top of page

Matteo Iacomini

Coatema Coating Machinery GmbH

* All members of the platform can watch the entire presentation.

 

Please register to become a member.

Matteo Iacomini | Coatema Coating Machinery GmbH: Why can you change the shim and coating gap without changing wet coating thickness at all?

07:07 - 08:45

Other snippets from this talk

Summary of the clip:

Why can you change the shim and coating gap without changing wet coating thickness at all?

Slot die coating is a pre-metered system: whatever enters the die eventually comes out. The wet coating thickness follows from pump volume divided by substrate speed, so the pump volume equals substrate speed multiplied by wet coating thickness. This ideal relation means the process must rely on very well-defined pump accuracy. Any pump-volume error directly changes the deposited wet layer, because the die is not a passive reservoir but a metering element.

A critical point is that wet coating thickness does not depend on two important slot-die parameters: shim thickness and coating gap. They remain important mechanical parts of the slot die, but they do not set the coating thickness. That independence is why shim and gap changes can be made without changing the wet deposited thickness, provided the pump volume and substrate speed stay fixed. The ideal formula therefore separates metering from die geometry.

Real slot dies are not ideal elements. A slot die is a finite mechanical part with boundaries and edges, so the ink fills boundary conditions and viscosity causes shear on those edges. This shear produces defects and makes the blue rectangle only an average coating thickness. Instead of a uniform layer, the edges become thinner while mass conservation makes the center thicker. The target rectangle is the desired average, but edge shear and conservation reshape the actual cross-section.

In this short video, you can learn:
* Wet coating thickness in slot die coating is set by pump volume divided by substrate speed, so pump accuracy dominates.
* Shim thickness and coating gap are important slot-die parts, yet they do not change wet coating thickness.
* Because a real die has finite edges and shear, the coating is thinner at edges and thicker in the center through mass conservation.

📋 **Clip Abstract** Slot die coating is pre-metered: wet thickness follows from pump volume and substrate speed, not from shim thickness or coating gap. Real dies still introduce edge shear and mass-conservation effects, so the uniform blue rectangle is only an average and the actual profile becomes thinner at edges and thicker in the center.

About the speaker:
* Speaker: Matteo Iacomini
* Company: Coatema Coating Machinery GmbH
* Event: The Future of Electronics RESHAPED 2025
* Location: Estrel, Berlin

🗓️ Save the date for the next Future of Electronic RESHAPED conference and exhibition
USA | Mountain View | 9-10 June 2027 : https://www.techblick.com/electronicsreshapedusa
Europe | Berlin | 20-21 October 2027: https://www.techblick.com/electronicsreshaped

#SlotDieCoating, #PreMeteredCoating, #WetCoatingThickness, #EdgeShear, #PrintedElectronics, #AdditiveElectronics

This is a highlight of the presentation:

Slot Die Coating: Principles and Practice Towards Mass Production

The Future of Electronics RESHAPED 2025 | Berlin

​

22-23 October 2025

Estrel, Berlin

Organised By:

TechBlick

​

More Highlights from the same talk.

09:21 - 11:32

Why does shim thickness, not pump pressure, dominate slot-die cross-web uniformity?

Why does shim thickness, not pump pressure, dominate slot-die cross-web uniformity?

To achieve uniform slot-die coating, the pressure drop inside the slot must greatly exceed the pressure drop within the manifold. This pressure inequality ensures that the ink, entering from a point source, fully distributes and fills the manifold before passing through the slot. The controlling equation reveals that while slot length, width, and ink viscosity play roles, the shim thickness is the most critical parameter due to its cubic dependency.

The cubic relationship means that selecting the shim thickness directly dictates pressure build-up. A thick shim results in very low pressure, whereas a thin shim dramatically increases pressure and compresses the ink. Operating pressures must be carefully balanced between mechanical and fluidic limits. If the pressure exceeds one to two bars, the slot die itself can mechanically deform under the intense ink pressure, disrupting the coating process.

Conversely, the lower operating limit is set at 0.1 bar. Below this threshold, the shim is too thick, meaning the ink encounters virtually no resistance and fails to fill the manifold. Instead, the fluid simply flows down the center of the die, resulting in severe cross-web coating non-uniformity. To optimize this behavior, engineers model the manifold geometry as a cylinder to map fluid dynamics accurately.

In this short video, you can learn:
* The pressure drop in the slot must be significantly larger than the pressure drop in the manifold to ensure even ink distribution.
* Shim thickness has a cubic dependency on pressure, making it the dominant geometrical factor for controlling ink compression.
* Operating pressures must stay between 0.1 bar to prevent center-pooling and 1 to 2 bar to avoid mechanical die deformation.

📋 **Clip Abstract** This technical overview explains how shim thickness dictates pressure distribution and coating uniformity in slot-die systems. By balancing fluidic resistance between 0.1 and 2.0 bar, operators can prevent both mechanical die deformation and center-pooling defects.

About the speaker:
* Speaker: Matteo Iacomini
* Company: Coatema Coating Machinery GmbH
* Event: The Future of Electronics RESHAPED 2025
* Location: Estrel, Berlin

🗓️ Save the date for the next Future of Electronic RESHAPED conference and exhibition
USA | Mountain View | 9-10 June 2027 : https://www.techblick.com/electronicsreshapedusa
Europe | Berlin | 20-21 October 2027: https://www.techblick.com/electronicsreshaped

#ConductiveInks, #SlotDieCoating, #CoatemaMachinery, #CoatingUniformity, #PrintedElectronics, #RollToRoll

27:09 - 29:21

How do you cut and restart a coating meniscus faster than pump reversal or die movement?

How do you cut and restart a coating meniscus faster than pump reversal or die movement?

Standard methods to interrupt coating include stopping the pump, reversing and restarting it, which stops the meniscus, or moving the whole body back and forth, a mechanical movement that breaks the meniscus accordingly. Alternatively, you can work internally in the die, redirecting flow with shutters or valves while the pump still moves and pumps your ink in a controlled way. These modes can be used singularly or in combination, but they are too slow.

If viscosity is high, this is okay: ink can stop the way you want. For lower viscosity, cut definition suffers. A fuel-cell application used movement back and forth in coating, forming nice edges by displacement, but this was for high-viscosity fluids. Moving down to lower-viscosity materials, as in an olive application, gives leading and trading that are not really precise. Braking is not enough, not fast enough, so you need something steadier and faster in suck back and restoration.

A developed system involves a bending slot that can produce, with piezo electric control, these kinds of movements. The slot expands the slot volume, so the cut happens at the lips, at the very lips. The interesting thing is cutting the meniscus at the very lip end across the whole width of your coating. This works better for lower-viscosity things.

In this short video, you can learn:
* Pump reversal, die-body movement and internal flow redirection with shutters or valves are too slow for low-viscosity inks.
* High-viscosity fluids tolerate displacement cutting, but lower-viscosity materials show imprecise leading and trading and braking that is not fast enough.
* A bending slot with piezo electric control expands slot volume and cuts the meniscus at the very lip end across the whole coating width, working better for lower-viscosity things.

📋 **Clip Abstract** The clip compares mechanical and internal methods for stopping a coating meniscus: pump reversal, moving the die body, and shutters or valves that redirect flow while the pump keeps pumping. It then presents a piezo electric bending slot that expands slot volume and cuts the meniscus at the very lips across the full coating width, working better for lower-viscosity inks.

About the speaker:
* Speaker: Matteo Iacomini
* Company: Coatema Coating Machinery GmbH
* Event: The Future of Electronics RESHAPED 2025
* Location: Estrel, Berlin

🗓️ Save the date for the next Future of Electronic RESHAPED conference and exhibition
USA | Mountain View | 9-10 June 2027 : https://www.techblick.com/electronicsreshapedusa
Europe | Berlin | 20-21 October 2027: https://www.techblick.com/electronicsreshaped

#SlotDieCoating, #BendingSlot, #MeniscusCut, #LowViscosityInks, #PrintedElectronics, #RollToRollElectronics

24:41 - 26:21

Why does ±20 µm capillary overspill ruin a 100 µm stripe but not a half-metre coating?

Why does ±20 µm capillary overspill ruin a 100 µm stripe but not a half-metre coating?

Level two uses appropriate shims, laser cut from steel, with defined fingers. These can be cut down to some hundreds of micrometer for individual stripes. But a different shim alone is not the whole solution. If you just apply it, defects occur: capillary extension. Because of the thin gap, ink invades the space. That matters when the stripe is very thin. This sets up why overspill scales with stripe width.

With a half metre of coating, expanding by 20 microns is not an issue. With a 100 micron stripe, getting plus or minus 20 can get ugly, especially for printed electrodes. In OPV, you may print something that must be conductive to a point, then isolating, and print on top of other layers. Ugly shortcuts appear. That is exactly what you do not want.

The meniscus guide is the negative of your shim. You come out of your lips with some teeth, which helps pin the meniscus better on these points. This pinning prevents the ink from expanding on the sides. It addresses the capillary extension that a plain shim allows. That is the practical route to cleaner stripe edges and fewer shortcuts when printing conductive patterns.

In this short video, you can learn:
* Appropriate shims can define individual stripes down to hundreds of micrometres, but a different shim alone can cause capillary extension.
* A 20-micron expansion is tolerable on a half-metre coating but can be ugly on a 100-micron stripe, especially printed electrodes or OPV.
* A meniscus guide, the negative of the shim, uses teeth to pin the meniscus and prevent ink expanding on the sides.

📋 **Clip Abstract** Stripe patterning relies on shims that can be laser cut from steel and define fingers down to hundreds of micrometres, yet capillary extension in the thin gap can widen a 100 µm stripe by ±20 µm while a half-metre coating tolerates the same overspill. A meniscus guide—the negative of the shim—with teeth at the lips pins the meniscus better and stops the ink expanding sideways, avoiding shortcuts in printed electrodes and OPV stacks.

About the speaker:
* Speaker: Matteo Iacomini
* Company: Coatema Coating Machinery GmbH
* Event: The Future of Electronics RESHAPED 2025
* Location: Estrel, Berlin

🗓️ Save the date for the next Future of Electronic RESHAPED conference and exhibition
USA | Mountain View | 9-10 June 2027 : https://www.techblick.com/electronicsreshapedusa
Europe | Berlin | 20-21 October 2027: https://www.techblick.com/electronicsreshaped

#ShimPatterning, #CapillaryExtension, #MeniscusGuide, #OPVElectrodes, #PrintedElectronics, #AdditiveElectronics

Links to this speaker's talk page and other highlights appear here.

More Snippets
CONTACT US

KGH Concepts GmbH

Mergenthalerallee 73-75, 65760, Eschborn

+49 17661704139

admin@techblick.com

TechBlick is owned and operated by KGH Concepts GmbH

Registration number HRB 121362

VAT number: DE 337022439

  • LinkedIn
  • YouTube

Sign up for our newsletter to receive updates on our latest speakers and events AND to receive analyst-written summaries of the key talks and happenings in our events.

Thanks for submitting!

© 2026 by KGH Concepts GmbH

bottom of page