Tom Aernouts | Imec/EnergyVille: Can an additive cut scale-up losses while raising small-area efficiency, mainly through fill factor?
08:06 - 09:19
Other snippets from this talk
Summary of the clip:
Can an additive cut scale-up losses while raising small-area efficiency, mainly through fill factor?
The additive was introduced with the idea—often discussed—that small-area devices can show efficiency improvements. Different types of additives were studied. In this case, the additive is not only a small-area effect: when scaling up, it keeps upscaling losses even more minimal than without the additive.
The benefit appears both in small-area devices and in upscaling, as depicted with the stack and IV curves. On small area, the difference is not such a big difference, but it is still substantial: a 1% efficiency increase, mainly in fill factor in this case.
The key comparison is introducing the additive versus not doing so during scale-up. The reported result is that upscaling losses remain more minimal with the additive. The IV data also show a 1% efficiency gain on small area, mainly fill factor, so the additive affects both regimes.
In this short video, you can learn:
* The additive reduced upscaling losses compared with not using it.
* A 1% efficiency increase was observed on small-area devices, mainly from fill factor.
* The benefit was seen in both small-area devices and upscaling, with stack and IV curves shown.
📋 **Clip Abstract** This clip examines an additive for small-area devices and compares performance with scale-up. It reports that the additive keeps upscaling losses more minimal and delivers a 1% efficiency increase on small area, mainly through fill factor.
About the speaker:
* Speaker: Tom Aernouts
* Company: Imec/EnergyVille
* Event: Perovskite Connect 2026 | Berlin
* Location: Estrel, Berlin
Save the date: Perovskite Connect 2027 | 20 and 21 OCT 2027 | Berlin
Co-located with the Future of Electronics RESHAPED conference and exhibition
Learn more: https://www.techblick.com/perovskiteconnect
Intestered in exhibiting: learn more here: https://www.techblick.com/perovskiteconnect
#PerovskiteAdditive, #UpscalingLoss, #FillFactor, #IVCurve, #PerovskiteSolarCells, #PerovskiteModules
This is a highlight of the presentation:
Efficient Structures And Processes for Upscaling of Perovskite Modules and Tandems
21 and 22 OCT 2026
Estrel, Berlin
Organised By:
More Highlights from the same talk.
02:18 - 03:27
Which layers in a PIN perovskite minimodule are sputtered, wet-coated or evaporated?
Which layers in a PIN perovskite minimodule are sputtered, wet-coated or evaporated?
The minimodule starts on glass with ITO, nickel oxide and a SAM, patterned using P1, P2 and P3 scribing in a PIN architecture. ITO, nickel oxide and the SAM are described as sputtered in-house, while the SAM can alternatively be deposited by wet coating or evaporation. This covers the bottom layers before the perovskite.
For the perovskite absorber, wet coating is a possibility, but evaporation processes are also being introduced. The top stack then consists of an ETL and a metal, or alternatively ITO for semi-transparent modules. ITO can be sputtered, while the other top layers are deposited by evaporation, showing a mix of processes.
Across the stack, the described process sequence combines sputtering, wet coating and evaporation rather than a single deposition route. Scribing defines the mini-module or module, and the architecture is PIN on glass. For semi-transparent modules, ITO replaces the metal at the top, while the ETL remains part of the evaporated top layers.
In this short video, you can learn:
* P1, P2 and P3 scribing is used to make PIN perovskite mini-modules and modules on glass.
* ITO, nickel oxide and SAM are sputtered in-house, with the SAM also possible by wet coating or evaporation.
* The perovskite can be wet-coated, evaporation is being introduced, and the top ETL/metal or ITO stack uses evaporation plus sputtered ITO.
📋 **Clip Abstract** The clip outlines a PIN perovskite minimodule stack on glass with ITO, nickel oxide and SAM defined by P1–P3 scribing. It separates in-house sputtered layers from SAM wet coating or evaporation, perovskite wet coating and introduced evaporation, and evaporated ETL/metal top layers or sputtered ITO for semi-transparent modules.
About the speaker:
* Speaker: Tom Aernouts
* Company: Imec/EnergyVille
* Event: Perovskite Connect 2026 | Berlin
* Location: Estrel, Berlin
Save the date: Perovskite Connect 2027 | 20 and 21 OCT 2027 | Berlin
Co-located with the Future of Electronics RESHAPED conference and exhibition
Learn more: https://www.techblick.com/perovskiteconnect
Intestered in exhibiting: learn more here: https://www.techblick.com/perovskiteconnect
#PINArchitecture, #P1P2P3Scribing, #SputteredITO, #SAMWetCoating, #PerovskitePV, #SolarModuleUpscaling
13:23 - 15:10
Can hybrid FAPI deposition hit 24% and all-vacuum cells exceed 20%?
Can hybrid FAPI deposition hit 24% and all-vacuum cells exceed 20%?
The processing platform now includes evaporation: one evaporated layer in a hybrid two-step approach, and currently the full perovskite architecture. In the hybrid route, the 24% result refers specifically to FAPI deposition. Caesium bromide was introduced as an interlayer on the bottom and top of that layer, reaching high efficiencies in small-area devices, with stability results also shown.
For all-vacuum processing, the tool has only been up and running for a few months since the beginning of this year. The very first results already show more than 20% efficiency in all-vacuum processed cells. Some results are noted on somewhat larger areas. These are early data, but they establish the all-vacuum route operating beyond the 20% threshold.
The hybrid process is also being applied to two-terminal tandem technology. Development uses commercially available bottom cells that are fully textured; polished bottom cells were not explored. The team is deliberately going for the fully textured commercial type of cells. That choice links the hybrid perovskite work to fully textured commercial bottom-cell formats rather than a polished laboratory route.
In this short video, you can learn:
* Hybrid FAPI deposition with caesium bromide interlayers reached 24% in small-area devices, with stability data also reported.
* All-vacuum processed cells already exceed 20% efficiency in first results, with some data on somewhat larger areas.
* Two-terminal tandem development targets commercially available fully textured bottom cells, not polished bottom cells.
📋 **Clip Abstract** Evaporation has been added to the processing platform, first as one layer in a hybrid two-step approach and now across the full perovskite architecture. Hybrid FAPI deposition with caesium bromide interlayers reached 24% in small-area devices, all-vacuum cells exceeded 20%, and two-terminal tandem work uses fully textured commercial bottom cells.
About the speaker:
* Speaker: Tom Aernouts
* Company: Imec/EnergyVille
* Event: Perovskite Connect 2026 | Berlin
* Location: Estrel, Berlin
Save the date: Perovskite Connect 2027 | 20 and 21 OCT 2027 | Berlin
Co-located with the Future of Electronics RESHAPED conference and exhibition
Learn more: https://www.techblick.com/perovskiteconnect
Intestered in exhibiting: learn more here: https://www.techblick.com/perovskiteconnect
#HybridFAPIDeposition, #CaesiumBromideInterlayer, #AllVacuumPerovskite, #FullyTexturedTandem, #PerovskiteSolarCells, #PerovskiteTandems
11:13 - 12:45
What do accelerated and outdoor tests show about whether semi-transparent perovskite devices survive damp heat and outdoor exposure?
What do accelerated and outdoor tests show about whether semi-transparent perovskite devices survive damp heat and outdoor exposure?
The architecture removes the metallic back electrode and uses spotted ITO also as the back electrode, producing a semi-transparent device. Performance is a little lower because some light escapes the structure. Avoiding the metallic electrode allows better study of stability and degradation mechanisms intrinsically in the device.
Accelerated tests on this architecture covered constant illumination at room temperature, later higher temperature, light-dark cycling, thermal cycling and damp heat for up to 1,000 hours, with fairly good performance. Indoor accelerated testing is used first; when results look promising, the work moves to outdoor testing.
The outdoor testing is running at many locations and has been running for quite some time. By the end of last year the data covered about half a year, more or less, and testing was still running. The result is T85.
In this short video, you can learn:
* Replacing the metallic back electrode with spotted ITO makes a semi-transparent device, but performance drops because light escapes.
* Indoor accelerated tests covered constant illumination, light-dark cycling, thermal cycling and damp heat up to 1,000 hours with fairly good performance.
* Outdoor testing at many locations had about half a year of data by the end of last year and was still running at T85.
📋 **Clip Abstract** A semi-transparent architecture replaces the metallic back electrode with spotted ITO, accepting lower performance from light escape to study intrinsic degradation. Accelerated indoor tests—constant illumination, light-dark and thermal cycling, and 1,000 hours of damp heat—preceded outdoor testing at many locations, with roughly half a year of data by the end of last year and T85 still running.
About the speaker:
* Speaker: Tom Aernouts
* Company: Imec/EnergyVille
* Event: Perovskite Connect 2026 | Berlin
* Location: Estrel, Berlin
Save the date: Perovskite Connect 2027 | 20 and 21 OCT 2027 | Berlin
Co-located with the Future of Electronics RESHAPED conference and exhibition
Learn more: https://www.techblick.com/perovskiteconnect
Intestered in exhibiting: learn more here: https://www.techblick.com/perovskiteconnect
#SemiTransparentPerovskite, #SpottedITO, #DampHeatTesting, #LightDarkCycling, #PerovskiteSolarCells, #OutdoorStability
About this talk
→ Efficient Structures And Processes for Upscaling of Perovskite Modules and Tandems · Tom Aernouts · Perovskite Connect 2026
Other talks by Tom Aernouts
- Stable and efficient architectures for perovskite solar modules and tandems · The Future of Photovoltaics: Organic, Perovskites, CIGS, Tandem 2022


