Marian Breitenbuecher | HighLine Technology Gmbh: What cell efficiency gain must perovskite deliver to beat TopCon even with 90% lower material costs?
00:34 - 01:27
Other snippets from this talk
Summary of the clip:
What cell efficiency gain must perovskite deliver to beat TopCon even with 90% lower material costs?
Efficiencies are not the problem anymore; other tasks have to be solved. A Fraunhofer Institute analysis compares conventional TopCon cells with the 2025 state of perovskite technology. Even assuming a 90% decrease in material costs and a standard degradation in lifetime, a 2% efficiency cell benefit is still required to make perovskite competitive with conventional TopCon, especially for utility-scale applications.
The speaker notes there are nice niches for perovskite already, referencing what was presented in the morning session. But competitiveness against TopCon remains an issue. Material cost is another concern: the analysis shows that even a 90% reduction in material costs is not sufficient on its own when the lifetime degradation assumption is standard.
The required 2% efficiency cell benefit is the condition for utility-scale applications. The point is that perovskite efficiencies are no longer the problem; the remaining tasks are lifetime degradation and the material-cost position relative to conventional TopCon. The Fraunhofer analysis assumes both a 90% material-cost decrease and standard degradation, and still finds that 2% gap.
In this short video, you can learn:
* Perovskite efficiencies are no longer the bottleneck; other tasks remain unsolved.
* Even with a 90% material-cost decrease and standard degradation, perovskite needs a 2% efficiency cell benefit to compete with TopCon at utility scale.
* Nice niches for perovskite already exist, but material cost and lifetime remain open issues.
📋 **Clip Abstract** A Fraunhofer Institute analysis comparing conventional TopCon cells with the 2025 state of perovskite technology sets the competitive bar. Even assuming a 90% decrease in material costs and standard lifetime degradation, perovskite still needs a 2% efficiency cell benefit for utility-scale competitiveness, while niches already exist.
About the speaker:
* Speaker: Marian Breitenbuecher
* Company: HighLine Technology Gmbh
* Event: Perovskite Connect 2026 | Berlin
* Location: Estrel, Berlin
Save the date: Perovskite Connect 2027 | 20 and 21 OCT 2027 | Berlin
Co-located with the Future of Electronics RESHAPED conference and exhibition
Learn more: https://www.techblick.com/perovskiteconnect
Intestered in exhibiting: learn more here: https://www.techblick.com/perovskiteconnect
#PerovskiteTopCon, #EfficiencyCellBenefit, #MaterialCostReduction, #LifetimeDegradation, #PerovskiteSolarCells, #UtilityScalePV
This is a highlight of the presentation:
Enabling Contactless Metallization for Perovskite Devices through Flexible and scalable Dispensing
21 and 22 OCT 2026
Estrel, Berlin
Organised By:
More Highlights from the same talk.
01:43 - 03:09
Does screen-printing metallization mechanically damage the fragile textured pyramids in two-terminal perovskite technology?
Does screen-printing metallization mechanically damage the fragile textured pyramids in two-terminal perovskite technology?
The first two-terminal perovskite technologies started with very planar layers, then moved to buried layers, but the highest efficiency potential sits with fully textured materials. These devices carry nanometer-scale layer thicknesses applied on top of the solar cell, making the substrate very, very fragile. That fragility is the trade-off for the efficiency potential of the fully textured route.
A Helmholtz-Zentrum Berlin investigation indicated that downstream processes may cause harm to these very fragile structures, specifically the screen-printing process used for metallization. In that printing step, mechanical pressure is applied to the pyramids. The discussion asks whether the knot of the screen or the particles pushed through the openings actually harm these pyramids; either way, mechanical stress is caused.
The tension is clear: fully textured two-terminal perovskite technology offers one of the highest efficiencies, yet its nanometer-scale layers and pyramids are vulnerable to mechanical stress. Screen-printing metallization introduces pressure through the screen and through particles, so the damage risk under discussion is mechanical. The open question is which part of the printing process actually harms the pyramids.
In this short video, you can learn:
* Fully textured two-terminal perovskite technology has the highest efficiency potential but uses nanometer-scale layers on a very fragile substrate.
* A Helmholtz-Zentrum Berlin investigation indicated screen-printing metallization may harm these fragile structures.
* The mechanical pressure debate centres on the screen knot versus particles pushed through openings onto the pyramids.
📋 **Clip Abstract** Fully textured two-terminal perovskite technology offers the highest efficiency potential, but its nanometer-scale layers sit on a very fragile substrate. A Helmholtz-Zentrum Berlin investigation points to screen-printing metallization as a downstream mechanical-stress risk, with the screen knot and particles through openings both under discussion.
About the speaker:
* Speaker: Marian Breitenbuecher
* Company: HighLine Technology Gmbh
* Event: Perovskite Connect 2026 | Berlin
* Location: Estrel, Berlin
Save the date: Perovskite Connect 2027 | 20 and 21 OCT 2027 | Berlin
Co-located with the Future of Electronics RESHAPED conference and exhibition
Learn more: https://www.techblick.com/perovskiteconnect
Intestered in exhibiting: learn more here: https://www.techblick.com/perovskiteconnect
#FullyTexturedPerovskite, #ScreenPrintingMetallization, #PerovskitePyramids, #MechanicalStress, #PerovskiteSolarCells, #TwoTerminalPerovskite
15:41 - 16:36
Which material properties matter most when switching screen-printing paste to high-viscosity dispensing?
Which material properties matter most when switching screen-printing paste to high-viscosity dispensing?
The recommendation starts with particles, not rheology. Screen printing adopted flakes in past years, but we do not like flakes at all for this approach. We need closer particle-size control than screen printing provides, plus very good control of agglomeration in the material. Rheology may look similar, but particle control is the basic requirement.
Particle size is the first differentiator. The material must give tighter particle-size control than a screen-printing paste, and agglomeration between particles must be held under very good control. Those are described as the basics. From a rheology point of view, the material used is quite similar; the difference is in how the particles and their interactions are managed.
Particle shape also matters. The recommendation is to control particle size, particle shape and agglomeration between the particles. Those three points are put forward as the key material properties. The rheology requirement is close to the screen-printing material, so the material-development effort should focus on the particle system rather than treating rheology as the main difference.
In this short video, you can learn:
* Screen-printing pastes have relied on flakes, but flakes are not wanted for this high-viscosity dispensing route.
* The material needs tighter particle-size control than screen printing and very good agglomeration control.
* Rheology is similar to the screen-printing material, while particle size, shape and agglomeration are the critical differences.
📋 **Clip Abstract** The clip asks what makes a good material when moving from screen-printing paste to high-viscosity dispensing. The answer is particle control: avoid flakes, tighten particle size beyond screen printing, and keep agglomeration between particles under very good control, while rheology remains similar.
About the speaker:
* Speaker: Marian Breitenbuecher
* Company: HighLine Technology Gmbh
* Event: Perovskite Connect 2026 | Berlin
* Location: Estrel, Berlin
Save the date: Perovskite Connect 2027 | 20 and 21 OCT 2027 | Berlin
Co-located with the Future of Electronics RESHAPED conference and exhibition
Learn more: https://www.techblick.com/perovskiteconnect
Intestered in exhibiting: learn more here: https://www.techblick.com/perovskiteconnect
#ParticleSizeControl, #AgglomerationControl, #ParticleShapeControl, #ScreenPrintingPaste, #PerovskiteDevices, #PrintedElectronics
05:24 - 06:33
How fine and fast can contactless dispensing print solar-cell fingers?
How fine and fast can contactless dispensing print solar-cell fingers?
Current finger width sits in a comfortable 30-micron range, set by an interaction between nozzle design and the supplied material. Those materials are mainly developed for screen printing, still the market’s main player, and carry viscosities around 1,000 pascal seconds with very high metal loading. That combination defines what a contactless dispensing nozzle must handle.
Finer dispensing has been demonstrated with nozzles down to eight microns, producing fingers down to 12 microns. That result matters because it pushes beyond the current 30-micron comfort zone while still confronting screen-printing-oriented materials with around 1,000 pascal seconds viscosity and high metal loading. The nozzle-material pairing, not the nozzle alone, determines how far the feature size can move.
Throughput comes from parallelization: parallel printheads rather than one nozzle doing the whole metallization step. With the respective automation concept, printing has been demonstrated at up to 400 millimeters per second. A shuttle transport platform can handle up to 4,000 cells per lane, and the steady-movement advantage means the substrate never has to really stop.
In this short video, you can learn:
* Nozzles down to eight microns have dispensed fingers down to 12 microns, beyond the current 30-micron comfort range.
* Parallel printheads, not a single nozzle for all metallization, support demonstrated speeds up to 400 millimeters per second.
* A shuttle transport platform allows up to 4,000 cells per lane while maintaining steady movement so the substrate never really stops.
📋 **Clip Abstract** Contactless dispensing is comfortable at 30-micron finger widths, yet nozzle-material interaction with screen-printing-oriented inks around 1,000 pascal seconds and high metal loading sets the practical range. Nozzles down to eight microns have produced 12-micron fingers, while parallel printheads, 400-millimeter-per-second printing, and shuttle transport up to 4,000 cells per lane address throughput.
About the speaker:
* Speaker: Marian Breitenbuecher
* Company: HighLine Technology Gmbh
* Event: Perovskite Connect 2026 | Berlin
* Location: Estrel, Berlin
Save the date: Perovskite Connect 2027 | 20 and 21 OCT 2027 | Berlin
Co-located with the Future of Electronics RESHAPED conference and exhibition
Learn more: https://www.techblick.com/perovskiteconnect
Intestered in exhibiting: learn more here: https://www.techblick.com/perovskiteconnect
#ContactlessDispensing, #ParallelPrintheads, #HighMetalLoading, #TwelveMicronFingers, #PerovskiteSolarCells, #SolarCellMetallization
About this talk
→ Enabling Contactless Metallization for Perovskite Devices through Flexible and scalable Dispensing · Marian Breitenbuecher · Perovskite Connect 2026


