top of page

Peng Wei

Royole

* All members of the platform can watch the entire presentation.

 

Please register to become a member.

Peng Wei | Royole: Which design parameters actually raise stretchability: island size, wire width, thickness or elastomer modulus?

15:30 - 17:25

Other snippets from this talk

Summary of the clip:

Which design parameters actually raise stretchability: island size, wire width, thickness or elastomer modulus?

The design study concluded that stretchability improves in two directions: increasing alpha, defined here as smaller islands and LEDs within the rigid or flexible element, or reducing W, the narrow stripe width. In other words, a smaller element or a narrower wire delivers a large gain. Those parameters were presented as key properties for the stretchable display design.

Using those parameters, the calculation indicated stretchability more than 10 times the material yield strain for a design with 20-micrometer microLEDs at 120 PPI. That was described as very good stretchability for the application. Finite-element analysis was then used to assist the design, and it produced a similar conclusion to the earlier calculation.

The finite-element slots related stress and strain to weld width, weld thickness, substrate thickness and elastomer modulus. From that analysis, wire width showed a high impact on stretchability. In the figure, a lower slope means higher stretchability, and narrower, smaller wire width achieved higher stretchability. This reinforced the design direction toward narrow wires.

In this short video, you can learn:
* Increasing alpha—smaller islands and LEDs in the rigid or flexible element—was found to improve stretchability.
* Reducing W, the narrow stripe or wire width, also improved stretchability and was identified as a high-impact parameter.
* A 20-micrometer microLED design at 120 PPI reached more than 10 times the material yield strain, with finite-element analysis matching the calculation trend.

📋 **Clip Abstract** A design study for stretchable displays found that smaller rigid or flexible elements and narrower wires raise stretchability, with wire width showing high impact in finite-element analysis. The calculation reported more than 10 times the material yield strain for 20-micrometer microLEDs at 120 PPI, and the analysis reached a similar conclusion.

About the speaker:
* Speaker: Peng Wei
* Company: Royole
* Event: Displays & Lighting 2021: Innovations & Market Trends

Join TechBlick to learn about the cutting edge in the display industry
https://www.techblick.com/

#StretchableDisplayDesign, #FiniteElementAnalysis, #ElastomerModulus, #MicroLED120PPI, #FlexibleElectronics, #DisplayEngineering

This is a highlight of the presentation:

Advances in the Development of Flexible & Stretchable Displays and End-Product Innovations

Displays & Lighting 2021: Innovations & Market Trends

​

14-16 July 2021

Online

Organised By:

TechBlick

​

More Highlights from the same talk.

04:45 - 06:23

How does a 300°C non-silicon TFT process undercut 400–500°C LTPS for flexible AMOLED cost?

How does a 300°C non-silicon TFT process undercut 400–500°C LTPS for flexible AMOLED cost?

The driver TFTs behind the AMOLED emission layers are not silicon. The ultra-low temperature non-silicon semiconductor process, ULT-NSSP, keeps the maximum process temperature on the production line as low as 300°C, against the 400°C to 500°C demanded by traditional low-temperature polysilicon, LTPS, TFT technology. That temperature gap is the starting point for the cost argument.

Because the process ceiling drops, several costly equipment and process steps can be skipped in the ULT-NSSP flow. The speaker frames the payoff in three parts: lower mass production cost, higher yield, and improved TFT performance. Those gains are described as mattering especially for flexible displays, where the stack and the handling constraints make every removed high-temperature step count.

ULT-NSSP is presented as more than one semiconductor material change: it is a total system innovation spanning micro-nano materials development, device design based on those materials, circuit design, process, module stacking design, and product equipment. That breadth is what allows the approach to be scaled up to mass production for flexible displays, and the mass production line has been running since 2018.

In this short video, you can learn:
* ULT-NSSP holds peak production-line process temperature to 300°C, versus 400–500°C for LTPS, using non-silicon semiconductors to drive the AMOLED emission layers.
* Skipping costly equipment and process steps is claimed to cut mass production cost while raising yield and TFT performance, most of all for flexible displays.
* The process is positioned as a total system innovation — micro-nano materials, device and circuit design, process, module stacking and equipment — that has been in mass production since 2018.

📋 **Clip Abstract** Royole's ULT-NSSP replaces silicon TFTs with a non-silicon semiconductor process capped at 300°C, well below the 400–500°C of LTPS, letting several costly equipment and process steps be skipped to lower mass production cost and lift yield and TFT performance. The company frames it as a total system innovation — micro-nano materials, device design, circuit design, process, module stacking and product equipment — scalable to flexible display mass production since 2018.

About the speaker:
* Speaker: Peng Wei
* Company: Royole
* Event: Displays & Lighting 2021: Innovations & Market Trends

Join TechBlick to learn about the cutting edge in the display industry
https://www.techblick.com/

#NonSiliconTFT, #LTPS, #AMOLED, #ModuleStackingDesign, #FlexibleDisplays, #DisplayManufacturing

12:26 - 14:44

How do you fabricate a stretchable microLED display using standard flexible-display and mass-transfer tools?

How do you fabricate a stretchable microLED display using standard flexible-display and mass-transfer tools?

Fabrication starts with a standard flexible-display backplane process: a flexible substrate is coated onto a temporary glass carrier that acts as the rigid handler. On it, active-matrix or passive-matrix ferroelectric driving circuits are built in island shapes or wavy stripes. Each island carries the rigid or flexible emitting device — micro-LEDs or other micro-ICs — while the wavy straps tie every island together both physically and electrically.

After the backplane panel is complete, micro-ICs — mini or micro-LEDs, sensors, drivers — are mass transferred and bonded onto the rigid and/or flexible islands. The transfer step is deliberately tool-agnostic: it works with pick-and-place, stamp-based, printing and self-assembling micro-LED assembly techniques, so the process can be scaled up and remain compatible with mass production rather than depending on one proprietary assembler.

Finally the whole driving circuit and device stack is encapsulated in an elastomeric material — rubber, silicone or thermoplastic elastomers — selected for low curing temperature, low modulus and high transmittance. The circuitry is then delaminated from the glass carrier, releasing the finished stretchable microdisplay. Encapsulation and delamination are therefore the last two steps that convert a conventional flexible backplane into a free-standing, stretchable display.

In this short video, you can learn:
* Island-plus-wavy-stripe layouts let a standard flexible backplane carry rigid micro-LEDs while remaining physically and electrically connected.
* Mass transfer and bonding onto the islands is compatible with pick-and-place, stamp-based, printing and self-assembling micro-LED assembly techniques.
* Low-curing-temperature, low-modulus, high-transmittance elastomer encapsulation followed by delamination yields the final stretchable microdisplay.

📋 **Clip Abstract** The stretchable microdisplay is built with standard flexible-display tooling: ferroelectric active-matrix or passive-matrix circuits on a flexible substrate over a temporary glass carrier, patterned as islands linked by wavy stripes. Micro-ICs are mass transferred onto those islands using any mainstream micro-LED assembly method, then the stack is encapsulated in a low-modulus elastomer and delaminated to release the finished device.

About the speaker:
* Speaker: Peng Wei
* Company: Royole
* Event: Displays & Lighting 2021: Innovations & Market Trends

Join TechBlick to learn about the cutting edge in the display industry
https://www.techblick.com/

#StretchableMicroLED, #MassTransferBonding, #WavyStripeIslands, #ElastomerEncapsulation, #FlexibleDisplays, #MicroLEDAssembly

06:40 - 08:32

What mechanical mechanisms—strain recovery, peeling, slippage—must be controlled to certify 1.8 million bends?

What mechanical mechanisms—strain recovery, peeling, slippage—must be controlled to certify 1.8 million bends?

A proprietary optimization model for flexible displays uses smart mechanical simulation to calculate key mechanical mechanisms: strain recovery, layer peeling, and layer slippage. The model evaluates layer strain at different bend radii across critical components, including the flexible cover, touch panel, polarizer, and thin-film encapsulation. Those calculated results are used to control and optimize foldable-display performance and mechanical behavior before physical testing.

Using these simulation results, the display performance and mechanicals can be controlled and optimized. The development and simulation work produced a high-performance flexible display for foldable applications. It passed all the different tests required for foldable smartphones: bending reliability, scratch, twist, and stretch. These tests address consumer-application requirements and validate the display's mechanical robustness under the stated test conditions.

Especially, the flexible display already passed 1.8 million bends in certified display folding reliability. That certified foldable-display result is the concrete reliability outcome from the simulation-led design and the mechanical test suite. It ties the studied strain recovery, layer peeling, and layer slippage mechanisms to a certified bend-reliability milestone for foldable applications.

In this short video, you can learn:
* The simulation model calculates strain recovery, layer peeling, and layer slippage as key mechanical mechanisms for flexible displays.
* Layer strain is evaluated at different radii for the flexible cover, touch panel, polarizer, and thin-film encapsulation.
* The flexible display passed bending reliability, scratch, twist, and stretch tests, including 1.8 million certified bends.

📋 **Clip Abstract** A proprietary mechanical simulation model calculates strain recovery, layer peeling, layer slippage, and layer strain at different radii for flexible-cover, touch-panel, polarizer, and thin-film-encapsulation layers. The resulting flexible display passed bending reliability, scratch, twist, and stretch tests, including 1.8 million certified bends for foldable applications.

About the speaker:
* Speaker: Peng Wei
* Company: Royole
* Event: Displays & Lighting 2021: Innovations & Market Trends

Join TechBlick to learn about the cutting edge in the display industry
https://www.techblick.com/

#StrainRecovery, #LayerPeeling, #ThinFilmEncapsulation, #MillionBendCertification, #FoldableDisplays, #FlexibleElectronics


About this talk

→ Advances in the Development of Flexible & Stretchable Displays and End-Product Innovations · Peng Wei · Displays & Lighting: Innovations & Market Trends 2021

More Snippets
CONTACT US

KGH Concepts GmbH

Mergenthalerallee 73-75, 65760, Eschborn

+49 17661704139

admin@techblick.com

TechBlick is owned and operated by KGH Concepts GmbH

Registration number HRB 121362

VAT number: DE 337022439

  • LinkedIn
  • YouTube

Sign up for our newsletter to receive updates on our latest speakers and events AND to receive analyst-written summaries of the key talks and happenings in our events.

Thanks for submitting!

© 2026 by KGH Concepts GmbH

bottom of page