top of page

Stefan Hinze

ROWO Coating GmbH

* All members of the platform can watch the entire presentation.

 

Please register to become a member.

Stefan Hinze | ROWO Coating GmbH: How uniform is an 800 mm morpho-color coating, and what electrode roadmap follows?

15:45 - 18:07

Other snippets from this talk

Summary of the clip:

How uniform is an 800 mm morpho-color coating, and what electrode roadmap follows?

For blue and terracotta morpho-color stacks, homogeneity was checked by comparing the blue or terracotta peak position in the spectrum across an 800 mm film width. Because the stack is multilayer, uniformity is difficult, yet the measured peak-position deviation was only 1 to 2% over that width, indicating a quite homogeneous layer stack.

The next step is to move to higher width, up to 1.50 m, through a new project. Morpho-color development will continue on larger width and be integrated into buildings to prove that it works smoothly in an existing building. This scale-up path follows the measured 800 mm uniformity.

Electrode improvement targets very low sheet resistance with very high transmittance, especially for perovskite PV; so far ITO appears to be the only option working on glass and polymer films. Lower sheet resistance is also interesting for OPV. Combining water-vapor barriers with an electrode on top would let a module producer use one film instead of two, reducing cost and weight.

In this short video, you can learn:
* Peak-position deviation across an 800 mm blue and terracotta morpho-color multilayer was only 1 to 2%.
* A new project targets widths up to 1.50 m and building integration for morpho-color coatings.
* Electrode work aims for lower sheet resistance at high transmittance, and a combined water-vapor barrier plus electrode film.

📋 **Clip Abstract** An 800 mm multilayer morpho-color stack showed only 1 to 2% peak-position deviation across the film width for blue and terracotta. The next steps are 1.50 m width and building integration, while electrode development targets lower sheet resistance with high transmittance and a combined barrier-plus-electrode film.

About the speaker:
* Speaker: Stefan Hinze
* Company: ROWO Coating GmbH
* Event: Perovskite Connect 2026 | Berlin
* Location: Estrel, Berlin

Save the date: Perovskite Connect 2027 | 20 and 21 OCT 2027 | Berlin
Co-located with the Future of Electronics RESHAPED conference and exhibition
Learn more: https://www.techblick.com/perovskiteconnect

Intestered in exhibiting: learn more here: https://www.techblick.com/perovskiteconnect

#MorphoColorCoating, #PeakPositionDeviation, #WaterVaporBarrier, #SheetResistance, #PerovskitePV, #OPV

This is a highlight of the presentation:

Roll-to-Roll Solutions for the Energy Transition: Functional Vacuum Coatings for Perovskite and OPV Devices

​

​

21 and 22 OCT 2026

Estrel, Berlin

Organised By:

​

​

More Highlights from the same talk.

06:03 - 08:02

Can a Bragg mirror solve the transmittance–NIR reflectance trade-off in transparent PV electrodes?

Can a Bragg mirror solve the transmittance–NIR reflectance trade-off in transparent PV electrodes?

Starting with the transparent electrode, a standard DMD stack places a silver layer in the middle and delivers high transmittance in the visible range, which matters for transparent OPVs that must be seen through in daylight. Its weakness is near-infrared reflectance: the single silver layer is poor there, so the electrode cannot simultaneously give the visible transparency and NIR response desired.

Adding a second silver layer creates a double-silver design. This gives good near-infrared reflectance, so the organic absorber can absorb that light well, but visible transmittance is quite lower because the silver and other metal layers have high absorption. That NIR gain therefore carries a visible optical penalty, making the double-silver route less ideal for transparent PV, where high daylight transmission is wanted.

The proposed middle way is a Bragg mirror: an additional multilayer placed between the PET plastic and the DMD itself. By fine-tuning that multilayer, the stack can retain very high transmittance in the visual range while also achieving very high near-infrared reflectance. That combination is presented as a really good result for transparent PV electrodes, with morpho color on plastic also noted as a multilayer or ITO single-layer coating option.

In this short video, you can learn:
* A single-silver DMD gives high visible transmittance but poor near-infrared reflectance.
* A double-silver stack improves NIR reflectance but lowers visible transmittance through metal absorption.
* A Bragg mirror multilayer between PET and DMD can combine high visible transmittance with high NIR reflectance.

📋 **Clip Abstract** The clip compares transparent electrode designs for transparent PV and OPV: a single-silver DMD has high visible transmittance but poor near-infrared reflectance, while a double-silver stack improves NIR reflectance at the cost of visible transmittance due to metal absorption. A Bragg mirror added between PET and the DMD is presented as a middle way, fine-tuned to keep high visible transmittance and high NIR reflectance for transparent PV.

About the speaker:
* Speaker: Stefan Hinze
* Company: ROWO Coating GmbH
* Event: Perovskite Connect 2026 | Berlin
* Location: Estrel, Berlin

Save the date: Perovskite Connect 2027 | 20 and 21 OCT 2027 | Berlin
Co-located with the Future of Electronics RESHAPED conference and exhibition
Learn more: https://www.techblick.com/perovskiteconnect

Intestered in exhibiting: learn more here: https://www.techblick.com/perovskiteconnect

#BraggMirror, #DoubleSilverDMD, #NearInfraredReflectance, #TransparentElectrode, #TransparentPV, #OrganicPhotovoltaics

12:19 - 14:19

Can morpho-color interference filters move from glass to plastic while keeping above 90–95% relative efficiency?

Can morpho-color interference filters move from glass to plastic while keeping above 90–95% relative efficiency?

The blue in morpho butterflies comes from an interference filter on the wing surface, not from particles or pigments. Fraunhofer ISE in Freiburg developed this on glass to make colorful PV modules and colorful glass modules that still retain very high efficiency. A project then tried to implement the whole system on a plastic film, targeting lightweight modules, novel solutions and possibly OPV or perovskite cells.

For integration, a standard PV cell on glass allows several routes. The filter can go on the front glass, described as the most difficult solution because of stability. It can be integrated on the solar cell with front glass on top, or for OPVs the glass itself could be removed and the coating applied directly.

Morpho-color technology's key advantage is very high angle stability. Photos of glass modules taken from different angles show quite good color stability. More importantly, efficiency remains high: compared with a standard black module, colored modules still achieve efficiencies above 90% and 95%, even though they are colored.

In this short video, you can learn:
* The morpho blue is an interference filter, not pigment or particles.
* Fraunhofer ISE's glass-based colorful modules retain very high efficiency; the project tried the system on plastic film.
* Colored morpho modules keep above 90–95% relative efficiency versus a black module and show good color stability across angles.

📋 **Clip Abstract** This clip explains how morpho-butterfly interference filters, first developed on glass for colorful high-efficiency PV modules, are being implemented on plastic film. It covers integration routes on front glass or directly on cells and reports very high angle stability with colored modules retaining above 90–95% efficiency versus black.

About the speaker:
* Speaker: Stefan Hinze
* Company: ROWO Coating GmbH
* Event: Perovskite Connect 2026 | Berlin
* Location: Estrel, Berlin

Save the date: Perovskite Connect 2027 | 20 and 21 OCT 2027 | Berlin
Co-located with the Future of Electronics RESHAPED conference and exhibition
Learn more: https://www.techblick.com/perovskiteconnect

Intestered in exhibiting: learn more here: https://www.techblick.com/perovskiteconnect

#MorphoColor, #InterferenceFilter, #ColorfulPV, #PlasticFilmCoating, #PerovskitePV, #OPV

09:32 - 10:49

What PCE and transmission were reported for transparent cells and modules built on these electrodes?

What PCE and transmission were reported for transparent cells and modules built on these electrodes?

The clip reports partner-built initial cells using only electrodes supplied by the coating company. At Forschungszentrum Jülich in Nürnberg, a cell was made with a spectrum on a DMD and a DMD with a BRAG mirror. That combination reached 12% PCE, described as a record, while the cell retained very high transmittance.

Fraunhofer ISE, located close to Freiburg, repeated the work on a larger module measuring 15 by 15 centimetres. The module delivered a somewhat lower efficiency than the Jülich cell, but its transmittance remained very good. At a transmission of 33%, the speaker noted it was almost invisible from one angle and better when viewed straight on.

The presentation frames these results as recent and notable for transparent photovoltaic applications, where visible transmission matters alongside power conversion. The company does not build complete cells itself; its scope is the electrodes, while partners such as Jülich and Fraunhofer ISE fabricate cells and modules. The reported 12% cell PCE and 33% module transmission illustrate that electrode-level work is being validated in partner devices.

In this short video, you can learn:
* A partner-built transparent cell using a DMD with a BRAG mirror reached 12% PCE with very high transmittance, described as a record.
* Fraunhofer ISE's 15 × 15 cm module showed lower efficiency than the cell but achieved 33% transmission.
* The coating company supplies electrodes only, while Jülich and Fraunhofer ISE fabricated the cells and modules.

📋 **Clip Abstract** Partner cells built on the supplied electrodes reached 12% PCE at high transmittance, described as a record, using a DMD with a BRAG mirror. A larger 15 × 15 cm Fraunhofer ISE module showed lower efficiency but 33% transmission, which the speaker called very good.

About the speaker:
* Speaker: Stefan Hinze
* Company: ROWO Coating GmbH
* Event: Perovskite Connect 2026 | Berlin
* Location: Estrel, Berlin

Save the date: Perovskite Connect 2027 | 20 and 21 OCT 2027 | Berlin
Co-located with the Future of Electronics RESHAPED conference and exhibition
Learn more: https://www.techblick.com/perovskiteconnect

Intestered in exhibiting: learn more here: https://www.techblick.com/perovskiteconnect

#DMD, #BRAGMirror, #TransparentSolarCell, #33PercentTransmission, #TransparentPhotovoltaics, #OrganicPhotovoltaics

More Snippets
CONTACT US

KGH Concepts GmbH

Mergenthalerallee 73-75, 65760, Eschborn

+49 17661704139

admin@techblick.com

TechBlick is owned and operated by KGH Concepts GmbH

Registration number HRB 121362

VAT number: DE 337022439

  • LinkedIn
  • YouTube

Sign up for our newsletter to receive updates on our latest speakers and events AND to receive analyst-written summaries of the key talks and happenings in our events.

Thanks for submitting!

© 2026 by KGH Concepts GmbH

bottom of page