Rolf Meyerhans | Norbert Schläfli: Can a slot-die be repositioned to one-micron edge accuracy regardless of its 50–300 mm width?
08:16 - 09:46
Other snippets from this talk
Summary of the clip:
Can a slot-die be repositioned to one-micron edge accuracy regardless of its 50–300 mm width?
The platform includes a heated slot-die system with cooling capacity, so the die can be held at the right thermal behavior. Operators identified slot-die positioning as a key issue. The designed positioning system applies the same settings and the same force to place the slot-die at different positions.
To avoid backlash, the system compensates force against gravity so the axis sees consistent forces. That supports accurate positioning. Positioning in tilt is calculated in real time, giving one-micron steps at the die edge. The result is intended to be independent of die width.
The stated result is one micron in the corner whether the die is 300 millimetres or 50 millimetres wide. Different dies can therefore use the same settings. This addresses the operator request for repeatable slot-die placement across positions, with real-time tilt calculation and force compensation supporting edge accuracy.
In this short video, you can learn:
* A heated slot-die system with cooling capacity is part of the platform.
* Force against gravity is compensated to keep axis forces consistent and avoid backlash.
* Real-time tilt calculation gives one-micron edge steps for both 50 mm and 300 mm dies.
📋 **Clip Abstract** The clip describes a slot-die positioning approach using a heated, cooled die, force compensation against gravity, and real-time tilt calculation. It reports one-micron edge positioning in the corner for dies from 50 mm to 300 mm, with the same settings across different dies.
About the speaker:
* Speaker: Rolf Meyerhans
* Company: Norbert Schläfli
* Event: Electronics RESHAPED 2026 | Berlin
* Location: Estrel, Berlin
USA: The Future of Electronics RESHAPED | USA
📅 Save the date: 9 and 10 June 2027
📍 Mountain View, California (Silicon Valley)
📋 Info: https://www.techblick.com/electronicsreshapedusa
Europe
The Future of Electronics RESHAPED | Berlin
📅 Save the date: 20 and 21 October 2027
📍 Berlin, Germany
📋 Info: https://www.techblick.com/electronicsreshaped
#SlotDiePositioning, #HeatedSlotDie, #ForceCompensation, #MicronEdgeAccuracy, #PrintedElectronics, #PerovskiteSolarCells
This is a highlight of the presentation:
Development of a Modular Roll-to-Roll Research Platform for Perovskite Solar Cells
More Highlights from the same talk.
03:11 - 04:43
How do you hold identical web tension across two slot-die stations without touching the coated web?
How do you hold identical web tension across two slot-die stations without touching the coated web?
The platform's web path runs two slot-die coating stations, followed by a nitrogen knife and hot plate, with a rewinding and splice-support-tape module. It can run bi-directionally, left-to-right and right-to-left, and holds web tension conditions while operating in a humidity-reduced atmosphere of about 5% air humidity around the coating compartments.
Between the first and second slot-die, an air deflection roller keeps the web out of contact. A nitrogen cushion sits between the substrate and that air deflection roller. Web-tension information is fed back so that the right tension is held between slot-dies one and two, preserving the substrate condition from the first to the second coating station.
The design includes drying capacity and a module for rewinding and splicing support tapes into the system. The web path pairs the two coating stations with a nitrogen knife and hot plate, and the machine is bi-directional. The air deflection roller and nitrogen cushion allow non-contact transport between the two slot-die stations under controlled tension.
In this short video, you can learn:
* An air deflection roller with a nitrogen cushion provides non-contact web transport between the first and second slot-die stations.
* Web-tension information is used to maintain the right tension between slot-dies one and two and preserve substrate condition.
* The platform runs bi-directionally in about 5% air humidity around the coating compartments, with a nitrogen knife, hot plate, drying capacity and a rewinding/splice-support-tape module.
📋 **Clip Abstract** A modular roll-to-roll research platform carries two slot-die coating stations with a nitrogen knife, hot plate, drying capacity and a rewinding and splice-support-tape module. Between the two slot-dies, an air deflection roller and nitrogen cushion enable non-contact web transport, with web-tension information used to hold the right tension and run bi-directionally in about 5% air humidity around the coating compartments.
About the speaker:
* Speaker: Rolf Meyerhans
* Company: Norbert Schläfli
* Event: Electronics RESHAPED 2026 | Berlin
* Location: Estrel, Berlin
USA: The Future of Electronics RESHAPED | USA
📅 Save the date: 9 and 10 June 2027
📍 Mountain View, California (Silicon Valley)
📋 Info: https://www.techblick.com/electronicsreshapedusa
Europe
The Future of Electronics RESHAPED | Berlin
📅 Save the date: 20 and 21 October 2027
📍 Berlin, Germany
📋 Info: https://www.techblick.com/electronicsreshaped
#SlotDieCoating, #AirDeflectionRoller, #NitrogenCushion, #WebTensionControl, #RollToRollProcessing, #PerovskiteSolarCells
18:51 - 20:43
How do you keep a scratch-sensitive coated web on track without letting it touch rollers?
How do you keep a scratch-sensitive coated web on track without letting it touch rollers?
For scratch-sensitive optical devices, every roller is a potential contact point. The coated surface is kept on the backside of the substrate; where contact with the coated surface is unavoidable, a microprocess roller is used, and an air cushion prevents contact to that roller. Pressure and volume control the cushion.
Web tension is inferred from the reaction force measured between the rollers and the air cushion, so too much or too little tension is known. A complete web-tension measurement system and low-friction tensor units compensate for unroundness of the main substrate roll, preventing tension variation from roller or substrate-roll unroundness.
During the coating process, the web tension is measured and documented, giving a record of how tension behaved. This keeps the scratch-sensitive coated web under control while the platform handles the optical device. The documentation covers the web tension during coating.
In this short video, you can learn:
* An air cushion around a microprocess roller prevents contact with the coated surface, with pressure and volume keeping the cushion controlled.
* Reaction-force measurement between the rollers and the air cushion provides web-tension information, flagging too much or too little tension.
* Low-friction tensor units compensate substrate-roll unroundness, and web tension is measured and documented during coating.
📋 **Clip Abstract** The approach keeps the coated surface on the backside of the substrate and uses an air cushion around a microprocess roller to avoid contact with the coated surface. Web tension is inferred from reaction force, controlled with low-friction tensor units and documented during coating.
About the speaker:
* Speaker: Rolf Meyerhans
* Company: Norbert Schläfli
* Event: Electronics RESHAPED 2026 | Berlin
* Location: Estrel, Berlin
USA: The Future of Electronics RESHAPED | USA
📅 Save the date: 9 and 10 June 2027
📍 Mountain View, California (Silicon Valley)
📋 Info: https://www.techblick.com/electronicsreshapedusa
Europe
The Future of Electronics RESHAPED | Berlin
📅 Save the date: 20 and 21 October 2027
📍 Berlin, Germany
📋 Info: https://www.techblick.com/electronicsreshaped
#AirCushionRoller, #WebTensionMeasurement, #MicroprocessRoller, #LowFrictionTensorUnits, #RollToRollProcessing, #PrintedElectronics
10:19 - 11:31
How do you tune nitrogen quenching position and flow as coating speed changes?
How do you tune nitrogen quenching position and flow as coating speed changes?
The quenching hardware is a volume- and mass-controlled nitrogen knife, so the amount of nitrogen and the applied pressure come straight from the recipe rather than from operator judgement. Both parameters are therefore recipe set points, which is what makes the quench reproducible from run to run.
The knife moves around the coating line, so the distance from the slot die to the nitrogen knife is a free variable. It must be re-set as coating speed changes, because the interval between wet-film deposition and nitrogen exposure shifts with line speed.
Everything is automated for fast changeover, so quench position and knife distance can be changed without manual re-rigging. The platform also integrates traditional printing units — radio printing and flexo printing — so the nitrogen knife sits inside a modular roll-to-roll research line rather than a dedicated single-purpose coater.
In this short video, you can learn:
* Nitrogen amount and pressure are volume- and mass-controlled, taken from the recipe rather than set by hand.
* Slot-die-to-knife distance is repositioned according to coating speed to hold the quench in the right place.
* Knife movement is automated for fast changeover, and the same platform also carries radio and flexo printing units.
📋 **Clip Abstract** Quench gas amount and pressure are volume- and mass-controlled by a nitrogen knife whose position travels along the coating line. Because the slot-die-to-quench distance depends on how fast the film is coated, positioning is automated for fast changeover inside a modular roll-to-roll platform.
About the speaker:
* Speaker: Rolf Meyerhans
* Company: Norbert Schläfli
* Event: Electronics RESHAPED 2026 | Berlin
* Location: Estrel, Berlin
USA: The Future of Electronics RESHAPED | USA
📅 Save the date: 9 and 10 June 2027
📍 Mountain View, California (Silicon Valley)
📋 Info: https://www.techblick.com/electronicsreshapedusa
Europe
The Future of Electronics RESHAPED | Berlin
📅 Save the date: 20 and 21 October 2027
📍 Berlin, Germany
📋 Info: https://www.techblick.com/electronicsreshaped
#NitrogenKnife, #SlotDieCoating, #PerovskiteQuenching, #RollToRollCoating, #PerovskiteSolarCells, #PrintedElectronics
About this talk
→ Development of a Modular Roll-to-Roll Research Platform for Perovskite Solar Cells · Rolf Meyerhans · The Future of Electronics RESHAPED 2026 Berlin
Other talks by Rolf Meyerhans
- Highly Scaled Gravure Printing · Innovations Festival: Printed, Flexible, Hybrid, 3D, Wearable, & Textile Electronics 2023
- Highly Scaled Gravure Printing · CPES | Canadian Printable Electronics Symposium 2023


