Thomas Österberg | Epishine: How do indoor spectra and 1,000x lower flux change solar-cell bandgap and electrode design?
07:15 - 08:40
Other snippets from this talk
Summary of the clip:
How do indoor spectra and 1,000x lower flux change solar-cell bandgap and electrode design?
Indoor and outdoor cells differ in two things: which wavelengths enter the cell, and how many photons in total. The outdoor solar spectrum runs all the way deep into IR, so bandgap positioning must account for it. Indoor light is confined to visible — incandescent bulbs wasted power by emitting IR — so here the bandgap is chosen to optimise efficiency in visible light.
Flux indoors is about 1,000 times less than outdoors, and that couples directly to cell design. It removes constraints: you no longer need to carry so much current, so conductivity requirements drop — primarily for the electrodes, which can be quite a bit lower. Lower flux, not higher, relaxes the electrode specification.
The contrast with high-volume outdoor work was made explicit: tens of thousands of cells in the preceding talk versus one cell here. A single cell is easy to make if you do not care about being out in the sun, but only about roughly this much flux — handled without too many losses.
In this short video, you can learn:
* Indoor and outdoor solar cells differ in two parameters: the wavelengths entering the cell and the total photon count.
* Indoor flux is roughly 1,000 times lower than outdoor flux, which relaxes current-carrying and electrode conductivity requirements.
* Because indoor light is confined to the visible, bandgaps are chosen for visible-spectrum efficiency rather than extended IR coverage.
📋 **Clip Abstract** Two variables separate indoor from outdoor photovoltaics: the spectral range reaching the cell and the photon flux. With indoor light confined to the visible and flux 1,000 times lower, both bandgap placement and electrode conductivity specs can be relaxed.
About the speaker:
* Speaker: Thomas Österberg
* Company: Epishine
* Event: Electronics RESHAPED 2026 | Berlin
* Location: Estrel, Berlin
USA: The Future of Electronics RESHAPED | USA
📅 Save the date: 9 and 10 June 2027
📍 Mountain View, California (Silicon Valley)
📋 Info: https://www.techblick.com/electronicsreshapedusa
Europe
The Future of Electronics RESHAPED | Berlin
📅 Save the date: 20 and 21 October 2027
📍 Berlin, Germany
📋 Info: https://www.techblick.com/electronicsreshaped
#IndoorSolarSpectrum, #BandgapPositioning, #ThousandFoldLowerFlux, #ElectrodeConductivity, #OrganicPhotovoltaics, #PrintedElectronics
This is a highlight of the presentation:
How Printed Organic Solar Is Transforming Consumer and IoT Electronics
More Highlights from the same talk.
08:17 - 09:58
Why does low-light OPV invert the usual series- versus parallel-resistance loss trade-off?
Why does low-light OPV invert the usual series- versus parallel-resistance loss trade-off?
In standard milliamp operation, increasing series resistance produces more and more losses: a lot of current passes, resistance is present, and power is lost. Varying parallel resistance only a little shows little effect; vary it a lot and loss eventually appears. Under indoor or low-light conditions the situation changes and is “actually backwards,” because the generated current drops to the microamp scale.
At microamp photocurrent, series resistance can be varied quite a lot without causing losses. Parallel resistance, another way of saying how shunted the device is, behaves differently: losses appear rapidly once leakage current through the device reaches the same order as the photocurrent. That leakage then causes big losses, reversing the usual emphasis on series-resistance management.
This low-light reversal explains why shunt-related leakage matters more than series resistance in indoor operation. The speaker notes that this is what happens in competitors’ cells, although not in theirs, tying the loss mechanism to device shunting rather than to the series-resistance penalty familiar from milliamp-scale IV curves.
In this short video, you can learn:
* Low-light OPV generates microamp photocurrent instead of milliamp current, making series resistance far less lossy.
* Parallel resistance or shunting becomes critical when leakage current approaches the photocurrent magnitude.
* Competitors’ cells exhibit this low-light shunt loss, while the speaker says theirs do not.
📋 **Clip Abstract** Low-light organic PV reverses the usual resistance-loss picture: microamp photocurrent makes series resistance tolerable, while parallel leakage becomes the dominant loss once it approaches the photocurrent. The clip contrasts this with milliamp operation, where series resistance causes losses and small parallel-resistance changes have little effect, and notes competitors’ cells show the low-light shunt problem.
About the speaker:
* Speaker: Thomas Österberg
* Company: Epishine
* Event: The Future of Photovoltaics 2021: Organic, Perovskites, CIGS, Hybrid
* Location: online
Join TechBlick - To learn more about emerging photovoltaic technologies incluing perovskites and organic photovoltaics
https://www.techblick.com/
#LowLightOPV, #SeriesResistance, #ParallelResistance, #MicroampPhotocurrent, #OrganicPhotovoltaics, #IndoorPV
10:29 - 11:27
Why is Epishine's new material stack 60% better in the lab, and why refuse percentage claims?
Why is Epishine's new material stack 60% better in the lab, and why refuse percentage claims?
For roughly seven years the production line ran on an unchanged material stack, a stability the speaker calls almost painful to admit. Now that the reasonably complex line is built and products are starting, that frozen stack can finally advance to newer, cooler semiconductors, with performance expected to creep up alongside the transition.
In the lab, devices built on the next-generation stack are 60% more efficient than the current generation. That number compares lab devices against today's shipping material rather than describing field output, and it represents the first real headroom the platform has had since the line was locked in seven years ago.
Percentages are deliberately kept out of indoor power discussions. The preferred metric is microwatts per square centimeter at a given lux, because indoor and outdoor operation involve different spectra and therefore different performance. Quoting a single percentage across those conditions, the argument goes, confuses people rather than informing them.
In this short video, you can learn:
* The material stack went unchanged for about seven years while the production line was being built out.
* Lab devices on the new semiconductors are 60% more efficient than the current shipping generation.
* Indoor output is reported in microwatts per square centimeter at a stated lux, not as a percentage.
📋 **Clip Abstract** Epishine is finally moving off a material stack frozen for roughly seven years, now that its production line and products are in place. Lab devices on the next-generation semiconductors are 60% more efficient than the current generation, though the company argues indoor output belongs in microwatts per square centimeter at a given lux rather than percentages.
About the speaker:
* Speaker: Thomas Österberg
* Company: Epishine
* Event: Electronics RESHAPED 2026 | Berlin
* Location: Estrel, Berlin
USA: The Future of Electronics RESHAPED | USA
📅 Save the date: 9 and 10 June 2027
📍 Mountain View, California (Silicon Valley)
📋 Info: https://www.techblick.com/electronicsreshapedusa
Europe
The Future of Electronics RESHAPED | Berlin
📅 Save the date: 20 and 21 October 2027
📍 Berlin, Germany
📋 Info: https://www.techblick.com/electronicsreshaped
#OrganicSolar, #MaterialStack, #IndoorPhotovoltaics, #MicrowattsPerLux, #PrintedElectronics, #IoTEnergyHarvesting
05:16 - 06:29
Why coat two half-cells and laminate them — and why treat a printed solar cell as a label?
Why coat two half-cells and laminate them — and why treat a printed solar cell as a label?
Instead of one monolithic device, two sub-solar cells — two half cells — are coated separately and then laminated together. That lamination step is the core IP, and it is how the material stack is built and how the properties that matter for the indoor setting are reached.
Because of that manufacturing method, the company can use a lot of materials that other players cannot use. The process route, not just the chemistry, is what unlocks that freedom — the coating and laminating sequence defines which materials are permissible in the finished stack.
Making the cell is not enough; a lot of backend work follows. The framing is that the solar cell is a label that also happens to be a solar cell — so label processes apply. Everything after the cell is completed runs on a label process line with quality control and encapsulation.
In this short video, you can learn:
* Two half cells are coated separately and then laminated together, which the speaker identifies as the core IP.
* The manufacturing method allows the use of many materials that other players cannot use.
* Once the cell is finished, everything that follows is run as part of the label process line, including quality control and encapsulation.
📋 **Clip Abstract** A printed organic solar cell is built by coating two half cells and laminating them, described as the core IP and the basis of the material stack. Treating the finished device as a label lets the backend, from quality control to encapsulation, run on label process lines.
About the speaker:
* Speaker: Thomas Österberg
* Company: Epishine
* Event: Electronics RESHAPED 2026 | Berlin
* Location: Estrel, Berlin
USA: The Future of Electronics RESHAPED | USA
📅 Save the date: 9 and 10 June 2027
📍 Mountain View, California (Silicon Valley)
📋 Info: https://www.techblick.com/electronicsreshapedusa
Europe
The Future of Electronics RESHAPED | Berlin
📅 Save the date: 20 and 21 October 2027
📍 Berlin, Germany
📋 Info: https://www.techblick.com/electronicsreshaped
#HalfCellLamination, #OrganicSolarCells, #IndoorPhotovoltaics, #BarrierEncapsulation, #PrintedElectronics, #FlexibleSolar
About this talk
→ How Printed Organic Solar Is Transforming Consumer and IoT Electronics · Thomas Österberg · The Future of Electronics RESHAPED 2026 Berlin
Other talks by Thomas Österberg
- Printed Organic PV For Low Light Applications · The Future of Photovoltaics: Organic, Perovskites, CIGS, Hybrid 2021
More highlights from Thomas Österberg
- ▶ Why does low-light OPV invert the usual series- versus parallel-resistance loss trade-off? · The Future of Photovoltaics 2021: Organic, Perovskites, CIGS, Hybrid


