top of page

Rainer Beccard

Pulsar Photonics

* All members of the platform can watch the entire presentation.

 

Please register to become a member.

Rainer Beccard | Pulsar Photonics: How do picosecond or femtosecond lasers remove thin films without thermally killing the sensitive substrate?

04:30 - 06:14

Other snippets from this talk

Summary of the clip:

How do picosecond or femtosecond lasers remove thin films without thermally killing the sensitive substrate?

Ultra-short pulse lasers in the picosecond or femtosecond range are a cold process: material is blasted off faster than heat spreads into the material. The speaker notes this is why cold ablation or cold processes can work on sensitive substrates, with no heat impact and no mechanical contact.

It works for almost all materials, including glass, metals, ceramics and plastics. The process can cut, drill or work in multilayer stacks and thin films. Users can adjust selectivity or cut through a whole stack, removing very few cubic micrometers per shot or even less for extremely controllable ablation.

Conventional lasers used for cutting or welding metals act as energy sources: the beam heats metal and evaporates or melts it. For flexible electronics, just applying heat may remove metal or change surface properties, but it can also kill the substrate. Ultra-short pulses avoid that thermal route by making cold ablation controllable.

In this short video, you can learn:
* Ultra-short pulse lasers operate in the picosecond or femtosecond range and are described as a cold process.
* Cold ablation blasts material off faster than heat spreads, enabling work on sensitive substrates without heat impact or mechanical contact.
* The process handles glass, metals, ceramics, plastics, multilayer stacks and thin films, removing very few cubic micrometers per shot or less.

πŸ“‹ **Clip Abstract** Ultra-short pulse lasers in the picosecond or femtosecond range enable cold ablation by removing material faster than heat spreads into it. This allows sensitive substrates, multilayer stacks and thin films to be processed with no heat impact or mechanical contact, while selectivity or full-stack cutting remains controllable.

About the speaker:
* Speaker: Rainer Beccard
* Company: Pulsar Photonics
* Event: Electronics RESHAPED 2026 | Berlin
* Location: Estrel, Berlin

USA: The Future of Electronics RESHAPED | USA
πŸ“… Save the date: 9 and 10 June 2027
πŸ“ Mountain View, California (Silicon Valley)
πŸ“‹ Info: https://www.techblick.com/electronicsreshapedusa

Europe
The Future of Electronics RESHAPED | Berlin
πŸ“… Save the date: 20 and 21 October 2027
πŸ“ Berlin, Germany
πŸ“‹ Info: https://www.techblick.com/electronicsreshaped

#UltraShortPulseLasers, #ColdAblation, #MultilayerThinFilms, #SensitiveSubstrates, #FlexibleElectronics, #LaserProcessing

This is a highlight of the presentation:

Ultra short pulse laser processes for next generation flexible electronics

​

21 and 22 OCT 2026

Estrel, Berlin

Organised By:

TechBlick

​

More Highlights from the same talk.

06:31 - 08:37

What can one ultra-short pulse laser do across thin-film ablation, via drilling and multilayer cutting?

What can one ultra-short pulse laser do across thin-film ablation, via drilling and multilayer cutting?

A polymer carrier topped with metal or ITO can be patterned by moving the beam across the surface with the right parameters: the film is removed only where wanted, with no thermal damage, no mechanical damage because there is no mechanical tool, only light. Micrometre precision, no burn, no debris, and any two-dimensional shape because the process is numerically driven.

Via holes are drilled by single pulse, multi-pulse or trepanation, typically reaching 100 microns up to millimetre diameters, burn-free. For smaller features, proprietary optics take ultraviolet lasers down to a 1.5 micron spot size β€” an add-on that extends any existing laser machine to ultra-small hole diameters.

The same source defines lateral structures: complex contours, marking and coatings applied to the surface, and finally cutting or singulating sheets. Because drilling only requires moving the laser a little way across the sample, the cut follows directly β€” one tool covering ablation, holes, contours and sheet separation.

In this short video, you can learn:
* Ablation removes metal or ITO from polymer carriers with micrometre precision and no thermal or mechanical damage.
* Via drilling spans 100 micron to millimetre diameters burn-free, with proprietary UV optics reaching a 1.5 micron spot.
* Cutting and sheet singulation follow from drilling, since the same beam merely travels further across the sample.

πŸ“‹ **Clip Abstract** An ultra-short pulse laser platform covers thin-film ablation, via-hole drilling and cutting or singulation of sheets, all numerically driven to any two-dimensional shape. Metal and ITO are removed from polymer carriers without thermal or mechanical damage, holes run from 100 microns down to a 1.5 micron spot with dedicated UV optics, and contours or sheet separation require only moving the beam.

About the speaker:
* Speaker: Rainer Beccard
* Company: Pulsar Photonics
* Event: Electronics RESHAPED 2026 | Berlin
* Location: Estrel, Berlin

USA: The Future of Electronics RESHAPED | USA
πŸ“… Save the date: 9 and 10 June 2027
πŸ“ Mountain View, California (Silicon Valley)
πŸ“‹ Info: https://www.techblick.com/electronicsreshapedusa

Europe
The Future of Electronics RESHAPED | Berlin
πŸ“… Save the date: 20 and 21 October 2027
πŸ“ Berlin, Germany
πŸ“‹ Info: https://www.techblick.com/electronicsreshaped

#UltrashortPulseLaser, #ThinFilmAblation, #ViaHoleDrilling, #UVSpotOptics, #PrintedElectronics, #FlexibleElectronics

12:41 - 13:31

How can every laser-processed medical device be traced back years later to its process conditions?

How can every laser-processed medical device be traced back years later to its process conditions?

Quality control is a big issue because many of these products go into the medical area as medical devices. Around the detection step, an ecosystem of control and traceability methods has been implemented β€” not just inspection of the part, but the way the process data itself is handled.

All machine data that can be logged is logged, together with the process data. Data relating to the incoming product is stored: QR codes are detected, and the product is identified. Outgoing products are then identified and marked.

Everything goes into so-called auditory software. At any time later β€” ten years or so β€” every single product can be identified: how it was made, where it was made, under which conditions. If anything went wrong, that record lets you trace back and find out what went wrong.

In this short video, you can learn:
* Quality control is a big issue for laser-processed products entering the medical device area, which is why an ecosystem of control and traceability methods sits around the detection step.
* Machine data and process data are logged, incoming product data is stored via detected QR codes, and outgoing products are identified and marked.
* In the so-called auditory software, any single product can be identified ten years later β€” how and where it was made, under which conditions β€” and failures traced back.

πŸ“‹ **Clip Abstract** Laser processing of medical devices demands traceability, so machine data, process data and incoming-product QR code data are logged alongside identification and marking of outgoing parts. The so-called auditory software then lets any single product be identified a decade later, including how and where it was made and under which conditions.

About the speaker:
* Speaker: Rainer Beccard
* Company: Pulsar Photonics
* Event: Electronics RESHAPED 2026 | Berlin
* Location: Estrel, Berlin

USA: The Future of Electronics RESHAPED | USA
πŸ“… Save the date: 9 and 10 June 2027
πŸ“ Mountain View, California (Silicon Valley)
πŸ“‹ Info: https://www.techblick.com/electronicsreshapedusa

Europe
The Future of Electronics RESHAPED | Berlin
πŸ“… Save the date: 20 and 21 October 2027
πŸ“ Berlin, Germany
πŸ“‹ Info: https://www.techblick.com/electronicsreshaped

#ProcessDataLogging, #QRCodeProductIdentification, #MedicalDeviceQualityControl, #LaserProcessTraceability, #PrintedElectronics, #FlexibleElectronics

09:44 - 12:04

Can one roll-to-roll laser tool combine five processes and self-align to fiducials at micrometre precision?

Can one roll-to-roll laser tool combine five processes and self-align to fiducials at micrometre precision?

Five laser processesβ€”ablation, marking, drilling, cutting, fine cutting and all separationβ€”are integrated into a single roll-to-roll machine. The machine builder says this cuts footprint and cost because four or five separate machines are no longer needed. The same platform runs roll-to-roll, roll-to-sheet or single-sheet mode, using winding/unwinding mechanisms or robots to pick sheets.

Camera assistance recognises reference marks, fiducials or lines on pre-coded or pre-manufactured webs and automatically aligns the laser process to micrometre precision at the exact place it is needed. Further vision systems read barcodes and QR codes, so the machine identifies the device and automatically selects the correct process. Invisible ultraviolet marks can also be detected as an add-on.

Because a flexible substrate may not sit exactly in the right Z position, the tool includes automatic focus-position detection. A special probe measures the distance from the web or foil surface to the optical head, so the laser process can be focused very exactly. Inline monitoring and detection devices are presented as real production-machine details.

In this short video, you can learn:
* A single laser platform integrates ablation, marking, drilling, cutting, fine cutting and separation to reduce footprint and machine count.
* Vision alignment locks the laser process to fiducials on pre-manufactured webs at micrometre precision.
* Barcode and QR-code reading lets the machine choose the correct process automatically, and a probe maintains focus on flexible webs.

πŸ“‹ **Clip Abstract** A roll-to-roll laser machine combines five processesβ€”ablation, marking, drilling, cutting, fine cutting and separationβ€”in one footprint, operating in roll-to-roll, roll-to-sheet or sheet mode. Camera vision aligns to fiducials at micrometre precision, barcodes and QR codes select the process, UV marks can be read, and a probe detects web surface distance for automatic focus.

About the speaker:
* Speaker: Rainer Beccard
* Company: Pulsar Photonics
* Event: Electronics RESHAPED 2026 | Berlin
* Location: Estrel, Berlin

USA: The Future of Electronics RESHAPED | USA
πŸ“… Save the date: 9 and 10 June 2027
πŸ“ Mountain View, California (Silicon Valley)
πŸ“‹ Info: https://www.techblick.com/electronicsreshapedusa

Europe
The Future of Electronics RESHAPED | Berlin
πŸ“… Save the date: 20 and 21 October 2027
πŸ“ Berlin, Germany
πŸ“‹ Info: https://www.techblick.com/electronicsreshaped

#LaserAblation, #FiducialAlignment, #RollToRoll, #InlineVision, #PrintedElectronics, #FlexibleElectronics

Links to this speaker's talk page and other highlights appear here.

More Snippets
CONTACT US

KGH Concepts GmbH

Mergenthalerallee 73-75, 65760, Eschborn

+49 17661704139

admin@techblick.com

TechBlick is owned and operated by KGH Concepts GmbH

Registration number HRB 121362

VAT number: DE 337022439

  • LinkedIn
  • YouTube

Sign up for our newsletter to receive updates on our latest speakers and events AND to receive analyst-written summaries of the key talks and happenings in our events.

Thanks for submitting!

© 2026 by KGH Concepts GmbH

bottom of page