Oliver Haupt | Coherent Corp.: Why are standard linear heaters losing ground to self-regulating exponential PTC carbon materials?
00:02:54 - 00:04:57
Other snippets from this talk
Summary of the clip:
How can next-generation microLED and automotive display fabs reconcile the demand for Gen 8 scaling with the stringent cost-of-ownership targets of automated production lines?
Low-Temperature Polycrystalline Silicon (LTPS) remains the definitive process of record for high-performance backplanes, driving both established OLED displays and emerging microLED architectures for large-format and automotive applications. To unlock true economies of scale, the industry is actively transitioning from Gen 6 to Gen 8 glass substrates. Because global display manufacturers already possess deep institutional expertise in LTPS processing, they are uniquely positioned to adapt their existing backplane circuitry to meet the rigorous drive requirements of microLED arrays.
To optimize the Cost of Ownership (COO) in these highly automated Gen 8 facilities, equipment architectures must evolve beyond legacy excimer laser annealing systems. While traditional 308 nm excimer lasers represent a mature, industry-proven standard with hundreds of active installations, Diode-Pumped Solid-State (DPSS) lasers operating at 355 nm have emerged as a highly viable alternative. These DPSS systems match the critical energy density, power output, and repetition rates of excimer sources while significantly reducing maintenance overhead and aligning with modern fab automation.
Following the critical LTPS crystallization phase, the manufacturing workflow shifts from material modification to high-throughput singulation. Integrating carbon dioxide (CO2) laser systems into the post-annealing processing line enables precise, stress-free cutting of these advanced display substrates. This hybrid approach—combining optimized solid-state annealing with reliable gas-laser cutting—provides a robust, scalable manufacturing route for next-generation display architectures.
In this short video, you can learn:
* How display manufacturers leverage existing LTPS backplane infrastructure to transition into microLED and large-format automotive display production.
* The operational and maintenance advantages of adopting 355 nm DPSS lasers over traditional 308 nm excimer lasers for LTPS annealing.
* The role of CO2 lasers in the post-annealing cutting and singulation stages of display substrate fabrication.
📋 **Clip Abstract**
The speaker discusses the scaling of LTPS backplanes to Gen 8 formats for OLED and microLED displays, comparing traditional excimer laser annealing with newer, lower-maintenance DPSS laser systems. He also introduces the role of CO2 lasers in the subsequent substrate cutting process.
🎤 Speaker: Oliver Haupt
🏢 Company: Coherent Corp.
📅 Event: Printed Electronics Innovation Day 2024
📍 Location: TechBlick | Online Platform
🌐 Learn more at the next TechBlick event: https://www.techblick.com
#PTCCarbonHeaters, #SelfRegulatingHeating, #CarbonPolymerComposites, #PositiveTemperatureCoefficient, #PrintedElectronics, #FlexibleElectronics
This is a highlight of the presentation:
More Highlights from the same talk.
04:07 - 05:27
If up to 80% of microLED display cost is material, what can a laser toolmaker do to cut cost per display?
If up to 80% of microLED display cost is material, what can a laser toolmaker do to cut cost per display?
Display makers put material at up to 80% of microLED display cost, and the compound-semiconductor side is not where an equipment maker can work. The lever discussed is different: an EP wafer costs more or less the same, so cost per display depends on how many displays can be made from one wafer. That pushes die size down and forces process work to be judged by wafer utilisation.
The clip notes many small attempts to work on processes, but argues that cost will never really come down without mass production. The two requirements have to come together: smaller die to raise displays per wafer, and a manufacturing route scaled enough to make the process economics work. That combination is the stated route to cost competitiveness.
The scope described is equipment for back planes, not back-plane production itself. The open question is whether that is enough, or whether something else must be done now to support microLED volume manufacturing. The answer implied is that tool and process development must connect to mass production rather than remain isolated attempts, because cost competitiveness depends on the whole chain coming together.
In this short video, you can learn:
* Display makers say material accounts for up to 80% of microLED display cost, which a compound-semiconductor supplier cannot address directly.
* Because EP wafer cost stays roughly the same, cost per display hinges on how many displays can be made from one wafer.
* The argument is that smaller die and mass production must arrive together, not as isolated process attempts, for microLED cost to become competitive.
📋 **Clip Abstract** The clip frames microLED cost as a material-dominated problem—up to 80% according to display makers—that cannot be solved on the compound-semiconductor side. It argues the equipment route is to increase displays per wafer through smaller die and to combine process work with mass production so the cost can become competitive.
About the speaker:
* Speaker: Oliver Haupt
* Company: Coherent
* Event: MicroLED Connect 2024
* Location: High Tech Campus, Eindhoven, Netherlands
Join the most event MicroLED, AR/VR display and Optical I/O Connect event of the year
Learn more https://www.microledconnect.com/
#MicroLEDCost, #CompoundSemiconductor, #EPWafer, #DisplaysPerWafer, #MicroLEDDisplays, #DisplayManufacturing
13:36 - 15:29
Serial transfer needs 2,400 seconds for a TV — how fast can parallel laser transfer realistically go?
Serial transfer needs 2,400 seconds for a TV — how fast can parallel laser transfer realistically go?
Serial processing uses a single laser beam or needle, transferring microLEDs one by one. At typical single-spot rates of 10 kHz or below, the arithmetic is brutal: roughly 600,000 microLEDs, about 9 million at 30–60 µm smartphone pitch needing 900 seconds, and 24 million for a TV needing 2,400 seconds.
Parallel processing changes the field interaction: a stamp or laser exposes a field and transfers many microLEDs in one shot. With the optical setup and appropriate laser sources, the stated path reaches up to 50 or 5,000 microLEDs per second; at TV-scale 400 µm pitch, reducing pitch keeps field size constant while covering more devices.
The net-time comparison is the argument for parallel laser transfer. The same 600,000 devices can be done in half a second, against the serial route’s hundreds or thousands of seconds. That is why the focus is on parallel processing: it has more potential, with movement speed of donor and receiver still a practical variable to keep in mind.
In this short video, you can learn:
* Single-spot laser processing at about 10 kHz implies 2,400 seconds net transfer time for a 24-million-microLED TV.
* Parallel stamp or laser processing exposes a field and transfers many microLEDs in one shot instead of one by one.
* The stated parallel path reaches up to 50 or 5,000 microLEDs per second, making 600,000 devices a half-second net-time calculation.
📋 **Clip Abstract** The clip compares serial and parallel microLED transfer using net-time arithmetic: single-spot 10 kHz processing implies 900 seconds for a smartphone and 2,400 seconds for a TV. Parallel stamp or laser fields, with up to 50 or 5,000 microLEDs per second cited, reduce 600,000 devices to a half-second net-time calculation and explain the focus on parallel processing.
About the speaker:
* Speaker: Oliver Haupt
* Company: Coherent
* Event: MicroLED Connect 2024
* Location: High Tech Campus, Eindhoven, Netherlands
Join the most event MicroLED, AR/VR display and Optical I/O Connect event of the year
Learn more https://www.microledconnect.com/
#SerialLaserTransfer, #ParallelLaserTransfer, #MicroLEDPitch, #NetTransferTime, #MicroLEDDisplays, #LaserProcessing
07:27 - 08:38
Can laser lift-off shrink from 20–40 minutes per wafer to a few seconds with a 248 nm line beam?
Can laser lift-off shrink from 20–40 minutes per wafer to a few seconds with a 248 nm line beam?
Customers already know how to handle shorter wavelengths in display fabs, so the discussion moves to mass production and productivity. Several attempts exist for laser lift-off. One approach uses a single, very small laser spot and wobbles the full wafer; that can take 20, 30 or 40 minutes to lift off one wafer. This is the productivity baseline the next laser approaches are measured against.
A small-field-sized laser can do the job in minutes, cutting the lift-off time versus the single-spot, full-wafer wobble. For the next productivity step, line-beam technology—already used for annealing—has been converted to 248 nanometres, a shorter wavelength, and can process a wafer in a few seconds. That minutes-to-seconds change is how laser lift-off is framed for industrialisation.
Getting the laser beam to the workpiece is a separate problem for a laser manufacturer. Different ways to do this are identified, without detail in the clip. That beam-delivery question sits alongside the lift-off productivity comparison: 20–40 minutes for single-spot full-wafer wobble, minutes for a small-field-sized laser, and a few seconds for the 248 nm line beam.
In this short video, you can learn:
* A single small spot wobbled over the full wafer can take 20, 30 or 40 minutes for one wafer's lift-off.
* A small-field-sized laser cuts lift-off to minutes, and line-beam technology converted to 248 nm can process a wafer in a few seconds.
* Beam delivery to the workpiece is a separate laser-manufacturer task with different ways to get the beam there.
📋 **Clip Abstract** In display fabs, laser lift-off productivity ranges from a single small spot wobbled over the full wafer at 20–40 minutes per wafer to a 248 nm line beam that can process a wafer in a few seconds. A small-field-sized laser sits in between at minutes, while getting the laser beam to the workpiece remains a separate beam-delivery problem.
About the speaker:
* Speaker: Oliver Haupt
* Company: Coherent
* Event: MicroLED Connect 2024
* Location: High Tech Campus, Eindhoven, Netherlands
Join the most event MicroLED, AR/VR display and Optical I/O Connect event of the year
Learn more https://www.microledconnect.com/
#LaserLiftOff, #LineBeamLaser, #SmallFieldLaser, #BeamDelivery, #MicroLEDDisplays, #DisplayFabs
Other talks by Oliver Haupt
- A Closer Look at Laser Solutions for Display Manufacturing – Now, Next, and Beyond · Printed Electronics Innovation Day | Winter 2024
- MicroLED Display Volume Manufacturing Enabled By Laser Technology. · MicroLED Connect 2024
More highlights from Oliver Haupt
- ▶ How can structural polymer degradation turn a self-regulating PTC heater into a runaway thermal hazard? · Printed Electronics Innovation Day 2024
- ▶ How does the spatial design of silver finger electrodes directly program the equilibrium temperature of a PTC carbon heater? · Printed Electronics Innovation Day 2024
- ▶ If up to 80% of microLED display cost is material, what can a laser toolmaker do to cut cost per display? · MicroLED Connect 2024
- ▶ Can laser lift-off shrink from 20–40 minutes per wafer to a few seconds with a 248 nm line beam? · MicroLED Connect 2024
- ▶ Serial transfer needs 2,400 seconds for a TV — how fast can parallel laser transfer realistically go? · MicroLED Connect 2024
- ▶ How small and how tightly spaced can microLEDs get before a laser can't pick one without touching its neighbours? · MicroLED Connect 2024


