Martin Shulevski | Fraunhofer-Institut fรผr Lasertechnik ILT: Can laser-functionalized inkjet strain gauges replace manual sensor application for structural health monitoring?
02:25 - 03:38
Other snippets from this talk
Summary of the clip:
Can laser-functionalized inkjet strain gauges replace manual sensor application for structural health monitoring?
The motivation is strain gauges on components for structural health monitoring. Manual sensor application has already been used and is described as reproducible and reliable, but it is time-consuming, shows variations and is prone to errors from manual application. Additive manufacturing and laser processing are being tried to address that.
Project results have tried additive laser scribing and laser application of conductive traces. In one example, a laser-printed metallic component received an isolation layer, an inkjet-printed sensor was laser functionalized to be precisely conductive at a specific resistance or conductivity, and it was connected to a Bluetooth module for wireless telemetry.
Data from tensile and force tests were characterized. That is the motivation, but when looking at the state of the art, there are still so many problems to tackle because these are complex systems, and more work is needed.
In this short video, you can learn:
* Manual strain-gauge application is reproducible and reliable but time-consuming, varied and prone to manual errors.
* The project example used additive laser scribing, an isolation layer, an inkjet-printed sensor, laser functionalization and a Bluetooth module for wireless telemetry.
* Tensile and force tests characterized the data, while the state of the art still has many problems because these are complex systems.
๐ **Clip Abstract** Strain gauges for structural health monitoring have been applied manually, which is reproducible and reliable but time-consuming and error-prone. Project results combine additive laser scribing, an isolation layer, an inkjet-printed sensor functionalized by laser, and Bluetooth wireless telemetry, with data characterized from tensile and force tests.
About the speaker:
* Speaker: Martin Shulevski
* Company: Fraunhofer-Institut fรผr Lasertechnik ILT
* Event: Electronics RESHAPED 2026 | Berlin
* Location: Estrel, Berlin
USA: The Future of Electronics RESHAPED | USA
๐
Save the date: 9 and 10 June 2027
๐ Mountain View, California (Silicon Valley)
๐ Info: https://www.techblick.com/electronicsreshapedusa
Europe
The Future of Electronics RESHAPED | Berlin
๐
Save the date: 20 and 21 October 2027
๐ Berlin, Germany
๐ Info: https://www.techblick.com/electronicsreshaped
#LaserScribing, #InkjetStrainGauge, #LaserFunctionalization, #WirelessTelemetry, #PrintedElectronics, #StructuralHealthMonitoring
This is a highlight of the presentation:
Laser Processing for Printed Electronics: Recent Developments
More Highlights from the same talk.
05:33 - 07:21
How does laser sintering morphology translate into resistance, and how tightly can the process hit target values?
How does laser sintering morphology translate into resistance, and how tightly can the process hit target values?
A dried liquid coating is scanned by a laser to sinter metallic conductive particles, fusing them into sinter necks and thereby adjusting conductivity. Scanning strategies must provide sufficient overlap for energy input, allowing an energy density still in the microsecond range. SEM imaging shows surface oxidation in the thin films is minimized to a high degree.
Laser sintering for printed electronics is not new, and many manufacturers at the tech week are doing it. The research targets the causality effect: if sintering tweaks morphology, how does that translate into sensory signals, and where are the challenges? That area is described as very, very tricky.
In the left diagram, the X-axis is laser power and the Y-axis is resistance measured by four-point measurements. Curves show laser sintering of substrates; colors denote different optics focusing the laser irradiation beam differently, giving different energy density inputs. The tendency is the same, confirmed by laser-physics theory, and can be tweaked back and forth to hit target values precisely. Standard deviation reaches below 4%.
In this short video, you can learn:
* Different focusing optics change energy density inputs, but the resistance-versus-laser-power tendency remains the same.
* SEM imaging indicates surface oxidation in thin films is minimized to a high degree.
* The reported standard deviation is below 4%, allowing target values to be hit precisely.
๐ **Clip Abstract** Laser scanning of dried metallic coatings fuses particles into sinter necks, adjusting conductivity while minimizing thin-film surface oxidation. By varying optics and energy density, the resistance trend follows laser-physics theory, and the process reaches standard deviations below 4% to hit target values precisely.
About the speaker:
* Speaker: Martin Shulevski
* Company: Fraunhofer-Institut fรผr Lasertechnik ILT
* Event: Electronics RESHAPED 2026 | Berlin
* Location: Estrel, Berlin
USA: The Future of Electronics RESHAPED | USA
๐
Save the date: 9 and 10 June 2027
๐ Mountain View, California (Silicon Valley)
๐ Info: https://www.techblick.com/electronicsreshapedusa
Europe
The Future of Electronics RESHAPED | Berlin
๐
Save the date: 20 and 21 October 2027
๐ Berlin, Germany
๐ Info: https://www.techblick.com/electronicsreshaped
#LaserSintering, #SinterNecks, #FourPointMeasurement, #SurfaceOxidation, #PrintedElectronics, #AdditiveElectronics
12:21 - 14:17
Can terahertz scanning measure and correct laser-sintered conductivity inline without damaging thin films?
Can terahertz scanning measure and correct laser-sintered conductivity inline without damaging thin films?
Because sintering processes are fickle and deviate outside the window, inline additive sensor printing demands contactless measurement โ four-point probe needles would damage the thin-film system. The project therefore built a far-field terahertz scanner-based system, shown implemented in an inline process, and characterised an inkjet-printed conductive structure produced at different laser powers to induce different morphologies.
From the terahertz amplitude the team translated and calculated complex resistance, reading what had happened and what the resistance was. Prior characterisation of the silver nanoparticle systems told them which laser power to return with, re-sintering or adding a second sintering step to adjust conductivity and pull the values back to more or less one resistance.
Near-field terahertz measurements with partner Photemix used different laser parameters for crystallisation of an amorphous silicon wafer, and the picked-up signal formed a Mona Lisa image. The approach suits contactless characterisation of strain gauges, where selective re-sintering plus adjusted pre- and post-processing and laser parameters give a material-efficient route already being implemented by industrial partners.
In this short video, you can learn:
* Four-point probe needles can damage thin films, so the project replaced them with a far-field terahertz scanner integrated into an inline process.
* Terahertz amplitude was translated into complex resistance, and known silver nanoparticle characterisation identified the laser power for a second sintering step that normalised conductivity.
* Near-field terahertz mapping of laser-crystallised amorphous silicon reproduced a Mona Lisa image, demonstrating contactless strain-gauge characterisation and selective re-sintering.
๐ **Clip Abstract** Inline additive printing of sensors is fickle, so far-field terahertz scanning measures inkjet-printed silver structures contactlessly, converting amplitude into complex resistance without probe damage. Known nanoparticle behaviour then sets the laser power for a corrective second sintering step, while near-field terahertz mapping of laser-crystallised silicon shows the same platform imaging and characterising devices such as strain gauges.
About the speaker:
* Speaker: Martin Shulevski
* Company: Fraunhofer-Institut fรผr Lasertechnik ILT
* Event: Electronics RESHAPED 2026 | Berlin
* Location: Estrel, Berlin
USA: The Future of Electronics RESHAPED | USA
๐
Save the date: 9 and 10 June 2027
๐ Mountain View, California (Silicon Valley)
๐ Info: https://www.techblick.com/electronicsreshapedusa
Europe
The Future of Electronics RESHAPED | Berlin
๐
Save the date: 20 and 21 October 2027
๐ Berlin, Germany
๐ Info: https://www.techblick.com/electronicsreshaped
#TerahertzScanning, #SilverNanoparticleInk, #LaserSintering, #InkjetPrintedStrainGauges, #PrintedElectronics, #AdditiveManufacturing
10:58 - 12:05
How close to bulk conductivity does a custom copper-nickel ink get after laser adjustment, and how wide is its process window?
How close to bulk conductivity does a custom copper-nickel ink get after laser adjustment, and how wide is its process window?
Because copper-nickel ink is in short supply on the market, the team formulated its own ink specifically adjusted for a laser process, choosing solvents that can be controlled well enough to evaporate. Commercial inks used for inkjet were also part of the wider materials screening that preceded this in-house formulation.
Laser parameter tests were run on a large-area doctor-blade coating inside a nitrogen protective gas chamber to minimise oxidation. Resistance formed the Z axis against two varying laser parameters, and the measurements revealed a diagonal band of parameters that worked very well for the process.
Inside that diagonal window, specific resistance was extracted using a four-point measurement. The resulting conductivity was reported as very low relative to bulk, so the laser-adjusted copper-nickel route remains far from bulk values, and the usable process space appears as a narrow diagonal rather than a broad plateau.
In this short video, you can learn:
* A copper-nickel ink was developed in-house and adjusted for laser processing by controlling the solvents so they evaporate.
* Doctor-blade coatings processed in a nitrogen chamber enabled large-area mapping of resistance against two laser parameters.
* Four-point measurement showed a diagonal working window, but conductivity stayed very low compared with bulk copper-nickel.
๐ **Clip Abstract** A custom copper-nickel ink was tuned for a laser process, coated by doctor blade and tested in nitrogen to limit oxidation. Mapping resistance against two laser parameters exposed a diagonal working window, where four-point measurements gave conductivity still very low relative to bulk.,Four-point measurement confirmed a diagonal parameter band with conductivity still very low relative to bulk.
About the speaker:
* Speaker: Martin Shulevski
* Company: Fraunhofer-Institut fรผr Lasertechnik ILT
* Event: Electronics RESHAPED 2026 | Berlin
* Location: Estrel, Berlin
USA: The Future of Electronics RESHAPED | USA
๐
Save the date: 9 and 10 June 2027
๐ Mountain View, California (Silicon Valley)
๐ Info: https://www.techblick.com/electronicsreshapedusa
Europe
The Future of Electronics RESHAPED | Berlin
๐
Save the date: 20 and 21 October 2027
๐ Berlin, Germany
๐ Info: https://www.techblick.com/electronicsreshaped
#CopperNickelInk, #LaserParameterWindow, #FourPointMeasurement, #NitrogenAtmosphere, #PrintedElectronics, #AdditiveManufacturing
About this talk
โ Laser Processing for Printed Electronics: Recent Developments ยท Martin Shulevski ยท The Future of Electronics RESHAPED 2026 Berlin


