Simon Rihm | Notion Systems: How many process steps can additive inkjet eliminate from one functional layer?
03:40 - 05:23
Other snippets from this talk
Summary of the clip:
How many process steps can additive inkjet eliminate from one functional layer?
In the subtractive baseline, producing one functional layer takes six steps: apply the functional layer, apply resist, expose resist, develop resist, etch the layer, and strip the resist. The substrate is the starting point. That sequence is described as a lot of steps and motivates comparing it with additive manufacturing.
Moving from subtractive to additive can remove the subtractive process; in the example, the route goes to step four. Going further, the functional layer itself can be printed directly as the sixth step. Additive manufacturing produces that layer in one single producing step instead.
The stated advantage is reduced process steps. Because of that reduction, faster turnaround is also cited as a consequence. The concrete comparison in the clip is one single functional layer, where direct additive printing replaces the multi-step subtractive sequence.
In this short video, you can learn:
* The subtractive example uses six producing steps to create one functional layer.
* Additive manufacturing can print the functional layer directly in one single producing step.
* Reduced process steps are cited as an advantage that also enables faster turnaround.
π **Clip Abstract** A subtractive flow for one functional layer is broken down into six producing steps, from functional-layer application through resist processing and etch to resist strip. Direct additive printing is contrasted as a one-step route to the functional layer, with reduced process steps linked to faster turnaround.
About the speaker:
* Speaker: Simon Rihm
* Company: Notion Systems
* Event: Electronics RESHAPED 2026 | Berlin
* Location: Estrel, Berlin
USA: The Future of Electronics RESHAPED | USA
π
Save the date: 9 and 10 June 2027
π Mountain View, California (Silicon Valley)
π Info: https://www.techblick.com/electronicsreshapedusa
Europe
The Future of Electronics RESHAPED | Berlin
π
Save the date: 20 and 21 October 2027
π Berlin, Germany
π Info: https://www.techblick.com/electronicsreshaped
#SubtractiveProcess, #AdditiveManufacturing, #FunctionalLayer, #ReducedProcessSteps, #PrintedElectronics, #InkjetPrinting
This is a highlight of the presentation:
Enabling Sustainable Electronics Manufacturing through Additive Functional Inkjet Printing
More Highlights from the same talk.
02:33 - 04:33
Printing the functional layer directly eliminates how many of the six standard subtractive process steps?
Printing the functional layer directly eliminates how many of the six standard subtractive process steps?
The conventional subtractive route starts with a substrate and applies the functional layer across the entire surface. It then adds resist, exposes the resist, develops it, etches the functional layer, and finally strips the resist. In this example, creating just one needed functional layer consumes six production steps, driving a fairly high investment in time and resources.
Introducing additive manufacturing changes that sequence for two applications. In the top process, the goal is to print or create the etch resist layer directly. Printing that etch resist directly avoids two process steps. In the bottom process, the goal is to print the functional layer itself, which skips five prior steps and leaves only one production step.
The comparison is simple: direct printing of the functional layer reduces the six-step subtractive example to a single production step. Direct printing of the etch resist removes two steps instead. This illustrates how additive methods reduce production steps and, by extension, the time and resource investment required to create needed functional layers.
In this short video, you can learn:
* A conventional subtractive flow for one functional layer uses six steps: functional layer, resist apply, expose, develop, etch, strip.
* Printing the etch resist directly avoids two of those process steps.
* Printing the functional layer itself skips five prior steps, leaving only one production step.
π **Clip Abstract** The clip contrasts a six-step subtractive process for creating one functional layer with additive alternatives. Printing the etch resist directly removes two steps, while printing the functional layer itself skips five prior steps and reduces production to a single step.
About the speaker:
* Speaker: Simon Rihm
* Company: Notion Systems
* Event: nnovation Festival: Additive, Printed, Sustainable Electronics, MicroLEDs and AR/VR Displays, Perovskites | July 2026
* Location: Online Platform
Annual access to our onsite event(s), all online events and a library featuring over 1800 presentations (recordings + PDF) across all our onsite and onsite events and technology areas. Join us and over 2000 members from around the world now.
Explore and join now --> https://www.techblick.com/
#EtchResistPrinting, #FunctionalLayerPrinting, #SubtractiveEtch, #ProcessStepReduction, #PrintedElectronics, #AdditiveElectronics
06:08 - 07:43
Where does additive inkjet actually cut cost, energy and hazardous chemicals in electronics manufacturing?
Where does additive inkjet actually cut cost, energy and hazardous chemicals in electronics manufacturing?
Cost savings come primarily from reduced material waste. Because functional inkjet places material only where it is needed on the substrate, there is no subsequent removal step. Eliminating screens and masks also lowers the cost of the required equipment. This is the first commercial argument for additive deposition.
Sustainability improves through fewer production steps and less material waste, which lowers overall energy consumption. The transcript links these reductions directly to additive manufacturing rather than to downstream abatement. Traditional processes also use chemicals for cleaning and processing that can be hazardous and harmful to the environment; additive manufacturing can reduce the need for those chemicals.
The final benefit is higher flexibility and customization. That matters because additive functional inkjet is not only a waste-reduction story; it changes what can be produced without screens or masks. The combined case is reduced energy, reduced material waste and greater customization for additive manufacturing in electronics.
In this short video, you can learn:
* Depositing ink only where needed removes the material-removal step and cuts waste.
* Eliminating screens and masks lowers equipment cost as well as material use.
* Fewer process steps and less waste reduce energy, and additive methods can cut hazardous cleaning and processing chemicals.
π **Clip Abstract** The clip sets out where additive functional inkjet saves cost, energy and chemicals: material is deposited only where needed, screens and masks are eliminated, and production steps are reduced. It also notes that traditional cleaning and processing chemicals can be hazardous, while additive manufacturing can reduce the need for them and add flexibility and customization.
About the speaker:
* Speaker: Simon Rihm
* Company: Notion Systems
* Event: Electronics RESHAPED 2026 | Berlin
* Location: Estrel, Berlin
USA: The Future of Electronics RESHAPED | USA
π
Save the date: 9 and 10 June 2027
π Mountain View, California (Silicon Valley)
π Info: https://www.techblick.com/electronicsreshapedusa
Europe
The Future of Electronics RESHAPED | Berlin
π
Save the date: 20 and 21 October 2027
π Berlin, Germany
π Info: https://www.techblick.com/electronicsreshaped
#FunctionalInkjet, #MasklessDeposition, #MaterialWasteReduction, #LowEnergyManufacturing, #AdditiveElectronics, #SustainableElectronics
05:20 - 07:00
Can inkjet match subtractive-method throughput, and at what droplet rate per nozzle?
Can inkjet match subtractive-method throughput, and at what droplet rate per nozzle?
At the core of these systems is inkjet: ejecting super-small droplets of fluid from a jetting nozzle, measured in picoliters. The claimed speed is up to 100,000 droplets per second per nozzle, which reframes productivity not as a single-nozzle limit but as a rate multiplied across the head.
The second lever is parallelism: printing is not done with a single nozzle but with around 10,000 per print unit. That combination β 100,000 droplets per second per nozzle across roughly 10,000 nozzles β is the throughput argument for matching subtractive production methods.
Two further properties separate it from subtractive flows. Inkjet is touchless: the printing unit and the substrate never come into contact during the whole printing process. And it is digital, so at any time you decide when, where and whether a drop is generated. That is the material-efficiency and reconfiguration case.
In this short video, you can learn:
* Inkjet ejects picoliter droplets, with up to 100,000 droplets per second generated per single nozzle.
* Throughput scales through parallelism: around 10,000 nozzles are used per print unit rather than a single jet.
* Because the process is touchless and digital, drop placement is decided at any time, in any position, or not at all.
π **Clip Abstract** Inkjet productivity rests on three properties: picoliter droplets fired at up to 100,000 per second per nozzle, around 10,000 nozzles per print unit for parallelism, and a touchless, digital process. Digital control means the drop is generated β or withheld β at any time and position, which is the basis for comparing additive output against subtractive production.
About the speaker:
* Speaker: Simon Rihm
* Company: Notion Systems
* Event: nnovation Festival: Additive, Printed, Sustainable Electronics, MicroLEDs and AR/VR Displays, Perovskites | July 2026
* Location: Online Platform
Annual access to our onsite event(s), all online events and a library featuring over 1800 presentations (recordings + PDF) across all our onsite and onsite events and technology areas. Join us and over 2000 members from around the world now.
Explore and join now --> https://www.techblick.com/
#InkjetPrinting, #PicoliterDroplets, #PrintheadNozzles, #TouchlessDeposition, #AdditiveElectronics, #PrintedElectronics
About this talk
β Enabling Sustainable Electronics Manufacturing through Additive Functional Inkjet Printing Β· Simon Rihm Β· The Future of Electronics RESHAPED 2026 Berlin
Other talks by Simon Rihm
- From Subtractive to Additive: The impact of additive manufacturing on electronics production Β· TechBlick Innovations Festival July 2026
- From Subtractive to Additive: Shaping the Future of R&D with the new n.jet evo Β· Electronics RESHAPED USA 2026
- High-Resolution, High-Impact: EHD Printing for Advanced Electronics Β· Additive, Printed, Hybrid and Sustainable Electronics Innovations Day 2025
More highlights from Simon Rihm
- βΆ Printing the functional layer directly eliminates how many of the six standard subtractive process steps? Β· Innovation Festival: Additive, Printed, Sustainable Electronics
- βΆ Can inkjet match subtractive-method throughput, and at what droplet rate per nozzle? Β· Innovation Festival: Additive, Printed, Sustainable Electronics
- βΆ Can additive manufacturing really replace a 6-step subtractive photolithography process with a single step? Β· Future of Electronics RESHAPED USA 2026
- βΆ How do modern industrial printheads coordinate ten thousand nozzles ejecting 100,000 droplets per second? Β· Future of Electronics RESHAPED USA 2026
- βΆ What happens inside the complex parameter space that dictates successful functional material printing? Β· Future of Electronics RESHAPED USA 2026
- βΆ Your inkjet printer is limited to 20-micron features. How can we print at 5 microns or less for next-gen micro-displays and electronics? Β· Additive, Printed, Hybrid and Sustainable Electronics Innovations Day 2025
- βΆ Why does conventional EHD printing fail on real-world, non-flat surfaces? The secret is a MEMS innovation that decouples drop ejection from flight. Β· Additive, Printed, Hybrid and Sustainable Electronics Innovations Day 2025
- βΆ Is photolithography obsolete? How additive printing can slash 5 process steps into 1 for electronics manufacturing. Β· Additive, Printed, Hybrid and Sustainable Electronics Innovations Day 2025


