top of page

Peter Bancken

Signify Research

* All members of the platform can watch the entire presentation.

 

Please register to become a member.

Peter Bancken | Signify Research: Can additive screen printing replace etched FR4 LED strips and eliminate a three-to-four-month Far East supply chain?

08:59 - 10:07

Other snippets from this talk

Summary of the clip:

Can additive screen printing replace etched FR4 LED strips and eliminate a three-to-four-month Far East supply chain?

It starts with an FR4 or CEM3 board, or foil, for the LED strips: copper is laminated over the board and then chemically etched away to leave the tracks. The process is subtractive by definition, removing material that was previously produced on the board, and it sits almost entirely in Far East production.

Ordering three to four months in advance is the consequence of that long supply chain. Material arrives on the shelf and waits: by the time it reaches the factory a new LED may exist, or the customer has cancelled the order, and the board is thrown away. Inventory risk and obsolescence are built into the logistics, not just the process.

The alternative is additive screen printing: you print the tracks only where you need them and size them to what is required, so material use becomes efficient. The dielectric goes just on the tracks rather than all over the board. That enables regional production, shorter lead times and less goods on stock, and since a couple of months the move toward independence from that chain.

In this short video, you can learn:
* Subtractive etching removes copper laminated over the whole board, whereas additive screen printing deposits tracks only where they are needed.
* Far East sourcing forces three-to-four-month advance ordering, so boards can be obsolete or orphaned by cancellation before reaching the factory.
* Printing dielectric only on the tracks, not all over the board, is the material-efficiency lever behind shorter lead times and less stock.

πŸ“‹ **Clip Abstract** Conventional LED strips on FR4 or CEM3 are built subtractively, with copper laminated over the board and chemically etched back to leave tracks, all of it sourced in the Far East with three-to-four-month lead times. Additive screen printing deposits tracks and dielectric only where required, cutting material waste and enabling regional production, shorter lead times and less goods on stock.

About the speaker:
* Speaker: Peter Bancken
* Company: Signify Research
* Event: Sustainable Electronics RESHAPED 2026 | Berlin
* Location: Estrel, Berlin

Sustainable Electronics RESHAPED | Berlin
πŸ“… Save the date: 20 and 21 October 2027
πŸ“ Berlin, Germany
πŸ“‹ Info: https://www.techblick.com/sustainableelectronicsreshaped

#AdditiveScreenPrinting, #SubtractiveEtching, #FR4, #DielectricDeposition, #PrintedElectronics, #SustainableElectronics

This is a highlight of the presentation:

Sustainability aspects within lighting

Sustainable Electronics RESHAPED 2026 | Berlin

​

20-21 OCT 2026

Estrel, Berlin

Organised By:

TechBlick

​

More Highlights from the same talk.

05:00 - 07:13

Where does a luminaire's carbon footprint really sit, and which design choices can reduce it?

Where does a luminaire's carbon footprint really sit, and which design choices can reduce it?

Across production, transport, use phase and end of life, the reference luminaire's climate change impact is dominated by one colour in the chart: grey. The use phase accounts for 90 to 95% of CO2 emissions, which is why electricity efficiency matters most. LED design sits largely with the supplier; system architecture and heat management offer modest in-house gains, but neither is the focus here.

The study therefore targets the production phase, and specifically the light modules. A cross-section shows the housing, an upward-looking light source, a downward light source and optics on both sides. In the component-level LCA the housing is very important, but the LED modules matter just as much. Reducing their footprint requires sustainable production technologies, sustainable materials and an end-of-life strategy.

On technology, the route is additive: additive processes make efficient use of material and energy. Eco design and a modular architecture follow, so a broken LED module does not send the whole luminaire to waste β€” you repair it or upgrade it to a more efficient module. At end of life, separating components improves the waste stream, and single-material components upgrade it further; today shredding mixes metal and polymers.

In this short video, you can learn:
* In the reference luminaire, 90–95% of climate change impact sits in the use phase, making electricity efficiency the dominant lever.
* The component LCA flags both the housing and the LED light modules as the production-phase priorities.
* Additive processes, eco design, modular architecture and single-material components are the stated routes to a better end-of-life waste stream than shredding.

πŸ“‹ **Clip Abstract** An LCA of a reference luminaire shows 90–95% of CO2 emissions in the use phase, while the production phase β€” housing and LED light modules β€” is where the study intervenes. Additive technologies, eco design, modular repair-or-upgrade architecture and single-material separation are presented as the levers on footprint and end-of-life waste.

About the speaker:
* Speaker: Peter Bancken
* Company: Signify Research
* Event: Sustainable Electronics RESHAPED 2026 | Berlin
* Location: Estrel, Berlin

Sustainable Electronics RESHAPED | Berlin
πŸ“… Save the date: 20 and 21 October 2027
πŸ“ Berlin, Germany
πŸ“‹ Info: https://www.techblick.com/sustainableelectronicsreshaped

#LuminaireComponentLCA, #UsePhaseEmissions, #ModularLEDUpgrade, #SingleMaterialWasteStream, #LifeCycleAssessment, #SustainableElectronics

13:41 - 14:57

What LCA improvement comes from reversible interconnects, additive manufacturing and single-material modularity?

What LCA improvement comes from reversible interconnects, additive manufacturing and single-material modularity?

The comparison is a cross-section. Past architectures were integral: mechanical screwing and gluing of heterogeneous materials. The modular approach slides the part in, encloses it mechanically, and arrives at a single housing material. That joint-level change is the basis for the sustainability numbers that follow, because reversibility is designed into the connection rather than added after the product is built.

In the LCA, climate change impact β€” the CO2 emission equivalent β€” drops markedly. The credited levers are modular reversible interconnects and additive manufacturing, which is flagged as very important. Material homogeneity does the end-of-life work: 82% weight percent of the product is a single material, which helps at end of life by simplifying separation and recovery.

The PCB, described as the LED foil, sees a 67% weight reduction, meaning less material and, it is hoped, less cost. Zooming out to the lighting level, energy efficiency remains very important, because 95% is still… Efficiency therefore stays the priority lever while these material-side gains accumulate underneath it.

The modular single-material housing, reversible interconnects and additive processing are what move the LCA climate change indicator.

82 weight percent of the product is one material, which is the stated benefit for end of life.

The LED foil PCB drops 67% in weight, cutting material use with a hoped-for cost reduction.

In this short video, you can learn:
* Modular reversible interconnects and additive manufacturing are the levers behind the CO2-equivalent reduction in the LCA.
* 82 weight percent of the design is a single material, which helps at end of life.
* The LED foil PCB achieves a 67% weight reduction, meaning less material and hoped-for lower cost.

πŸ“‹ **Clip Abstract** A cross-section comparison shows integral designs built by screwing and gluing heterogeneous materials giving way to a modular architecture with a single housing material. The LCA follows: CO2-equivalent climate change impact drops with reversible interconnects and additive manufacturing, 82 weight percent single material helps end of life, and the LED foil PCB loses 67% of its weight.

About the speaker:
* Speaker: Peter Bancken
* Company: Signify Research
* Event: Sustainable Electronics RESHAPED 2026 | Berlin
* Location: Estrel, Berlin

Sustainable Electronics RESHAPED | Berlin
πŸ“… Save the date: 20 and 21 October 2027
πŸ“ Berlin, Germany
πŸ“‹ Info: https://www.techblick.com/sustainableelectronicsreshaped

#ReversibleInterconnects, #SingleMaterialHousing, #AdditiveManufacturing, #EndOfLifeDisassembly, #LifeCycleAssessment, #SustainableElectronics

07:29 - 09:00

Can FDM-printed bio-based PLA and PEF replace extruded aluminum housings while keeping one-foot modularity and a single-material waste stream?

Can FDM-printed bio-based PLA and PEF replace extruded aluminum housings while keeping one-foot modularity and a single-material waste stream?

The baseline housing is extruded aluminum. The alternative is additive manufacturing, specifically FDM, supported by regional printing farms in Europe, North America and the Far East, plus sites close to customers. Conventional production uses polycarbonate; this route switches to bio-based polymers such as PLA and PEF. The claim is a more sustainable housing route that can be shown to the business and the lighting world.

Instead of a fixed design, the luminaire family uses two-, four- and five-foot formats assembled from a one-foot building block. This is the modularity mechanism: one printed unit scales the housing length. Different filling grades minimize the amount of polymer in the housing. No mechanical or thermal parity with extruded aluminum is stated, so the replacement claim is about material route and modular construction.

For end of life, the housing uses only one single material, intended to upgrade the waste stream rather than create a mixed-material recycling problem. That single-material strategy pairs with the bio-based PLA/PEF choice and the one-foot building block. The discussion stops at the light source, so no full-luminaire disassembly or recycling yield is reported.

In this short video, you can learn:
* The standard housing is extruded aluminum; the proposed route is FDM additive manufacturing with regional printing farms in Europe, North America and the Far East.
* The material shift is from polycarbonate to bio-based PLA and PEF, with two-, four- and five-foot luminaires built from a one-foot block and varied filling grades.
* End-of-life design uses only one single material to improve waste-stream upgrading; no recycling yields or full-luminaire disassembly are reported.

πŸ“‹ **Clip Abstract** The clip compares an extruded-aluminum lighting housing with an FDM additive-manufacturing route using bio-based PLA and PEF instead of polycarbonate. It shows regional printing farms, a one-foot modular building block for two-, four- and five-foot luminaires, varied filling grades to reduce polymer, and a single-material end-of-life strategy, without reporting mechanical parity or recycling yields.

About the speaker:
* Speaker: Peter Bancken
* Company: Signify Research
* Event: Sustainable Electronics RESHAPED 2026 | Berlin
* Location: Estrel, Berlin

Sustainable Electronics RESHAPED | Berlin
πŸ“… Save the date: 20 and 21 October 2027
πŸ“ Berlin, Germany
πŸ“‹ Info: https://www.techblick.com/sustainableelectronicsreshaped

#ExtrudedAluminumHousing, #FDMPrintingFarm, #BioBasedPLA, #SingleMaterialWasteStream, #SustainableLighting, #CircularElectronics

More Snippets
CONTACT US

KGH Concepts GmbH

Mergenthalerallee 73-75, 65760, Eschborn

+49 17661704139

admin@techblick.com

TechBlick is owned and operated by KGH Concepts GmbH

Registration number HRB 121362

VAT number: DE 337022439

  • LinkedIn
  • YouTube

Sign up for our newsletter to receive updates on our latest speakers and events AND to receive analyst-written summaries of the key talks and happenings in our events.

Thanks for submitting!

© 2026 by KGH Concepts GmbH

bottom of page