top of page

Simon Nieh

Front Edge Technology

* All members of the platform can watch the entire presentation.

 

Please register to become a member.

Simon Nieh | Front Edge Technology: Why does uncontrolled lithium plating grow into 10–20 µm rods and leave only 30% charge efficiency?

03:45 - 05:45

Other snippets from this talk

Summary of the clip:

Why does uncontrolled lithium plating grow into 10–20 µm rods and leave only 30% charge efficiency?

The baseline cell is a plan-view SEM sample: 40 µm lithium cobalt oxide cathode, 3 µm LiPO electrolyte, 10 nm metal, delivering about 2.2 millliamp-hour per square centimeter fully charged. Charging only 0.02% of capacity — microamp-hours — already shows non-uniform lithium nucleation at preferential sites. White dots appear along cathode grain boundaries; the amorphous electrolyte is uniform, so the contrast maps the cathode surface.

Continue to full charge without control and the lithium surface becomes very rough. Deposits grow to a few microns in diameter and 10–20 microns long — long rods, not a dense film. Since the electrolyte is amorphous and uniform, the surface contrast reflects the cathode surface, so the growth habit tracks features inherited from the cathode rather than electrolyte texture.

Even after discharge to cutoff, a large amount of lithium remains trapped on the surface. In this uncontrolled case charge efficiency is on the order of 30%: most of the lithium stays on the surface and, in subsequent cycles, cannot participate or contribute to capacity. That is the direct cost of uncontrolled plating on a solid-state cell.

In this short video, you can learn:
* Lithium nucleation begins within the first 0.02% of charge, appearing as white dots preferentially along cathode grain boundaries.
* Uncontrolled growth produces rough deposits a few microns wide and 10–20 microns long rather than a uniform lithium film.
* Lithium trapped on the surface after discharge cutoff leaves charge efficiency around 30%, with the remainder unable to contribute in later cycles.

📋 **Clip Abstract** A 40 µm lithium cobalt oxide / 3 µm LiPO / 10 nm metal solid-state cell shows non-uniform lithium nucleation within 0.02% of charge, starting preferentially at cathode grain boundaries. Uncontrolled charging grows 10–20 µm rods and traps lithium that survives discharge cutoff, leaving charge efficiency around 30%.

About the speaker:
* Speaker: Simon Nieh
* Company: Front Edge Technology
* Event: Solid-State Batteries: Innovations, Promising Start-ups, Future Roadmap
* Location: Online

Join TechBlick to learn about the state of the art in solid state batteries, Si anode, advanced cathodes, sodium batteries, and beyond
https://www.techblick.com/

#LithiumPlating, #GrainBoundaryNucleation, #LithiumCobaltOxide, #ChargeEfficiency, #SolidStateBatteries, #LithiumMetalAnodes

This is a highlight of the presentation:

Cathode and anode considerations in the development of all solid-state Lithium battery

Solid-State Batteries: Innovations, Promising Start-ups, Future Roadmap

Battery Materials: Next-Gen & Beyond Lithium Ion

9-10 February 2022

Online

Organised By:

TechBlick

TechBlick

More Highlights from the same talk.

12:29 - 14:52

Can a pure cathode material reach 300 Wh/kg in an all-solid-state cell?

Can a pure cathode material reach 300 Wh/kg in an all-solid-state cell?

Using only electrolyte and cathode weight, a 20-micron LLZO plate with traditional lithium cobalt oxide needs a minimum 26-micron cathode to reach 300 Wh/kg. That ideal case neglects the current collector, sealing material and anode capacity loss. At 26 microns, the cathode delivers 1.8 milliamp-hours per square centimeter.

Considering all other parameters, the real cathode thickness is way more than 30 microns. With a higher-capacity cathode such as AMC and the same 20-micron LLZO, about 16 microns of MC811 is needed. Adding other battery elements or capacity-loss mechanisms, the cathode must be way below 20 microns.

LiFePO4 carries a pretty big weight penalty. If thickness is reduced to 10 microns, the minimum is still 8 microns, and very likely more than 10 microns are needed. This pretty much rules out using a pure cathode material for these 300 Wh/kg solid-state batteries.

In this short video, you can learn:
* A 26-micron lithium cobalt oxide cathode paired with 20-micron LLZO reaches 300 Wh/kg only in an idealized calculation that ignores current collector, sealing and anode capacity loss.
* With AMC-type cathode material, 20-micron LLZO requires about 16 microns of MC811, but real cell elements and capacity loss push the required thickness way below 20 microns.
* LiFePO4’s thickness floor of 8 microns, likely more than 10 microns, rules out a pure cathode material for these 300 Wh/kg solid-state batteries.

📋 **Clip Abstract** The clip calculates cathode thickness limits for 300 Wh/kg all-solid-state cells using 20-micron LLZO. It shows that traditional lithium cobalt oxide, AMC/MC811 and LiFePO4 cathodes cannot be used as pure cathode materials once realistic cell elements and capacity-loss mechanisms are included.

About the speaker:
* Speaker: Simon Nieh
* Company: Front Edge Technology
* Event: Solid-State Batteries: Innovations, Promising Start-ups, Future Roadmap
* Location: Online

Join TechBlick to learn about the state of the art in solid state batteries, Si anode, advanced cathodes, sodium batteries, and beyond
https://www.techblick.com/

#LLZOElectrolyte, #CathodeThickness, #MC811, #ArealCapacity, #SolidStateBatteries, #EnergyDensity

06:52 - 08:32

At low lithium diffusion, how much of a 25 µm LCO cathode capacity is actually discharged before cutoff?

At low lithium diffusion, how much of a 25 µm LCO cathode capacity is actually discharged before cutoff?

The cathode example starts with a 25-micron lithium cobalt oxide electrode charged to 4.2 volts, giving about 1.93 milliamp-hours per square centimeter. A roughly 5-hour discharge corresponds to 0.4 milliamps per square centimeter, with discharge cut off at 3 volts. The calculation plots lithium distribution across a 20-micron thick lithium cobalt oxide layer, simplifying by using a constant diffusion coefficient even though it changes with lithium concentration.

At a lithium diffusion coefficient of 1e-11 square centimeters per second, the surface lithium concentration quickly reaches 1. The battery open-circuit voltage reaches 3 volts and discharge is cut off, leaving only 3% of capacity discharged. Raising the coefficient to 1e-10 square centimeters per second increases discharged capacity to 18%, showing how strongly cathode utilization depends on lithium transport.

The progression continues to 5e-10 square centimeters per second, where 70% of capacity is discharged. The case then moves to 1e-9 square centimeters per second; the presentation excerpt ends at that value without stating the discharged capacity. The comparison makes cathode thickness, discharge rate, cutoff voltage and diffusion coefficient inseparable: a slower coefficient strands usable lithium cobalt oxide capacity before the 3-volt cutoff.

In this short video, you can learn:
* For a 25-micron cathode charged to 4.2 volts, the example gives about 1.93 milliamp-hours per square centimeter and uses 0.4 milliamps per square centimeter for a roughly 5-hour discharge.
* With a constant lithium diffusion coefficient of 1e-11 square centimeters per second, surface concentration reaches 1, OCV hits 3 volts, and only 3% of capacity is discharged.
* Increasing the coefficient to 1e-10 and 5e-10 raises discharged capacity to 18% and 70%, respectively, while the excerpt reaches 1e-9 without giving its result.

📋 **Clip Abstract** A 25-micron lithium cobalt oxide cathode charged to 4.2 volts provides about 1.93 milliamp-hours per square centimeter, evaluated at 0.4 milliamps per square centimeter and a 3-volt cutoff. Constant diffusion coefficients from 1e-11 to 5e-10 square centimeters per second show only 3%, 18% and 70% discharged capacity, before the excerpt reaches 1e-9.

About the speaker:
* Speaker: Simon Nieh
* Company: Front Edge Technology
* Event: Solid-State Batteries: Innovations, Promising Start-ups, Future Roadmap
* Location: Online

Join TechBlick to learn about the state of the art in solid state batteries, Si anode, advanced cathodes, sodium batteries, and beyond
https://www.techblick.com/

#LCOCathode, #LithiumDiffusion, #CapacityUtilization, #ThreeVoltCutoff, #SolidStateBatteries, #BatteryMaterials


About this talk

→ Cathode and anode considerations in the development of all solid-state Lithium battery · Simon Nieh · Battery Materials: Next-Gen & Beyond Lithium Ion 2022

More Snippets
CONTACT US

KGH Concepts GmbH

Mergenthalerallee 73-75, 65760, Eschborn

+49 17661704139

admin@techblick.com

TechBlick is owned and operated by KGH Concepts GmbH

Registration number HRB 121362

VAT number: DE 337022439

  • LinkedIn
  • YouTube

Sign up for our newsletter to receive updates on our latest speakers and events AND to receive analyst-written summaries of the key talks and happenings in our events.

Thanks for submitting!

© 2026 by KGH Concepts GmbH

bottom of page