top of page

Lukas Werft

Fraunhofer IZM

* All members of the platform can watch the entire presentation.

 

Please register to become a member.

Lukas Werft | Fraunhofer IZM: Why must a screen-printing ink shear-thin under the squeegee yet not keep flowing for ten minutes?

10:26 - 12:23

Other snippets from this talk

Summary of the clip:

Why must a screen-printing ink shear-thin under the squeegee yet not keep flowing for ten minutes?

Rheology here means shear-dependent viscosity. A Newtonian fluid has constant viscosity across shear rate, while screen printing wants shear-thinning behavior. At the high shear rate under the squeegee, viscosity drops, helping material enter the mesh. In the mesh, it first appears thicker with holes until the flowing part of screen printing builds the print.

When the squeegee passes over the screen, the material thins again and releases onto the substrate. That is good behavior, but time-dependent properties also matter. The material should thin, yet not remain thinner for the next ten minutes. If it does, it floats over the substrate. The physics behind the behavior must be understood to manipulate it.

The screen-printing ink therefore has to balance shear-dependent viscosity with time-dependent properties. High shear lowers viscosity for entering the mesh, but after the squeegee the ink must stop being thin instead of continuing to flow over the substrate. The problem is physical: identify the mechanism behind the behavior and manipulate it. That is the core rheology-control question for the formulation.

In this short video, you can learn:
* A Newtonian fluid has constant viscosity over shear rate, whereas screen printing requires shear-thinning behavior.
* High shear lowers the ink viscosity so it can enter the mesh, and the squeegee thins it again to release onto the substrate.
* Time-dependent properties matter because an ink that stays thinner for ten minutes can float over the substrate, so the underlying physics must be understood and manipulated.

πŸ“‹ **Clip Abstract** The clip explains shear-dependent viscosity in screen-printing inks: a Newtonian fluid is constant, but the process wants shear-thinning so high shear lowers viscosity for mesh entry and squeegee passage releases material onto the substrate. It stresses time-dependent properties, because an ink should not remain thinner for ten minutes and float over the substrate; the physics behind the behavior must be understood to manipulate it.

About the speaker:
* Speaker: Lukas Werft
* Company: Fraunhofer IZM
* Event: Electronics RESHAPED 2026 | Berlin
* Location: Estrel, Berlin

USA: The Future of Electronics RESHAPED | USA
πŸ“… Save the date: 9 and 10 June 2027
πŸ“ Mountain View, California (Silicon Valley)
πŸ“‹ Info: https://www.techblick.com/electronicsreshapedusa

Europe
The Future of Electronics RESHAPED | Berlin
πŸ“… Save the date: 20 and 21 October 2027
πŸ“ Berlin, Germany
πŸ“‹ Info: https://www.techblick.com/electronicsreshaped

#ScreenPrintingRheology, #ShearThinningInks, #SqueegeeShearRate, #TimeDependentFlow, #PrintedElectronics, #StretchableElectronics

This is a highlight of the presentation:

Liquid Metal Inks for Highly Reliable Printed Stretchable Electronics: Formulation, Rheology, and Wetting Control

​

21 and 22 OCT 2026

Estrel, Berlin

Organised By:

TechBlick

​

More Highlights from the same talk.

02:01 - 03:29

Why do copper meanders and silver-particle inks fail under repeated strain, while remaining useful for one-time deformation?

Why do copper meanders and silver-particle inks fail under repeated strain, while remaining useful for one-time deformation?

Copper structures can be patterned as meanders and used as bending structures rather than truly stretchable conductors. The resulting conductive track is stretchable, but it is framed as more useful for one-time deformation. It can be deformed up to 300% elongation without a tangent resistance, according to the presented result.

Under multiple deformation, fracture occurs after a really small amount: maybe 100 or 1,000 cycles, but only 10% elongation. Copper inks or silver inks are described as the most material used at the moment for stretchable electronics. Many process parameters are available for these inks.

Really tiny particles are said to give a good stretchable material, but the provided clip stops before explaining the particle-size mechanism further. The remaining emphasis stays on copper inks, silver inks, and the many process parameters available for stretchable electronics.

In this short video, you can learn:
* Copper meanders behave as bending structures and are more suited to one-time deformation than repeated stretching.
* The copper track can reach 300% elongation without a tangent resistance, but repeated deformation fractures at maybe 100 or 1,000 cycles and only 10% elongation.
* Copper inks or silver inks are the most material used at the moment for stretchable electronics, and really tiny particles are said to give good stretchability.

πŸ“‹ **Clip Abstract** Copper meanders form conductive tracks that can be deformed up to 300% elongation without a tangent resistance, but they are framed as best for one-time deformation. Repeated deformation fractures after maybe 100 or 1,000 cycles at only 10% elongation, while copper inks or silver inks remain the most material used at the moment, with tiny particles giving good stretchability.

About the speaker:
* Speaker: Lukas Werft
* Company: Fraunhofer IZM
* Event: Electronics RESHAPED 2026 | Berlin
* Location: Estrel, Berlin

USA: The Future of Electronics RESHAPED | USA
πŸ“… Save the date: 9 and 10 June 2027
πŸ“ Mountain View, California (Silicon Valley)
πŸ“‹ Info: https://www.techblick.com/electronicsreshapedusa

Europe
The Future of Electronics RESHAPED | Berlin
πŸ“… Save the date: 20 and 21 October 2027
πŸ“ Berlin, Germany
πŸ“‹ Info: https://www.techblick.com/electronicsreshaped

#CopperMeanders, #SilverInks, #StretchableConductiveTracks, #FractureStrainCycling, #PrintedElectronics, #StretchableElectronics

27:44 - 30:08

What contact angle do you need, and what track widths can you actually dispense from liquid metal ink?

What contact angle do you need, and what track widths can you actually dispense from liquid metal ink?

Wetting is framed as a three-part balance between liquid, hard surface and surrounding air; these parts are dependent. For liquid metal ink, a contact angle beneath 45 degrees is described as the best wetting process in most cases. That condition gives a cross-section with enough area for conductive material without flowing everywhere.

The liquid metal ink contains the liquid metal and a polymer-solvent part. The formulation is described as wetting the substrate so well that it reaches the good contact-angle area and gives a structure needed for conductivity. After printing with solvent, the solvent must be removed; sintering can follow and is not really different from the silver case.

Dispensing results show that parameters can be manipulated to produce structures from 100 up to 800 microns wide. Height values are discussed starting at 25 microns. The clip presents these as dispensing samples, linking wetting control and printed geometry to the conductivity requirement at the end of the material.

In this short video, you can learn:
* A contact angle beneath 45 degrees is described as the best wetting process in most cases for this liquid metal ink on a substrate.
* The ink combines liquid metal with a polymer-solvent part; after printing, solvent removal is required and sintering can follow as in the silver case.
* Dispensing samples were manipulated from 100 to 800 microns wide, with height values discussed starting at 25 microns.

πŸ“‹ **Clip Abstract** The clip explains liquid metal ink wetting through a three-part liquid-surface-air balance, with contact angles beneath 45 degrees called the best case. It then covers solvent removal, optional sintering, and dispensing samples manipulated from 100 to 800 microns wide with heights discussed from 25 microns.

About the speaker:
* Speaker: Lukas Werft
* Company: Fraunhofer IZM
* Event: Electronics RESHAPED 2026 | Berlin
* Location: Estrel, Berlin

USA: The Future of Electronics RESHAPED | USA
πŸ“… Save the date: 9 and 10 June 2027
πŸ“ Mountain View, California (Silicon Valley)
πŸ“‹ Info: https://www.techblick.com/electronicsreshapedusa

Europe
The Future of Electronics RESHAPED | Berlin
πŸ“… Save the date: 20 and 21 October 2027
πŸ“ Berlin, Germany
πŸ“‹ Info: https://www.techblick.com/electronicsreshaped

#LiquidMetalInk, #ContactAngleWetting, #SolventRemoval, #DispensingGeometry, #PrintedElectronics, #AdditiveElectronics

15:11 - 17:20

How does a 5-nanometre oxide skin turn an unwettable liquid metal into a printable, copper-wetting paste?

How does a 5-nanometre oxide skin turn an unwettable liquid metal into a printable, copper-wetting paste?

The oxide layer on the liquid metal surface builds in milliseconds and passivates to a thickness of about five nanometres. Often introduced as the material's least attractive property, that skin is stable whenever the metal is at rest β€” which is exactly why structuring processes behave well: the liquid metal never touches the polymer or the contact parts directly.

Electrical contact is made through copper or other metals embedded in the polymer. On its own, the liquid metal would not wet the copper. The thin oxide film changes that: it acts as a bridge between the two surfaces, an interlayer best described as liquid–solid–solid, sitting between the bulk metal and the pad.

That oxide is mostly gallium two, oxygen three β€” Ga2O3 β€” and it wets copper and the polymer surface well. Because the skin governs wetting, the material's properties can be tuned: the oxide becomes the handle for getting more adherent, more reliable contact rather than a defect to be stripped away.

In this short video, you can learn:
* The native oxide grows in milliseconds and passivates at up to five nanometres, remaining stable while the metal is not in movement.
* Because the oxide bridges liquid metal to metal pads embedded in polymer, the metal wets copper it would otherwise refuse.
* The oxide is predominantly Ga2O3, and its wetting behaviour is the lever for tuning adhesion to copper and to polymer.

πŸ“‹ **Clip Abstract** A native oxide a few nanometres thick, formed within milliseconds, is what makes liquid metal printable and reliable rather than merely reactive. Acting as a liquid–solid–solid bridge, the gallium oxide skin lets the metal wet copper pads and polymer surfaces it would otherwise reject.

About the speaker:
* Speaker: Lukas Werft
* Company: Fraunhofer IZM
* Event: Electronics RESHAPED 2026 | Berlin
* Location: Estrel, Berlin

USA: The Future of Electronics RESHAPED | USA
πŸ“… Save the date: 9 and 10 June 2027
πŸ“ Mountain View, California (Silicon Valley)
πŸ“‹ Info: https://www.techblick.com/electronicsreshapedusa

Europe
The Future of Electronics RESHAPED | Berlin
πŸ“… Save the date: 20 and 21 October 2027
πŸ“ Berlin, Germany
πŸ“‹ Info: https://www.techblick.com/electronicsreshaped

#LiquidMetalInk, #GalliumOxideSkin, #WettingControl, #StretchableCircuits, #PrintedElectronics, #AdditiveElectronics

Links to this speaker's talk page and other highlights appear here.

More Snippets
CONTACT US

KGH Concepts GmbH

Mergenthalerallee 73-75, 65760, Eschborn

+49 17661704139

admin@techblick.com

TechBlick is owned and operated by KGH Concepts GmbH

Registration number HRB 121362

VAT number: DE 337022439

  • LinkedIn
  • YouTube

Sign up for our newsletter to receive updates on our latest speakers and events AND to receive analyst-written summaries of the key talks and happenings in our events.

Thanks for submitting!

© 2026 by KGH Concepts GmbH

bottom of page