Neil Spann | Power Roll: How does a micro-groove architecture eliminate transparent electrodes and tolerate perovskite pinholes?
02:33 - 04:38
Other snippets from this talk
Summary of the clip:
How does a micro-groove architecture eliminate transparent electrodes and tolerate perovskite pinholes?
The architecture rotates the solar cell through 90 degrees: electrodes sit on the sides, not top and bottom, and the cell shrinks to a micro groove roughly 1.2 microns wide and 1.2 microns deep. That microscopic geometry removes the need for transparent electrodes, including ITO, and changes how the device tolerates defects.
Because electrodes are on the sides of the microstructures, pinholes cannot short-circuit them. Skipping a few micro grooves does not materially change the overall module, so the architecture is resistant to manufacturing defects. The parallel and series connections are made when the pattern is put into the plastic, avoiding P1, P2 and P3 scribing.
The large number of cells and modules gives a virtually linear shading response: losing 1,000 cells does not make a material difference to the rest of the module. The micro-groove design is also highly bifacial in a single cell without additional processes, delivering a 92% or 0.92 bifaciality factor, virtually the same whichever way.
In this short video, you can learn:
* Side electrodes in 1.2-micron micro grooves remove the need for transparent electrodes such as ITO.
* Pinholes cannot short-circuit side electrodes, and skipping grooves does not materially affect module output.
* Connections are patterned into the plastic without P1/P2/P3 scribing, and the module has a 0.92 bifaciality factor.
đź“‹ **Clip Abstract** The architecture rotates the solar cell 90 degrees so electrodes sit on the sides of 1.2-micron-wide, 1.2-micron-deep micro grooves, eliminating transparent electrodes and making pinholes non-shorting. Series and parallel connections are patterned into the plastic without P1/P2/P3 scribing, while many cells produce linear shading response and a 0.92 bifaciality factor.
About the speaker:
* Speaker: Neil Spann
* Company: Power Roll
* Event: Perovskite Connect 2026 | Berlin
* Location: Estrel, Berlin
Save the date: Perovskite Connect 2027 | 20 and 21 OCT 2027 | Berlin
Co-located with the Future of Electronics RESHAPED conference and exhibition
Learn more: https://www.techblick.com/perovskiteconnect
Intestered in exhibiting: learn more here: https://www.techblick.com/perovskiteconnect
#ITOFreeElectrodes, #MicroGrooveArchitecture, #PinholeTolerance, #BifacialityFactor, #PerovskitePhotovoltaics, #ThinFilmSolar
This is a highlight of the presentation:
An ITO free micro-groove architecture for low cost scalable perovskite modules
21 and 22 OCT 2026
Estrel, Berlin
Organised By:
More Highlights from the same talk.
04:46 - 06:29
What four roll-to-roll steps make micro-groove perovskite modules low cost and scalable?
What four roll-to-roll steps make micro-groove perovskite modules low cost and scalable?
Step one embosses the micro-groove pattern into a PET substrate. The same machine that makes a hologram makes the micro-groove pattern; this is outsourced to a very large strategic in Europe, which sends kilometers of film with the pattern already embossed. At that point the series and parallel connections are ready to be created, making a super low-cost route.
Step two uses vapor deposition to deposit the electrodes, the ETL and the HTL layer on the sides of the microstructures; there is quite unique IP in how this is done, though vapor deposition is widely used. Step three slot-dies the perovskite across the film. Steps one, two and three are fully done and proven roll-to-roll on a 100-millimeter-wide pilot line in the northeast, and the process is clearly scalable.
Step four puts down very simple busbars: one side of the film is always positive and one side is always negative. Two simple busbars plus lamination make a solar module. The result is an incredibly simple way to make solar cells, designed from the outset for low-cost roll-to-roll production.
In this short video, you can learn:
* The micro-groove pattern is embossed into PET film using the same machine type used for holograms, then supplied in kilometers by a large European strategic.
* Vapor deposition forms electrodes, ETL and HTL on the microstructure sides, while slot-die coating applies perovskite; all first three steps are proven roll-to-roll.
* The 100-millimeter-wide pilot line uses two simple busbars—one positive side, one negative side—plus lamination to make a module.
đź“‹ **Clip Abstract** A four-step roll-to-roll route embosses micro-grooves into PET, vapor-deposits electrodes, ETL and HTL on the microstructure sides, slot-dies perovskite, then adds simple busbars and lamination. Steps one to three are proven roll-to-roll on a 100-millimeter-wide pilot line, with busbars giving one positive and one negative side for module assembly.
About the speaker:
* Speaker: Neil Spann
* Company: Power Roll
* Event: Perovskite Connect 2026 | Berlin
* Location: Estrel, Berlin
Save the date: Perovskite Connect 2027 | 20 and 21 OCT 2027 | Berlin
Co-located with the Future of Electronics RESHAPED conference and exhibition
Learn more: https://www.techblick.com/perovskiteconnect
Intestered in exhibiting: learn more here: https://www.techblick.com/perovskiteconnect
#MicroGrooveEmbossing, #VaporDeposition, #SlotDiePerovskite, #PETSubstrate, #PerovskiteSolar, #RollToRollManufacturing
14:54 - 16:40
Can a 15.5% cell architecture scale without replicating efficiency, while still short of 1,000-hour durability?
Can a 15.5% cell architecture scale without replicating efficiency, while still short of 1,000-hour durability?
The architecture connects about 400 solar cells microscopically and has shown 15.5%, but that result has not yet been fully replicated at mass scale; modules are therefore below it. Durability work combines accelerated age testing with field testing, and the thousand-hour test has not yet been passed. The architecture itself is not framed as the fundamental challenge.
The target is a 15-year life to begin with, with longer lifetimes expected later. Reaching that depends on getting the perovskite correct and selecting the right encapsulation system around it. Low-cost economics and extremely simple adhesive deployment are intended to bring LCU to an acceptable level, even with that initial lifetime.
Against other perovskite companies, the claimed differentiators are elimination of ITO, a costly and challenging material, fewer process steps—particularly on electrical connections—and enhanced angular and shading response versus standard planar devices. The market is expected to be large enough for many companies, much as silicon has many suppliers rather than one.
In this short video, you can learn:
* The architecture has demonstrated 15.5% but has not yet fully replicated that efficiency at mass scale, so modules remain below it.
* Durability testing includes accelerated aging and field testing, but the thousand-hour test has not yet been passed.
* The 15-year initial lifetime target depends on perovskite quality and encapsulation, while ITO elimination and fewer process steps support low-cost positioning.
đź“‹ **Clip Abstract** A microscopically connected architecture of about 400 solar cells has shown 15.5%, though mass-scale modules are below that and the thousand-hour durability test has not yet been passed. The commercial case targets a 15-year initial life, low LCU through simple adhesive deployment, ITO elimination, fewer process steps and enhanced angular and shading response versus planar devices.
About the speaker:
* Speaker: Neil Spann
* Company: Power Roll
* Event: Perovskite Connect 2026 | Berlin
* Location: Estrel, Berlin
Save the date: Perovskite Connect 2027 | 20 and 21 OCT 2027 | Berlin
Co-located with the Future of Electronics RESHAPED conference and exhibition
Learn more: https://www.techblick.com/perovskiteconnect
Intestered in exhibiting: learn more here: https://www.techblick.com/perovskiteconnect
#PerovskiteEncapsulation, #ITOElimination, #AngularShadingResponse, #ThousandHourTest, #PerovskiteSolar, #SolarModuleDurability
09:34 - 11:47
How does micro-groove solar film maintain linear output under partial shading, physical damage, and varied installation angles?
How does micro-groove solar film maintain linear output under partial shading, physical damage, and varied installation angles?
The micro-groove architecture removes ITO and uses low-cost production steps. With the UK National Physical Laboratory, physical—not modeled—measurements compare the film’s angular response against planar at different deployment angles. The blue curve shows a shoulder that extends energy capture across angles, which the speaker links to significant enhancements for vertical, flat and curved deployments.
Shading tests from 10% through 100% produce an almost normalized, linear response versus an unshaded panel. The same behavior applies to damage and defects: after punching holes, only the impacted area is lost. This property is presented as unique for both production and deployment of the solar film.
The real-world targets are partially shaded environments, building sides in BIPV, and bifacial east-west deployment. Vertically oriented, the film is said to generate more electrons than standard technologies. In east-west bifacial deployment, single-junction cells show a nice M curve: generation in the east and west, a midday dip, and some bounce-back effect.
In this short video, you can learn:
* Physical NPL measurements show the micro-groove film’s angular response has a shoulder versus planar, extending energy from different angles for vertical, flat and curved deployments.
* Shading from 10% to 100% and punched holes yield an almost normalized linear response, with loss limited to the impacted area.
* East-west bifacial deployment produces an M-shaped single-junction curve with east and west generation, a midday dip and bounce-back.
đź“‹ **Clip Abstract** Micro-groove solar film is presented as ITO-free with low-cost production steps, and National Physical Laboratory measurements show an angular-response shoulder versus planar films. Shading from 10% to 100% and physical holes give an almost normalized linear response, enabling partially shaded BIPV, vertical building-side and east-west bifacial deployments with an M-shaped generation curve.
About the speaker:
* Speaker: Neil Spann
* Company: Power Roll
* Event: Perovskite Connect 2026 | Berlin
* Location: Estrel, Berlin
Save the date: Perovskite Connect 2027 | 20 and 21 OCT 2027 | Berlin
Co-located with the Future of Electronics RESHAPED conference and exhibition
Learn more: https://www.techblick.com/perovskiteconnect
Intestered in exhibiting: learn more here: https://www.techblick.com/perovskiteconnect
#MicroGrooveArchitecture, #ITOFreeElectrodes, #AngularResponse, #LinearShadingResponse, #BIPV, #PerovskitePV
About this talk
→ An ITO free micro-groove architecture for low cost scalable perovskite modules · Neil Spann · Perovskite Connect 2026


