top of page

Ofer Shochet

Copprint

* All members of the platform can watch the entire presentation.

 

Please register to become a member.

Ofer Shochet | Copprint: How can paper survive 260°C sintering for three seconds without burning?

14:33 - 15:44

Other snippets from this talk

Summary of the clip:

How can paper survive 260°C sintering for three seconds without burning?

Sintering copper without pressure still needs heat, and the number is set by the substrate rather than the metal. PET sinters at 160 degrees for 20 seconds. Polyimide tolerates 250 to 300 degrees. The paper system demonstrated here runs three seconds at 260 degrees — a different profile for every carrier.

The real constraint is not the peak temperature but the temperature budget — the two numbers get confused constantly. Asking only 'what temperature?' misses how long the material is exposed. The budget is what determines whether a polymer or paper survives the sinter, and it is the parameter that should be quoted alongside any copper ink claim.

Paper held at 260 degrees will burn — but not in three seconds. The analogy offered is a finger touching a hot plate or an oven by mistake: still fine if it is very quick. Short, intense exposure lets a cellulosic substrate pass through a sintering step that its steady-state limit would forbid.

In this short video, you can learn:
* Sintering profiles are substrate-specific: 160 degrees for 20 seconds on PET, 250 to 300 degrees on polyimide, and 260 degrees for three seconds on paper.
* The governing metric is the temperature budget, not the peak temperature, which is why the two numbers are so often confused.
* Paper survives 260 degrees because exposure lasts three seconds, likened to briefly touching a hot plate rather than soaking at that temperature.

📋 **Clip Abstract** The talk sets out how sintering temperature is dictated by the substrate: 160 degrees for 20 seconds on PET, 250 to 300 degrees on polyimide, and 260 degrees for three seconds on paper. It argues that the temperature budget, not the headline temperature, decides whether a paper substrate survives a pressureless copper sinter.

About the speaker:
* Speaker: Ofer Shochet
* Company: Copprint
* Event: Sustainable Electronics RESHAPED 2026 | Berlin
* Location: Estrel, Berlin

Sustainable Electronics RESHAPED | Berlin
📅 Save the date: 20 and 21 October 2027
📍 Berlin, Germany
📋 Info: https://www.techblick.com/sustainableelectronicsreshaped

#CopperSintering, #PaperSubstrate, #TemperatureBudget, #ThreeSecondSinter, #PrintedElectronics, #GreenRFID

This is a highlight of the presentation:

Compostable and Recyclable Electronics Without Performance Compromise: Printed Copper on Paper for Green RFID Tags at Scale

Sustainable Electronics RESHAPED 2026 | Berlin

​

20-21 OCT 2026

Estrel, Berlin

Organised By:

TechBlick

​

More Highlights from the same talk.

02:20 - 03:54

How large is the environmental burden of 50 billion RFID tags made from aluminum and PET?

How large is the environmental burden of 50 billion RFID tags made from aluminum and PET?

In 2024, more than 50 billion RFIDs were sold worldwide, with a decline in 2025 and a recovery this year. Adoption is visible in retail: walk into a Zara or Uniqlo store and every tag carries the technology, which supports supply chain visibility and, per the speaker, helps sustainability. The penetration curve shown is still early — the stated potential runs into trillions of units across industries.

Today's tags are built from what the speaker calls great stuff — aluminum and plastic. He describes the construction as a can of Coke glued to a bottle of Coke, cut into small pieces, then 50 billion of them thrown around the world. That is the material base behind RFID volumes now scaling into retail supply chains.

The aluminum fraction alone carries a quantified burden: the speaker compares it to taking more than 150 million aluminum soda cans and throwing them into the ocean every year. He signals a similar comparison for the plastic content. Against a trajectory toward trillions of units, that per-tag material mass compounds annually rather than staying fixed.

In this short video, you can learn:
* More than 50 billion RFIDs were sold in 2024, with a decline in 2025 and a recovery this year.
* Tags are today built from aluminum and plastic, described as a Coke can glued to a Coke bottle and cut into small pieces.
* The aluminum content alone equates to more than 150 million soda cans thrown into the ocean every year.

📋 **Clip Abstract** RFID volumes passed 50 billion units in 2024 and are positioned to move into the trillions across industries. The current aluminum-and-plastic construction turns that scale into an annual material burden equivalent to over 150 million soda cans dumped in the ocean.

About the speaker:
* Speaker: Ofer Shochet
* Company: Copprint
* Event: Sustainable Electronics RESHAPED 2026 | Berlin
* Location: Estrel, Berlin

Sustainable Electronics RESHAPED | Berlin
📅 Save the date: 20 and 21 October 2027
📍 Berlin, Germany
📋 Info: https://www.techblick.com/sustainableelectronicsreshaped

#RFIDTagVolume, #AluminumPlasticLaminate, #RetailSupplyChainTagging, #SodaCanEquivalent, #SustainableElectronics, #CircularElectronics

10:09 - 11:08

Why can silver ink beat carbon ink on lifecycle CO2 once resistivity is normalized?

Why can silver ink beat carbon ink on lifecycle CO2 once resistivity is normalized?

The talk challenges the assumption that carbon inks are more sustainable. Full counting requires normalizing CO2 by resistivity. Silver ink can be more sustainable than carbon inks because less silver can be used than carbon, and CO2 is divided by that usage. This reframes material comparison around conductivity rather than ink mass alone.

Against all alternatives, the calculation shows printed copper wins in any way: it has much lower CO2 and the highest conductivity. That combination gives the best CO2 emission outcome. The point is to compare materials not only on cost but also on CO2 emission, and to account for normalized performance.

The same intuition is presented as a way to avoid blanket claims that carbon inks have better sustainability. Full counting, normalized to resistivity, changes the ranking: silver ink can use a lot less material than carbon, so its CO2 burden is divided accordingly. Even then, printed copper remains the winner because it has much lower CO2 and the highest conductivity.

In this short video, you can learn:
* Full sustainability comparisons must normalize CO2 by resistivity, not compare inks by mass.
* Silver ink can be more sustainable than carbon ink because far less silver is needed and the CO2 is divided by that usage.
* Printed copper wins the calculation with much lower CO2 and highest conductivity, giving the best CO2 emission.

📋 **Clip Abstract** The clip explains that carbon inks are not automatically more sustainable than silver inks: full counting must normalize CO2 by resistivity, and much less silver can be used than carbon. It then shows printed copper wins against alternatives because it combines much lower CO2 with the highest conductivity, yielding the best CO2 emission.

About the speaker:
* Speaker: Ofer Shochet
* Company: Copprint
* Event: Sustainable Electronics RESHAPED 2026 | Berlin
* Location: Estrel, Berlin

Sustainable Electronics RESHAPED | Berlin
📅 Save the date: 20 and 21 October 2027
📍 Berlin, Germany
📋 Info: https://www.techblick.com/sustainableelectronicsreshaped

#PrintedCopper, #SilverInk, #CarbonInk, #CO2Normalization, #SustainableElectronics, #PrintedElectronics

04:23 - 05:31

Can printed copper RFID pass EN13432 compostability and ARC performance certification without any performance compromise?

Can printed copper RFID pass EN13432 compostability and ARC performance certification without any performance compromise?

The material shift is to copper ink, and it uses a lot less material than incumbent processes. Manufacturing is clean enough to be done in Europe, in this building, without a special permit. That combination matters: a lower material burden and a clean, locally permitted process route. The claim is that the printed RFID structure carries certified compostability and recyclability without giving up electrical performance.

Two end-of-life standards are cited: EN13432 and KEPE V3, the latter for repulping. Together they open both waste streams — the tag can be composted or it can be recycled by repulping. That dual-path certification is the part that matters commercially, because a compostable-only label limits collection routes while a repulpable one lets paper streams absorb the device.

Performance is the fourth and, per the speaker, most important claim: no compromise. The printed RFIDs receive ARC certification from the University of Auburn in the US, described as the gold standard for RFID performance. ARC splits tags into 20 or 30 categories — separate ones for denim, T-shirt and belt placement — and the tags end up fully certified.

In this short video, you can learn:
* Printed copper ink reduces material consumption and can be manufactured in Europe without a special permit.
* Certification covers both EN13432 composting and KEPE V3 repulping, so the tags can enter either waste stream.
* ARC certification from the University of Auburn spans 20 to 30 placement categories including denim, T-shirt and belts, with no performance compromise against aluminium etching.

📋 **Clip Abstract** Printed copper RFID tags on paper are presented as carrying certified compostability and recyclability under EN13432 and KEPE V3 repulping while still achieving ARC performance certification. The comparison baseline is aluminium etching, the most common RFID process used today.

About the speaker:
* Speaker: Ofer Shochet
* Company: Copprint
* Event: Sustainable Electronics RESHAPED 2026 | Berlin
* Location: Estrel, Berlin

Sustainable Electronics RESHAPED | Berlin
📅 Save the date: 20 and 21 October 2027
📍 Berlin, Germany
📋 Info: https://www.techblick.com/sustainableelectronicsreshaped

#CopperInkPrinting, #EN13432Composting, #KEPEV3Repulping, #ARCCertifiedRFID, #SustainableElectronics, #PrintedElectronics


About this talk

→ Compostable and Recyclable Electronics Without Performance Compromise: Printed Copper on Paper for Green RFID Tags at Scale · Ofer Shochet · Sustainable Electronics RESHAPED 2026 Berlin


Other talks by Ofer Shochet


More highlights from Ofer Shochet

More Snippets
CONTACT US

KGH Concepts GmbH

Mergenthalerallee 73-75, 65760, Eschborn

+49 17661704139

admin@techblick.com

TechBlick is owned and operated by KGH Concepts GmbH

Registration number HRB 121362

VAT number: DE 337022439

  • LinkedIn
  • YouTube

Sign up for our newsletter to receive updates on our latest speakers and events AND to receive analyst-written summaries of the key talks and happenings in our events.

Thanks for submitting!

© 2026 by KGH Concepts GmbH

bottom of page