Thomas Yang | Sino Applied Technology: What if you skip silicon oxide entirely and use 100β200 nm pure silicon with copper, SiC and graphene?
14:35 - 16:37
Other snippets from this talk
Summary of the clip:
What if you skip silicon oxide entirely and use 100β200 nm pure silicon with copper, SiC and graphene?
Instead of silicon oxide, the anode uses pure silicon with no silicon oxide present at all. The silicon material is minimised to particles of 100 to 200 nanometres, each with a copper coating. Shrinking the particles and removing the oxide is what lets the anode extend capacity toward the theoretical capacities of silicon rather than settling for the compromised oxide route.
During manufacturing, a very thin silicon carbide film forms between the silicon and the carbon. Silicon carbide is very strong with high force, which helps avoid the expansion that damages silicon anodes. It also provides very good conductivity compared to pure silicon, so the interlayer works on both the mechanical and the electrical problem at once.
The measured outcome is higher conductivity for the anode. First efficiency lands at 88 to 90, capacity is increased to 2,000 or 2,300, and cycle life is held at 800. Those three numbers together are the claim: capacity pushed up without giving away first-cycle efficiency or cycling stability.
In this short video, you can learn:
* The silicon is minimised to 100β200 nm particles with a copper coating and contains no silicon oxide.
* A very thin silicon carbide film forms between silicon and carbon during manufacturing, adding strength against expansion and better conductivity than pure silicon.
* The reported result is 88 to 90 first efficiency, 2,000 to 2,300 capacity and 800 cycle life.
π **Clip Abstract** Pure silicon anodes built from 100β200 nm copper-coated particles, with no silicon oxide present, are presented as a route to theoretical capacity. A very thin silicon carbide interlayer between silicon and carbon supplies expansion resistance and conductivity, supporting 88β90 first efficiency, 2,000β2,300 capacity and 800 cycles.
About the speaker:
* Speaker: Thomas Yang
* Company: Sino Applied Technology
* Event: Solid-State Batteries: Innovations, Promising Start-ups, Future Roadmap
* Location: Online
Join TechBlick to learn about the state of the art in solid state batteries, Si anode, advanced cathodes, sodium batteries, and beyond
https://www.techblick.com/
#SiliconCarbideInterlayer, #CopperCoatedNanoSilicon, #PureSiliconAnode, #HighFirstEfficiency, #LithiumIonBatteries, #AnodeMaterials
This is a highlight of the presentation:
Novel anode solution: graphene coating on nano silicon
More Highlights from the same talk.
10:20 - 12:37
Why accept 1,500 mAh/g from silicon oxide when pure silicon's theoretical capacity is 4,200?
Why accept 1,500 mAh/g from silicon oxide when pure silicon's theoretical capacity is 4,200?
A Stanford scientist applies graphene coating to silicon particles, using a graphene cage to avoid expansion and increase conductivity. The reported lab result is a very good coating on the silicon. But the process is CVD, and the manufacturing cost is very, very high. That makes commercialization in real applications not so easy.
Several Japanese companies are described as the most successful solution. They use silicon nanoparticles and downsize them to about 200 to 300 nanometers. In mass production, however, the particle size will be 2 microns to 5 microns. They then oxidize the silicon surface, turning it into silicon oxide, and at the same time sacrifice capacity.
The capacity trade-off is explicit. Pure silicon's theoretical capacity is 4,200 milliampere-hour per gram, while silicon oxide's normal and stable commercial capacity is 1,500 milliampere-hour per gram. The Japanese route therefore uses oxidation and accepts the lower stable number instead of the higher theoretical value for pure silicon.
In this short video, you can learn:
* A graphene cage on silicon particles can address expansion and conductivity in the lab, but the CVD coating cost is very high.
* Japanese producers downsize silicon nanoparticles to about 200β300 nm, while mass production particle size is 2β5 microns.
* Surface oxidation to silicon oxide stabilizes commercial capacity at 1,500 mAh/g, versus 4,200 mAh/g theoretical for pure silicon.
π **Clip Abstract** The clip contrasts a Stanford lab approach that coats silicon particles with graphene and uses a graphene cage for expansion and conductivity against the high cost of CVD manufacturing. It then describes Japanese silicon-oxide production, where nanoparticles are downsized, oxidized, and delivered at 1,500 mAh/g stable commercial capacity instead of pure silicon's 4,200 mAh/g theoretical capacity.
About the speaker:
* Speaker: Thomas Yang
* Company: Sino Applied Technology
* Event: Solid-State Batteries: Innovations, Promising Start-ups, Future Roadmap
* Location: Online
Join TechBlick to learn about the state of the art in solid state batteries, Si anode, advanced cathodes, sodium batteries, and beyond
https://www.techblick.com/
#GrapheneCoating, #SiliconOxideAnode, #CVDProcess, #NanoSiliconParticles, #BatteryMaterials, #EnergyStorage
18:13 - 20:24
After 45 coin-cell cycles, how much more capacity does a 5% graphene-coated nano-silicon anode hold than 5% silicon oxide?
After 45 coin-cell cycles, how much more capacity does a 5% graphene-coated nano-silicon anode hold than 5% silicon oxide?
In coin-cell tests run to 45 cycles, a 5% silicon oxide additive held only 80% of its capacity. The graphene-coated pure nano-silicon additive, at the same 5% loading, stayed at 86 to 87%. That is the core comparison: same dilution of the anode, but the coated silicon route gives up noticeably less capacity over the same cycle window.
The black curve is the normal graphite reference, with no silicon at all. It sits much higher, as expected, but the speaker's point is the shape: after roughly 50 cycles that capacity retention trace becomes much, much flatter than the silicon-blended cells, which is the bar any silicon additive has to narrow.
The second advantage claimed is higher C-rate output. The comparison spans pure graphite at 0% additive, the 5% nano-silicon, and competing silicon oxides at 5%, each across discharge rates. At 2C the gap widens sharply: the silicon oxide figure quoted for that rate is 86%, and the speaker stresses how much difference separates coated pure silicon from oxide blends.
In this short video, you can learn:
* At 45 coin-cell cycles, 5% silicon oxide retains about 80% capacity while 5% graphene-coated pure silicon holds 86 to 87%.
* The graphite reference sits higher and its retention curve flattens after about 50 cycles, setting the benchmark for any silicon additive.
* Across discharge rates up to 2C the nano-silicon advantage widens, with the silicon oxide retention cited at 2C at 86%.
π **Clip Abstract** Coin-cell data to 45 cycles put a 5% graphene-coated nano-silicon additive at 86 to 87% capacity retention against 80% for a 5% silicon oxide blend, with graphite as the higher reference whose retention curve flattens after about 50 cycles. The same material is pitched for higher C-rate output, where the spread between coated pure silicon and silicon oxide grows and the oxide figure at 2C is 86%.
About the speaker:
* Speaker: Thomas Yang
* Company: Sino Applied Technology
* Event: Solid-State Batteries: Innovations, Promising Start-ups, Future Roadmap
* Location: Online
Join TechBlick to learn about the state of the art in solid state batteries, Si anode, advanced cathodes, sodium batteries, and beyond
https://www.techblick.com/
#GrapheneCoating, #NanoSiliconAnode, #CapacityRetention, #HighRateDischarge, #LithiumIonBatteries, #AnodeMaterials
About this talk
β Novel anode solution: graphene coating on nano silicon Β· Thomas Yang Β· Battery Materials: Next-Gen & Beyond Lithium Ion 2022


