heat-press machines, and the connector is sandwiched in a fabric stack with hot-melt adhesive on both sides.

📋 **Clip Abstract** The clip sets out test criteria for a Smart Fabric Connector: 50 machine washing cycles, standard product operating-temperature cycling, 90-degree flexing for 5,000 room-temperature and 1,000 freezing-temperature cycles, matching twist cycles, and thermal bonding shock with regular heat-press machines. It then shows bonding by sandwiching the connector between a fabric stack with hot-melt adhesive on both sides, using a flat t-shirt press or mold cavity presses.

About the speakers:
* Speakers: Kimmo Pernu, Terho Lahtinen
* Company: Movesense by Suunto Oy
* Event: Printed, Flexible, Hybrid & InMold Electronics 2021
* Location: Online

Join TechBlick - the home of printed electronics, additive electronics, hybrid electronics, sustainable electronics
https://www.techblick.com/

#MachineWashingCycles, #ThermalBondingShock, #HotMeltAdhesive, #MoldCavityPress, #InMoldElectronics, #WearableElectronics

This is a highlight of the presentation:

In-mold Electronics Add Context Awareness to Smart Apparel

Printed, Flexible, Hybrid & InMold Electronics 2021

​

10-11 March 2021

Online

Organised By:

TechBlick

​

More Highlights from the same talk.

06:19 - 07:50

How can a fabric connector tell a Movesense sensor which connection ID, and which body location, it is attached to?

How can a fabric connector tell a Movesense sensor which connection ID, and which body location, it is attached to?

The starting point was customer demand: apparel makers needed the sensor attached in the garment, and they further needed the sensor to recognize where it had been attached. Earlier attachment routes covered surface mounts and similar approaches; this project went further. The answer was a fabric connector made with in-mold electronics, built specifically to bring context information to the sensor.

The Smart Fabric Connector is made with injection molded electronics technology. The target set for it was an apparel connection interface for Movesense sensors that automatically detects the connection ID of the point where it is actually connected. Detection is automatic by design, so the connection point itself identifies which attachment position the sensor has been placed in.

Knowing that ID from the connection point is where this excerpt ends, and it fixes the division of labour: the connector carries the context, the sensor consumes it. Location is information held on the garment side of the interface and handed over at the connection point, rather than something the sensing device must already contain.

In this short video, you can learn:
* Apparel customers needed the sensor attached in the garment and, additionally, needed the sensor to recognize where it was attached.
* A fabric connector made with in-mold electronics was chosen to bring that context information to the sensor.
* The Smart Fabric Connector target is an apparel connection interface for Movesense sensors that automatically detects the connection ID of the point it is connected to.

📋 **Clip Abstract** An apparel connector built with in-mold electronics is used to give a Movesense motion sensor context about where in the garment it has been attached. The injection molded Smart Fabric Connector automatically detects the connection ID of the point it is plugged into, so connection identity travels from garment to sensor.

About the speakers:
* Speakers: Kimmo Pernu, Terho Lahtinen
* Company: Movesense by Suunto Oy
* Event: Printed, Flexible, Hybrid & InMold Electronics 2021
* Location: Online

Join TechBlick - the home of printed electronics, additive electronics, hybrid electronics, sustainable electronics
https://www.techblick.com/

#InMoldElectronics, #SmartFabricConnector, #InjectionMoldedElectronics, #ConnectionIDDetection, #WearableSensorIntegration, #SmartTextiles

17:40 - 19:08

Why did even simple electronic circuitry struggle with dynamic loading and thermal-and-pressure post-processing shock?

Why did even simple electronic circuitry struggle with dynamic loading and thermal-and-pressure post-processing shock?

The first IME pilot deliberately chose a humble start: simple electronic circuitry, selected to make the project right and succeed while capturing the benefits of a novel technology. The learning was that IME may not be suitable for the most complex electronics at today’s status. The pilot concluded IME is developing toward that direction, and simple electronics remain the safer design target.

Simple electronics probably guarantee a design that realizes and a good yield, yet the pilot still faced many challenges from its dynamic-loading requirements and the post-processing requirement of thermal and pressure shock. Those two constraints mattered even with a humble circuit. The project had to address them as central concerns because they surfaced despite the intentionally limited electronic complexity.

The partner relationship produced a valuable feedback loop: the partner looped back a lot of feedback on how to improve the design over the project. The team called this exchange fruitful learning. That made the pilot valuable beyond the simple circuit itself, because the feedback linked design improvement directly to the challenges of dynamic loading and thermal and pressure post-processing shock.

In this short video, you can learn:
* A humble simple-circuit IME pilot can achieve design realization and yield, but IME was judged unsuitable for the most complex electronics at today’s status.
* Dynamic-loading requirements and thermal-and-pressure post-processing shock created many challenges even for simple electronic circuitry.
* Partner feedback looped back design improvements, making the pilot a fruitful learning exercise beyond circuit simplicity.

📋 **Clip Abstract** An IME pilot chose simple electronic circuitry to secure design realization and yield, then found that dynamic loading and thermal-and-pressure post-processing shock created many challenges anyway. The project concluded that IME is not yet suited to the most complex electronics at today’s status, and that partner feedback on design improvement was a fruitful learning outcome.

About the speakers:
* Speakers: Kimmo Pernu, Terho Lahtinen
* Company: Movesense by Suunto Oy
* Event: Printed, Flexible, Hybrid & InMold Electronics 2021
* Location: Online

Join TechBlick - the home of printed electronics, additive electronics, hybrid electronics, sustainable electronics
https://www.techblick.com/

#SimpleCircuitPilot, #DynamicLoading, #ThermalPressureShock, #DesignFeedbackLoop, #PrintedElectronics, #FlexibleHybridElectronics

11:59 - 13:42

How do silver screen-print passes, vacuum pre-forming, conductive-adhesive mounting and TPU overmolding form a complete IME chain?

How do silver screen-print passes, vacuum pre-forming, conductive-adhesive mounting and TPU overmolding form a complete IME chain?

Production begins with circuitry silkscreen-printed on PET foil across many passes: primers, different-grade silver and carbon inks, plus dielectric inks that protect the silver. After printing, vacuum forming pre-forms the foil, creating a support frame around the electronics components. This sequence turns a flat printed sheet into a shaped substrate ready for component mounting, while the ink stack and protective dielectric remain integral to the PET foil construction.

The printed and formed foil sheet is then placed on a mounting device or surface-mounting equipment, where two components are placed using conductive adhesives. At the end of electronics assembly, PCBA testing verifies that everything went as it should. This stage links the printed circuitry to the active electronics, checking the assembled board before the foil and components move into encapsulation.

For overmolding, the printed and assembled PCBs are put into a mold cavity, and elastomer TPU is overmolded around the electronics. This forms very good encapsulation against environmental stress and mechanical stress for the product. After overmolding, the parts are cut out from the foil and assembly continues. The TPU therefore protects the printed circuitry and mounted components through the subsequent cutting and assembly steps.

In this short video, you can learn:
* Silver and carbon inks are silkscreen-printed on PET foil with primers and dielectric protection across multiple passes.
* Vacuum forming pre-forms the foil to create a support frame around electronics components before mounting.
* Elastomer TPU overmolding encapsulates the assembled electronics against environmental and mechanical stress.

📋 **Clip Abstract** The IME chain starts with multi-pass silkscreen printing of silver and carbon circuitry on PET foil, including primers and dielectric protection, followed by vacuum pre-forming to create a support frame. Components are then mounted with conductive adhesives, PCBA-tested, overmolded in elastomer TPU for environmental and mechanical encapsulation, and finally cut from the foil for assembly.

About the speakers:
* Speakers: Kimmo Pernu, Terho Lahtinen
* Company: Movesense by Suunto Oy
* Event: Printed, Flexible, Hybrid & InMold Electronics 2021
* Location: Online

Join TechBlick - the home of printed electronics, additive electronics, hybrid electronics, sustainable electronics
https://www.techblick.com/

#SilverCarbonInks, #PetFoilPreforming, #ConductiveAdhesiveMounting, #TPUOvermolding, #InMoldElectronics, #PrintedElectronics

Links to this speaker's talk page and other highlights appear here.

More Snippets
CONTACT US

KGH Concepts GmbH

Mergenthalerallee 73-75, 65760, Eschborn

+49 17661704139

admin@techblick.com

TechBlick is owned and operated by KGH Concepts GmbH

Registration number HRB 121362

VAT number: DE 337022439

  • LinkedIn
  • YouTube

Sign up for our newsletter to receive updates on our latest speakers and events AND to receive analyst-written summaries of the key talks and happenings in our events.

Thanks for submitting!

© 2026 by KGH Concepts GmbH

bottom of page