Seogsoon Kim | UniJet: Which ink properties—viscosity, boiling point, polarity—decide whether a perovskite inkjet process works?
08:33 - 10:19
Other snippets from this talk
Summary of the clip:
Which ink properties—viscosity, boiling point, polarity—decide whether a perovskite inkjet process works?
The absorber layer starts with jetting property. Viscosity and surface tension must be matched, while boiling point and vapor pressure govern nozzle clogging and drying characteristic. The polarity index is also important, which is why DMF, DMSO and MP solution are used. These are not chosen simply for good drying, nor for drying at a low rate: the process sits on a trade-off between the two drying characteristics.
Control is not always straightforward: it is described as not difficult, but sometimes very difficult to control. Some factors cannot be controlled by inkjet itself, while the system can control others. Maintenance schedules are therefore set according to the ink property to eliminate clogging. With this approach, the team reports successfully getting the perovskite absorber layer.
Drying is critical for the perovskite absorber layer, and not only for inkjet. The talk stresses that up to drying is very important, and that drying seems to be more important. Earlier, a multi-SEM concept improved coverage and also improved PCE. That combination ties absorber-layer formation and drying to coverage and PCE improvements.
In this short video, you can learn:
* Jetting requires matched viscosity and surface tension, plus boiling point and vapor pressure chosen for nozzle clogging and drying behavior.
* Polarity index is why DMF, DMSO and MP solution are used, with drying caught in a trade-off rather than simply fast or slow.
* Ink-property-based maintenance schedules eliminate clogging, and drying is emphasized as critical beyond the inkjet step itself.
📋 **Clip Abstract** Inkjet perovskite absorber layers depend on matched viscosity and surface tension, with boiling point, vapor pressure and polarity index setting clogging and drying behavior. DMF, DMSO and MP solution are used, maintenance follows ink properties, and drying is stressed as critical for the absorber layer and for coverage and PCE improvement.
About the speaker:
* Speaker: Seogsoon Kim
* Company: UniJet
* Event: Perovskite Connect 2026 | Berlin
* Location: Estrel, Berlin
Save the date: Perovskite Connect 2027 | 20 and 21 OCT 2027 | Berlin
Co-located with the Future of Electronics RESHAPED conference and exhibition
Learn more: https://www.techblick.com/perovskiteconnect
Intestered in exhibiting: learn more here: https://www.techblick.com/perovskiteconnect
#PerovskiteAbsorberLayer, #InkjetJettingProperty, #NozzleClogging, #PolarityIndex, #PerovskiteSolarCells, #Photovoltaics
This is a highlight of the presentation:
Inkjet Printing Technology for Perovskite/Si Solar Cell
21 and 22 OCT 2026
Estrel, Berlin
Organised By:
More Highlights from the same talk.
04:03 - 06:28
Does inkjet beat slot die on PCE uniformity, throughput and cost—and by how much?
Does inkjet beat slot die on PCE uniformity, throughput and cost—and by how much?
Thickness uniformity is presented as a major inkjet advantage, and that thickness uniformity generates PCE uniformity. Inkjet is described as more uniform than slot die; customers who first develop slot die and are not successful move to inkjet and get a successful result. This uniformity link is the basis for comparing the two deposition approaches.
Productivity is another stated advantage: inkjet can print up to 635 millimeters per second, described as very high compared with slot die. For tandem solar cells with a 200 by 200 size, inkjet is said to be much faster than slot die. Overall cost is also lower than slot die.
After EU PVSEC, the slide reports slot die deposition PCE variation over 3%, while inkjet deposition is less than 1%. Better results are possible with perovskite only; including tandem solar cell introduces a little difference. The work applies this to SEM and perovskite absorber layers with many partners.
In this short video, you can learn:
* Inkjet deposition is stated to be more uniform than slot die, and thickness uniformity generates PCE uniformity.
* Inkjet can print up to 635 millimeters per second and is described as faster and lower cost than slot die, including for 200 by 200 tandem cells.
* Slot die PCE variation is over 3% versus less than 1% for inkjet, though tandem inclusion introduces a little difference.
📋 **Clip Abstract** The clip compares inkjet and slot die for perovskite and tandem solar cells on uniformity, throughput and cost. It reports inkjet thickness and PCE uniformity advantages, up to 635 millimeters per second, lower overall cost, and less than 1% PCE variation versus over 3% for slot die, with a small tandem caveat.
About the speaker:
* Speaker: Seogsoon Kim
* Company: UniJet
* Event: Perovskite Connect 2026 | Berlin
* Location: Estrel, Berlin
Save the date: Perovskite Connect 2027 | 20 and 21 OCT 2027 | Berlin
Co-located with the Future of Electronics RESHAPED conference and exhibition
Learn more: https://www.techblick.com/perovskiteconnect
Intestered in exhibiting: learn more here: https://www.techblick.com/perovskiteconnect
#InkjetDeposition, #SlotDieDeposition, #ThicknessUniformity, #PCEVariation, #PerovskiteSolarCells, #SolarCellManufacturing
14:38 - 16:27
Can a 4,000 wafer/hour inkjet line hit 50–100 µm etch-gap uniformity and run operator-free?
Can a 4,000 wafer/hour inkjet line hit 50–100 µm etch-gap uniformity and run operator-free?
TandemJet 4,000 is an inkjet printer in development, scheduled for release next February, with an initial version shown next month in Korea. Its target is 4,000 wafers per hour with etch gap uniformity below 50 to 100 microns. UniJet’s fiber-optic inkjet driver and controller are named as the means to achieve that target.
Drying and annealing are described as very important. The line applies hybrid drying using VCD, air blow, gas censure and NIR. These are listed as hybrid drying elements; the clip does not explain each module’s individual role. They sit alongside the inkjet driver and controller in the TandemJet 4,000 line.
The line is being developed operator-free. Input parameters and output results are measured and controlled with machine learning and AI. Grain size measurement and sequence measurement can be fed back to the AI, which learns from those results and automatically adjusts input parameters. The final target is application-dependent: perovskite absorber inkjet and same inkjet are described as totally different.
In this short video, you can learn:
* TandemJet 4,000 targets 4,000 wafers per hour with etch gap uniformity below 50 to 100 microns, using UniJet’s fiber-optic inkjet driver and controller.
* Hybrid drying and annealing combine VCD, air blow, gas censure and NIR in the developing line.
* The operator-free target uses machine learning and AI to feed back grain size and sequence measurements and automatically adjust input parameters.
📋 **Clip Abstract** UniJet is developing TandemJet 4,000 for perovskite absorber inkjet, targeting 4,000 wafers per hour with etch gap uniformity below 50 to 100 microns using its fiber-optic driver and controller. The line combines VCD, air blow, gas censure and NIR hybrid drying and annealing with an operator-free machine-learning/AI control target that feeds back grain size and sequence measurements to adjust input parameters.
About the speaker:
* Speaker: Seogsoon Kim
* Company: UniJet
* Event: Perovskite Connect 2026 | Berlin
* Location: Estrel, Berlin
Save the date: Perovskite Connect 2027 | 20 and 21 OCT 2027 | Berlin
Co-located with the Future of Electronics RESHAPED conference and exhibition
Learn more: https://www.techblick.com/perovskiteconnect
Intestered in exhibiting: learn more here: https://www.techblick.com/perovskiteconnect
#TandemJet4000, #FiberOpticInkjet, #HybridVCDNIR, #EtchGapUniformity, #PerovskiteTandem, #SolarCellManufacturing
10:12 - 11:47
Why is drying more important than inkjet printing for the perovskite absorber, and why does one drying method fail?
Why is drying more important than inkjet printing for the perovskite absorber, and why does one drying method fail?
Inkjet printing is already uniform enough; the decisive step for the perovskite absorber layer is drying, which makes a totally different result. Many drying methods are applied — VCD, air blow, gas censure, hot plate and IR — and hybrid drying is recommended to achieve the best result. Drying combines two processes: nucleation and crystallization.
Nucleation requires eliminating solvent as quickly as possible, which generates fast nucleation. Then crystallization begins continuously and must be given enough time. To meet both requirements — rapid solvent removal and sufficient crystallization time — one drying method is not enough, which is why the focus is on developing hybrid drying.
Nucleation means solvent must be eliminated as quickly as possible to generate fast nucleation; crystallization then needs enough time. Because both requirements must be met, one drying method is not enough. Hybrid drying draws on methods including VCD, air blow, gas censure, hot plate and IR to achieve the best result.
In this short video, you can learn:
* Inkjet printing is already uniform enough; drying is the step that makes a totally different result for the perovskite absorber layer.
* Drying combines nucleation, where solvent is eliminated as quickly as possible, with crystallization, which needs enough time.
* Because one drying method cannot meet both requirements, hybrid drying — VCD, air blow, gas censure, hot plate and IR — is recommended to achieve the best result.
📋 **Clip Abstract** Inkjet printing is already uniform enough, so drying becomes the more important step for the perovskite absorber layer because it makes a totally different result. Drying combines fast solvent elimination for nucleation with sufficient time for crystallization, and because one method cannot meet both requirements, hybrid drying using VCD, air blow, gas censure, hot plate and IR is recommended.
About the speaker:
* Speaker: Seogsoon Kim
* Company: UniJet
* Event: Perovskite Connect 2026 | Berlin
* Location: Estrel, Berlin
Save the date: Perovskite Connect 2027 | 20 and 21 OCT 2027 | Berlin
Co-located with the Future of Electronics RESHAPED conference and exhibition
Learn more: https://www.techblick.com/perovskiteconnect
Intestered in exhibiting: learn more here: https://www.techblick.com/perovskiteconnect
#PerovskiteAbsorberDrying, #HybridDrying, #NucleationCrystallization, #VCDAirBlowIR, #PerovskiteSolarCells, #ThinFilmPhotovoltaics
About this talk
→ Inkjet Printing Technology for Perovskite/Si Solar Cell · Seogsoon Kim · Perovskite Connect 2026


