René Liebers | 3D‑Micromac AG: Can a cured liquid layer replace sapphire grinding and cut laser-liftoff fluence and cost by 25–30%?
04:18 - 05:09
Other snippets from this talk
Summary of the clip:
Can a cured liquid layer replace sapphire grinding and cut laser-liftoff fluence and cost by 25–30%?
The system is described as supporting throughputs up to 60 wafers per hour. In laser liftoff, the sapphire wafer must be ground before the liftoff process. That grinding step is framed as expensive. The proposed route is to skip grinding entirely, apply a liquid to the surface, cure it, and finally equal the surface. This sequence is presented as the alternative to the conventional sapphire-grinding preparation.
The clip links this cured-liquid approach directly to laser energy. By skipping the expensive grinding process and equalizing the surface after curing, the required laser fluence is reduced. The speaker states that this reduction in laser fluence or laser energy is the result of the process step. The same process step is also linked to a dramatic cost reduction.
The quantified outcome is a cost reduction of up to 25 to 30% with this approach. The claim is tied to replacing sapphire grinding with liquid application, curing, and surface equalization before laser liftoff. The speaker does not give a separate fluence number in this clip; the stated benefit is reduced required laser fluence or energy plus the dramatic cost reduction. Throughput of up to 60 wafers per hour is mentioned for the system.
In this short video, you can learn:
* Sapphire grinding before laser liftoff is described as an expensive process step.
* Applying and curing a liquid, then equalizing the surface, can skip that grinding step and reduce required laser fluence or energy.
* The approach is stated to cut cost by up to 25 to 30%, with system throughputs up to 60 wafers per hour.
📋 **Clip Abstract** The clip presents a laser-liftoff route that skips sapphire grinding by applying a liquid to the surface, curing it, and equalizing the surface. It states that this lowers required laser fluence or energy and reduces cost by up to 25 to 30%, with throughputs up to 60 wafers per hour mentioned for the system.
About the speaker:
* Speaker: René Liebers
* Company: 3D‑Micromac AG
* Event: MicroLED Connect 2024
* Location: High Tech Campus, Eindhoven, Netherlands
Join the most event MicroLED, AR/VR display and Optical I/O Connect event of the year
Learn more https://www.microledconnect.com/
#LaserLiftoff, #SapphireGrinding, #CuredLiquidLayer, #LaserFluence, #MicroLEDProduction, #WaferProcessing
This is a highlight of the presentation:
Revolutionizing µLED Production with Laser-Based Processes
More Highlights from the same talk.
05:09 - 06:37
How does laser-induced forward transfer hit a 5-micron µLED pitch at millions of devices per hour?
How does laser-induced forward transfer hit a 5-micron µLED pitch at millions of devices per hour?
Reducing the required laser fluence for the red emitter cuts this step by 25 to 30 percent. Those cost savings are framed as crucial for this process step, because the end devices have to be produced at low cost. The argument here is cost per device rather than raw speed, and it hinges specifically on the red-emitting portion of the workflow.
Laser-induced forward transfer is used when a pitch change has to be applied between the intermediate substrate and the final backplane, and the same machines can be reused for it. The approach is an on-the-fly process with a square laser beam and a micro safety system, because single dice must be addressed with very high throughput and very accurate positioning at the same time.
Typical µLED addressing sizes are much below 10 microns today, and the system reaches down to five microns. Calculated at that scale, millions of devices per hour can be addressed with the tool. An alternative area-wise lift-off lifts multiple dice in one run, targeting future displays with a bigger area.
Coarse
About the speaker:
* Speaker: René Liebers
* Company: 3D‑Micromac AG
* Event: MicroLED Connect 2024
* Location: High Tech Campus, Eindhoven, Netherlands
Join the most event MicroLED, AR/VR display and Optical I/O Connect event of the year
Learn more https://www.microledconnect.com/
02:40 - 04:24
Why is substrate bending strength the ultimate gatekeeper for augmented reality waveguide mass production?
Why is substrate bending strength the ultimate gatekeeper for augmented reality waveguide mass production?
Manufacturing AR eyeglasses presents steep material challenges, particularly when using diffractive waveguide combiners that must overlay digital data onto the physical world. These high-index glass eyepieces go through intensive upstream fabrication, including nanoimprint lithography and anti-reflective coatings, before being singulated from a mother wafer.
Once diced, these extremely thin, high-refractive-index glass lenses must withstand significant mechanical loads. They are subjected to picking, placing, and automated alignment during assembly, followed by the inevitable physical stresses of daily wear by the end user.
This segment explains why optimizing the bending strength of waveguide substrates post-singulation is critical to preventing crack propagation and securing high yields in AR glass assembly.
In this short video, you can learn:
* How waveguide combiners utilize total internal reflection to overlay digital projecting sources onto real-world scenes.
* The sequential manufacturing workflow of diffractive eyepieces from nano-imprint coating to wafer singulation.
* Why edge quality and bending strength determine the survival rate of waveguides during high-volume handling.
📋 **Clip Abstract** Discover the fundamental manufacturing steps and rigorous mechanical reliability standards required for AR waveguide combiners. Understand why post-dicing bending strength is the primary survival factor during automated assembly and daily wear.
#DiffractiveWaveguides, #GlassBendingStrength, #WaferSingulation, #NanoimprintLithography, #AugmentedRealityDisplays, #NearEyeDisplays
07:23 - 09:03
Why does even high-yield µLED production still require single-die repair, and what accuracy and inspection does the tool need?
Why does even high-yield µLED production still require single-die repair, and what accuracy and inspection does the tool need?
Repair is a distinct and critical process step: defective LEDs are trimmed and replaced with good LEDs. Defects can occur at every point along the display production route and are not avoidable. Even with very high yield in previous processes, defective dies remain on the final device, so a repair step is needed to achieve a perfect display without any defects.
The repair requirement is to address single dies at very high speed to reduce cost. The developed tool is described as very accurate, with high reproducibility and high dynamics. It also needs fiduciary recognition at very high accuracy to address single dice on a one-digit-micron scale, linking machine precision directly to die-level repair.
Process understanding is equally important. Quality inspection is integrated into the tools to observe single dice and the flight phase of the microLEDs. The team also cites a deep understanding of device release. Different approaches are being evaluated, with tests ongoing and results to be published soon.
In this short video, you can learn:
* Single-die repair trims defective LEDs and fills the sites with good LEDs.
* Even high-yield production leaves defective dies, making repair necessary for a defect-free display.
* The repair tool combines high accuracy, high reproducibility, high dynamics and fiduciary recognition on a one-digit-micron scale, with integrated inspection of single dice and the microLED flight phase.
📋 **Clip Abstract** Repair is unavoidable in µLED display production because defects occur along the route and defective dies remain even at high yield. The repair tool must address single dies at high speed with high accuracy, reproducibility, dynamics and fiduciary recognition, while integrated inspection observes single dice and the microLED flight phase.
About the speaker:
* Speaker: René Liebers
* Company: 3D‑Micromac AG
* Event: MicroLED Connect 2024
* Location: High Tech Campus, Eindhoven, Netherlands
Join the most event MicroLED, AR/VR display and Optical I/O Connect event of the year
Learn more https://www.microledconnect.com/
#SingleDieRepair, #FiduciaryRecognition, #MicroLEDFlightPhase, #DieLevelInspection, #MicroLEDDisplays, #DisplayManufacturing
About this talk
→ Revolutionizing µLED Production with Laser-Based Processes · René Liebers · MicroLED Connect 2024
Other talks by René Liebers
- Laser cutting for separating waveguides for AR devices · Printed Electronics Innovation Day | Winter 2024
More highlights from René Liebers
- ▶ Why is substrate bending strength the ultimate gatekeeper for augmented reality waveguide mass production? · Printed Electronics Innovation Day 2024
- ▶ How does dual-wavelength laser filamentation solve the challenge of chipping in high-index waveguide dicing? · Printed Electronics Innovation Day 2024
- ▶ Did you know that optimizing front-side laser cutting strength actually degrades the backside edge strength of your glass? · Printed Electronics Innovation Day 2024
